文件类型：XLS/Microsoft Excel 文件大小：字节
"第1组国产男皮鞋"
"契约条款附件一"
"第1组;第1页;共1页"
"第1组:国产男皮鞋采购规范表"
"项目",,,"第1项","第2项","第3项","第4项","检验方法"
"规格"
1,"鞋面","材质:牛皮","ˇ","ˇ","ˇ","ˇ","放大镜分析"
2,,"厚度:1.2 ~ 1.6mm","ˇ","ˇ","ˇ","ˇ","CNS 1274"
3,,"抗拉强度:120 kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1278"
4,,"撕裂强度:3.0 kgf/mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1279"
5,,"破裂强度:25 kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1353"
6,,"延伸率:30%(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1281"
7,"内里","材质:牛皮(可搭配纺织透气材料)","ˇ","ˇ","ˇ","ˇ","放大镜分析"
8,,"厚度:0.8 mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1274"
9,"中底","材质:三合一定型纸浆+铁心或不织布中底","ˇ","ˇ","ˇ","ˇ","放大镜分析"
10,"鞋垫","牛皮衬里+吸震发泡材料","ˇ",,"ˇ",,"放大镜分析"
,,"纺织衬里+吸震发泡材料",,"ˇ",,"ˇ","放大镜分析"
11,,"抗菌:接触面无细菌滋生","ˇ","ˇ","ˇ","ˇ","AATCC147:98金色葡萄球菌ATCC6538P"
12,"鞋底","材质:","橡胶或复合底","橡胶或复合底","皮革底","皮革底","放大镜分析"
13,,"厚度: mm(含)以上",2.5,2.5,3.5,3.5,"橡胶底:CNS 4869;皮革底:CNS 1274"
14,,"抗拉强度:__kgf/cm2(含)以上",100,100,60,60,"CNS3553,2型试片(橡胶),CNS 1278(皮革)"
15,,"撕裂强度:__kgf/cm(含)以上",30,30,"-","-","CNS3559,B型试片"
16,,"延伸率: %(含)以上",300,300,"-","-","CNS3553,2型试片"
17,,"耐磨:损失量____mm3(含)以下",150,150,"-","-","DIN 53516"
18,,"止滑系数:乾式0.5(含)以上","ˇ","ˇ","ˇ","ˇ","ASTM-F1677"
,,"止滑系数:湿式0.3(含)以上","ˇ","ˇ","ˇ","ˇ"
19,"鞋跟","耐磨:损失量150mm3(含)以下","ˇ","ˇ","ˇ","ˇ","DIN 53516"
20,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
21,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每10 "
,," 公分需有10针(含)以上."
22,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案"
,," ,文字批号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
23,"验收","1. 规范表第20,21,22项由适用机关以目视检查办理. "
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制造厂"
,," 之检验报告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验合格其费"
,," 用由适用机关负担,如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数量在500双"
,," (含)以上,适用机关得选择(1)制造厂检验报告或(2)制造厂送交具公信力第三者检验单位(如经济部标"
,," 准检验局,鞋类暨运动休闲科技研发中心等),得会同立约商代表依CNS2779 Z4006(计数值检验程序"
,," 及抽样表)(采用S-1特殊检验水准,以双为单位,允收水准AQL为4%),办理抽样及检验,检验费"
,," 用由立约商负担."
"第2组国产女皮鞋"
" "
"第2组;第页;共2页"
"第2组:国产女皮鞋采购规范表"
"项目",,,"第1项","第2项","第3项","第4项","检验方法"
"规格"
1,"鞋面","材质:牛皮","ˇ","ˇ","ˇ","ˇ","放大镜分析"
2,,"厚度:1.2 ~ 1.4 mm","ˇ","ˇ","ˇ","ˇ","CNS 1274"
3,,"抗拉强度:120 kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1278"
4,,"撕裂强度:3.0 kgf/mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1279"
5,,"破裂强度:25 kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1353"
6,,"延伸率:30%(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1281"
7,"内里","材质:牛皮(可搭配纺织透气材料)","ˇ","ˇ","ˇ","ˇ","放大镜分析"
8,,"厚度:0.8 mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1274"
9,"中底","材质:三合一定型纸浆+铁心或不织布中底","ˇ","ˇ","ˇ","ˇ","放大镜分析"
10,"鞋垫","牛皮衬里+吸震发泡材料","ˇ",,"ˇ",,"放大镜分析"
,,"纺织衬里+吸震发泡材料",,"ˇ",,"ˇ","放大镜分析"
11,,"抗菌:接触面无细菌滋生","ˇ","ˇ","ˇ","ˇ","AATCC147:98金色葡萄球菌ATCC6538P"
12,"鞋底","材质:","美耐底","美耐底","皮革底","皮革底","放大镜分析"
13,,"厚度: mm(含)以上",3.5,3.5,3,3,"美耐底:CNS 4869;皮革底:CNS 1274"
14,,"抗拉强度:60kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","CNS3553,2型试片(橡胶),CNS 1278(皮革)"
15,,"撕裂强度:__kgf/cm(含)以上",20,20,"-","-","CNS3559,B型试片"
16,,"延伸率: %(含)以上",150,150,"-","-","CNS3553,2型试片"
17,,"耐磨:损失量 400 mm3(含)以下","ˇ","ˇ","ˇ","ˇ","DIN 53516"
18,,"止滑系数:乾式 0.5(含)以上","ˇ","ˇ","ˇ","ˇ","ASTM-F1677"
,,"止滑系数:湿式 0.3(含)以上","ˇ","ˇ","ˇ","ˇ"
19,"鞋跟","耐磨:损失量 250 mm3(含)以下","ˇ","ˇ","ˇ","ˇ","DIN 53516"
20,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
21,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每10 "
,," 公分需有10针(含)以上."
22,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案"
,," ,文字批号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
23,"验收","1. 规范表第20,21,22项由适用机关以目视检查办理. "
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制造厂"
,," 之检验报告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验合格其费用"
,," 由适用机关负担,如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数量在500双(含)"
,," 以上,适用机关得选择(1)制造厂检验报告或(2)制造厂送交具公信力第三者检验单位(如经济部标准检"
,," 验局,鞋类暨运动休闲科技研发中心等),得会同立约商代表依CNS2779 Z4006(计数值检验程序及抽样"
,," 表)(采用S-1特殊检验水准,以双为单位,允收水准AQL为4%),办理抽样及检验,检验费用由立约"
,," 商负担."
"第3组国产男休闲鞋"
"第3组;第页;共2页"
"第3组:国产男休闲鞋采购规范表"
"项目",,,"第1项","第2项","第3项","第4项","第5项","第6项","第7项","第8项","第9项","第10项","第11项","第12项","检验方法"
"规格"
1,"鞋面","材质:牛皮","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","放大镜分析"
2,,"厚度:1.4 ~ 1.8 mm","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1274"
3,,"抗拉强度:120 kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1278"
4,,"撕裂强度:3.0 kgf/mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1279"
5,,"破裂强度:25 kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1353"
6,,"延伸率:30 %(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1281"
7,"内里","材质:牛皮(可搭配纺织透气材料)","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","-","-","-","-","-","-","放大镜分析"
,,"材质:猪皮(可搭配纺织透气材料)","-","-","-","-","-","-","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","放大镜分析"
8,,"厚度:0.8 mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1274"
9,"鞋垫","牛皮衬里+吸震发泡材料","ˇ","ˇ","ˇ","-","-","-","-","-","-","-","-","-","放大镜分析"
,,"猪皮衬里+吸震发泡材料","-","-","-","-","-","-","ˇ","ˇ","ˇ","-","-","-","放大镜分析"
,,"纺织衬里+吸震发泡材料","-","-","-","ˇ","ˇ","ˇ","-","-","-","ˇ","ˇ","ˇ","放大镜分析"
10,,"抗菌:接触面无细菌滋生","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","AATCC147:98金色葡萄球菌ATCC6538P"
11,"鞋底","材质:","橡胶或复合底","PU底","TPR底","橡胶或复合底","PU底","TPR底","橡胶或复合底","PU底","TPR底","橡胶或复合底","PU底","TPR底","放大镜分析"
12,,"厚度:2.5 mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 4869(橡胶,PU,TPR)"
13,,"抗拉强度:__kgf/cm2(含)以上",100,60,50,100,60,50,100,60,50,100,60,50,"CNS3553,2型试片(橡胶,PU,TPR)"
14,,"撕裂强度:__kgf/cm(含)以上",30,25,20,30,25,20,30,25,20,30,25,20,"CNS3559,B型试片"
15,,"延伸率: %(含)以上",300,250,250,300,250,250,300,250,250,300,250,250,"CNS3553,2型试片"
16,,"耐磨:损失量____mm3(含)以下",150,250,280,150,250,280,150,250,280,150,250,280,"DIN 53516"
17,"鞋底","止滑系数:乾式 0.5 (含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ASTM-F1677"
,,"止滑系数:湿式 0.3 (含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ"
18,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
19,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋5针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每10公分需有10 "
,," 针(含)以上. "
20,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案,文字批"
,," 号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
21,"验收","1. 规范表第18,19,20项由适用机关以目视检查办理. "
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制造厂之检验报"
,," 告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验合格其费用由适用机关负担如"
,," 不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数量在500双(含)以上,适用机关得选择(1)制"
,," 造厂检验报告或(2)制造厂送交具公信力第三者检验单位(如经济部标准检验局,鞋类暨运动休闲科技研发中心等"
,," ),得会同立约商代表依CNS2779 Z4006(计数值检验程序及抽样表)(采用S-1特殊检验水准,以双为单位,允"
,," 收水准AQL为4%),办理抽样及检验,检验费用由立约商负担."
"第4组国产女休闲鞋"
"第4组;第页;共2页"
"第4组:国产女休闲鞋采购规范表"
"项目",,,"第1项","第2项","第3项","第4项","第5项","第6项","第7项","第8项","第9项","第10项","第11项","第12项","检验方法"
"规格"
1,"鞋面","材质:牛皮","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","放大镜分析"
2,,"厚度:1.4 ~ 1.8 mm","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1274"
3,,"抗拉强度:120 kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1278"
4,,"撕裂强度:3.0 kgf/mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1279"
5,,"破裂强度:25 kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1353"
6,,"延伸率:30%(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1281"
7,"内里","材质:牛皮(可搭配纺织透气材料)","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","-","-","-","-","-","-","放大镜分析"
,,"材质:猪皮(可搭配纺织透气材料)","-","-","-","-","-","-","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","放大镜分析"
8,,"厚度:0.8 mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1274"
9,"鞋垫","牛皮衬里+吸震发泡材料","ˇ","ˇ","ˇ","-","-","-","-","-","-","-","-","-","放大镜分析"
,,"猪皮衬里+吸震发泡材料","-","-","-","-","-","-","ˇ","ˇ","ˇ","-","-","-","放大镜分析"
,,"纺织衬里+吸震发泡材料","-","-","-","ˇ","ˇ","ˇ","-","-","-","ˇ","ˇ","ˇ","放大镜分析"
10,,"抗菌:接触面无细菌滋生","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","AATCC147:98金色葡萄球菌ATCC6538P"
11,"鞋底","材质:","橡胶或复合底","PU底","TPR底","橡胶或复合底","PU底","TPR底","橡胶或复合底","PU底","TPR底","橡胶或复合底","PU底","TPR底","放大镜分析"
12,,"厚度:2.5 mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 4869(橡胶,PU,TPR)"
13,,"抗拉强度:__kgf/cm2(含)以上",100,60,50,100,60,50,100,60,50,100,60,50,"CNS3553,2型试片(橡胶,PU,TPR)"
14,"鞋底","撕裂强度:__kgf/cm(含)以上",30,25,20,30,25,20,30,25,20,30,25,20,"CNS3559,B型试片"
15,,"延伸率: %(含)以上",300,250,250,300,250,250,300,250,250,300,250,250,"CNS3553,2型试片"
16,,"耐磨:损失量____mm3(含)以下",150,250,280,150,250,280,150,250,280,150,250,280,"DIN 53516"
17,,"止滑系数:乾式0.5 (含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ASTM-F1677"
,,"止滑系数:湿式0.3 (含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ"
18,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
19,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每10公分需有10 "
,," 针(含)以上. "
20,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案,文字批"
,," 号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
21,"验收","1. 规范表第18,19,20项由适用机关以目视检查办理. "
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制造厂之检验报"
,," 告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验合格其费用由适用机关负担,"
,," 如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数量在500双(含)以上,适用机关得选择(1)"
,," 制造厂检验报告或(2)制造厂送交具公信力第三者检验单位(如经济部标准检验局,鞋类暨运动休闲科技研发中心"
,," 等),得会同立约商代表依CNS2779 Z4006(计数值检验程序及抽样表)(采用S-1特殊检验水准,以双为单位,"
,," 允收水准AQL为4%),办理抽样及检验,检验费用由立约商负担."
"第5组国产运动鞋"
"第5组;第页;共2页"
"第5组:国产运动鞋采购规范表"
"项目",,,"第1项","第2项","检验方法"
"规格"
1,"鞋面","材质:PU+透气网布","ˇ","ˇ","放大镜分析"
2,,"破裂强度:成品鞋常温60度弯曲60,000次(含)以上,鞋面无破损","ˇ","ˇ","SATRA TM92"
3,"里衬","材质:纺织布","ˇ","ˇ","放大镜分析"
4,,"秀气度:15 sec/100 ml(含)以下","ˇ","ˇ","CNS 1357"
5,"中底","材质:纸浆或不织布","ˇ","ˇ","放大镜分析"
6,,"吸水脱附:水份吸收≥70 mg/cm2;水份脱离≥80%的水份吸收","ˇ","ˇ","EN ISO 20344 7.2"
7,"鞋垫","材质:纺织布+吸震发泡材料","ˇ","ˇ","放大镜分析"
8,,"厚度:3 ~ 5 mm","ˇ","ˇ","CNS 1274"
9,,"防霉:1级(滋生面积≤10%)","ˇ","ˇ","ASTM-G21:96白癣菌ATCC9533"
10,,"抗菌:接触面无细菌滋生","ˇ","ˇ","AATCC147:98金色葡萄球菌ATCC6538P"
11,,"透气度:30 sec/100ml(含)以下","ˇ","ˇ","CNS 1357"
12,"中插","材质:","EVA","-","材质分析"
13,,"抗拉强度:____kgf/cm2(含)以上",18,"-","CNS3553,2型试片"
14,,"延伸率:: %(含)以上",200,"-","CNS3553,2型试片"
15,,"撕裂强度:____kgf/cm(含)以上",10,"-","CNS3559,B型试片"
16,,"硬度:HS","52~58","-","CNS Type:E型"
17,,"压缩变形: %(含)以下",55,"-","CNS3560,50.C,6hr"
18,"鞋底","材质: ","橡胶或复合底","TPR","放大镜分析"
19,,"厚度: mm(含)以上",2.5,2.5,"CNS 4869(橡胶,TPR)"
20,,"延伸率:: %(含)以上",360,200,"CNS 734"
21,,"抗拉强度:____kgf/cm2(含)以上",100,50,"CNS3553,2型试片(橡胶,TPR)"
22,,"鞋底与鞋面胶著强度:__kg(含)以上",20,15,"CNS 742"
23,,"吸震性: g(含)以下",12,15,"SATRA TM 142"
24,,"耐磨:2磅2,000转__CC(含)以下",0.3,0.5,"CNS 734"
25,,"止滑系数:乾式____(含)以上",0.5,0.35,"ASTM-F1677"
,,"止滑系数:湿式____(含)以上",0.3,0.25
26,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
27,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每10公分"
,," 需有10针(含)以上. "
28,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案,文"
,," 字批号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
29,"验收","1. 规范表第26,27,28项由适用机关以目视检查办理. "
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制造厂"
,," 之检验报告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验合格其费用"
,," 由适用机关负担,如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数量在500双(含)"
,," 以上,适用机关得选择(1)制造厂检验报告或(2)制造厂送交具公信力第三者检验单位(如经济部标准检"
,," 验局,鞋类暨运动休闲科技研发中心等),得会同立约商代表依CNS2779 Z4006(计数值检验程序及抽样"
,," 表)(采用S-1特殊检验水准,以双为单位,允收水准AQL为4%),办理抽样及检验,检验费用由立约"
,," 商负担."
"第6组皮革制安全鞋"
"第6组;第页;共2页"
"第6组:国产皮革制安全鞋(CNS 6863)采购规范表"
"*作业性质分类:H类为重作业用;S类为普通作业用;L类为轻作业用"
"项目",,,"第1项","第2项","第3项","第4项","第5项","第6项","检验方法"
"规格"
1,"性质","作业性质分类","(H)","(S)","(L)","(H)","(S)","(L)","-"
2,"鞋面","材质:皮革__(含)以上",1.5,1.5,1.2,1.5,1.5,1.2,"CNS 6863 5.2"
3,,"面皮龟裂:高度6mm(含)以上,载重15kgf(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 7.1"
4,,"含铬量:V式及I式3.0～5.5%以内","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 7.1"
5,"钢头","圆顶后端中央点至先端距离____mm","40~60","40~60","30~60","40~60","40~60","30~60","CNS 6863 5.2.3"
6,,"高度:____mm(含)以上",33,33,28,33,33,28,"CNS 6863 5.2.3"
7,,"摺边尺寸:3mm(含)以上,如为斜角者1mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 5.2.3"
8,,"耐压扁 :空隙22mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 7.2"
9,,"耐蚀性:不得有腐蚀痕迹","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 7.2"
10,"鞋底","材质分析:合成橡胶大底","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 7.3"
11,,"止滑性:具止滑作用","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 2.1"
,,"最薄处厚度:____mm(含)以上",3.5,3,2.5,3.5,3,2.5,"CNS 6863 5.2.4"
12,,"抗拉强度:____kgf/cm2(含)以上",140,140,100,140,140,100,"CNS 6863 7.3.(CNS3553,#2号试片)"
13,,"伸长率:____%(含)以上",300,300,200,300,300,200,"CNS 6863 7.3(CNS3553,#2号试片)"
14,,"撕裂强度:____kgf/cm(含)以上",35,35,30,35,35,30,"CNS 6863 7.3(CNS3559,#B号试片)"
15,,"硬度Hs(含)以上",60,60,50,60,60,50,"CNS 6863 7.3(CNS3553,Type-A)"
16,,"耐油性","+10%~-0%","+10%~-0%","+30%~-0%","+10%~-0%","+10%~-0%","+30%~-0%","CNS 6863 7.3.(CNS3562,40±1℃*22H)"
17,,"老化后鞋底弯折:不得折断","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 7.3(70±1℃*120H)"
18,,"老化5天后抗拉强度降低率____%(含)以下",15,15,"-",15,15,"-","CNS 68637.3 (CNS3556,70±1℃*120H) "
19,"鞋底用缝线","抗拉强度:钩缝,内缝线28kgf/根以上,露缝线19 kgf/根以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 7.5"
20,"成品鞋","耐压扁:空隙15mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 4.1"
21,,"耐冲击:空隙15mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 4.1"
22,,"胶著力:____kgf(含)以上",30,30,25,30,30,25,"CNS 6863 4.2(鞋底与鞋面)"
23,,"耐穿刺:静荷重50 kgf是否贯穿鞋底","ˇ","ˇ","-","ˇ","ˇ","-","CNS 6863 4.3(可依据需求增加)"
24,,"抗静电试验:符合CNS 8878要求","ˇ","ˇ","ˇ","-","-","-","CNS 8878(可依据需求增加)"
25,,"耐电压:不得有任何异样且泄漏电流最大不得超过16mA","-","-","-","ˇ","ˇ","ˇ","60Hz交流电压15,000伏特连续1分钟(可依据需求增加)"
26,,"破坏电压:未贯穿","-","-","-","ˇ","ˇ","ˇ","60Hz交流电压20,000伏特连续1分钟(可依据需求增加)"
27,,"止滑性试验:乾式0.5(含)以上;湿式0.3(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ASTM-F1677(可依据需求增加)"
28,,"耐磨耗:150mm3(含)以下","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","DIN53516(可依据需求增减)"
29,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
30,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每10公分"
,," 需有10针(含)以上. "
31,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案,文"
,," 字批号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
,,"3. 贴有经济部标准检验局授权之合格认证标签;或通过ISO9000国际品质认证或是通过经济部标准检验局"
,," 安全鞋产品登录认证."
32,"验收","1. 规范表第29,30,31项由适用机关以目视检查办理."
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制造厂"
,," 之检验报告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验合格其费用"
,," 由适用机关负担,如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数量在500双 (含"
,," )以上,适用机关得选择(1)制造厂检验报告或(2)制造厂送交具公信力第三者检验单位(如经济部标准检"
,," 验局,鞋类暨运动休闲科技研发中心等),得会同立约商代表依CNS2779 Z4006(计数值检验程序及抽样"
,," 表)(采用S-1特殊检验水准,以双为单位,允收水准AQL为4%),办理抽样及检验,检验费用由立约"
,," 商负担."
"第7组PU鞋底安全鞋"
"第7组;第页;共2页"
"第7组:PU鞋底安全鞋(CNS 12708)采购规范表"
"※作业性质分类:PU-S为普通作业用;PU-L为轻工作用"
"项目",,,"第1项","第2项","第3项","第4项","检验方法"
"规格"
1,"性质","作业性质分类","(PU-S)","(PU-L)","(PU-S)","(PU-L)","-"
2,"鞋面","材质:皮革__(含)以上",1.5,1.2,1.5,1.2,"CNS 6863 5.2"
3,,"面皮龟裂:高度6.0mm(含)以上,载重15.0kgf(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 8.4"
4,,"含铬量:V式及I式3.0～5.5%以内","ˇ","ˇ","ˇ","ˇ","CNS 6863 8.4"
5,"钢头","圆顶后端中央点至先端距离____mm","40~60","30~50","40~60","30~50","CNS 6863 5.2.3"
6,,"高度:____mm(含)以上",33,28,33,28,"CNS 6863 5.2.3"
7,,"摺边尺寸:3mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 5.2.3"
8,,"耐压扁 :空隙15mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 8.1"
9,,"耐撞击 :空隙15mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 8.2"
10,,"耐蚀性:不得有腐蚀痕迹","ˇ","ˇ","ˇ","ˇ","CNS 6863 8.5"
11,"鞋底","大底材质分析:PU大底","ˇ","ˇ","ˇ","ˇ","红外线光谱仪"
12,,"抗拉强度:____kgf/cm2(含)以上",60,60,60,60,"CNS 6863 8.6(CNS3553,#2号试片)"
13,,"伸长率:____%(含)以上",300,300,300,300,"CNS 6863 8.6(CNS3553,#2号试片)"
14,,"撕裂强度:____kgf/cm(含)以上",25,25,25,25,"CNS 6863 8.6(CNS3559,#B号试片)"
15,,"老化(抗拉强度变化率)____%","±20%","±20%","±20%","±20%","CNS 6863 8.6(70±1℃*120H)"
16,,"耐油(体积变化率)","+10%~-0%","+10%~-0%","+10%~-0%","+10%~-0%","CNS3562,40±1℃*22H"
17,,"抗剥离性:____ kgf",30,25,30,25,"CNS 6863 8.3"
18,"成品鞋","耐压扁:空隙15mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 4.1"
19,,"耐冲击:空隙15mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 4.1"
20,,"胶著力:____kgf(含)以上",30,25,30,25,"CNS 6863 4.2(鞋底与鞋面)"
21,,"耐穿刺:静荷重50 kgf是否贯穿鞋底","-","-","ˇ","ˇ","CNS 6863 4.3(可依据需求增加)"
22,,"抗静电试验:符合CNS 8878要求","-","-","ˇ","ˇ","CNS 8878(可依据需求增加)"
23,,"止滑性试验:乾式0.5(含)以上;湿式0.3(含)以上","-","-","ˇ","ˇ","ASTM-F1677(可依据需求增加)"
24,,"耐磨耗:250mm3(含)以下","-","-","ˇ","ˇ","DIN53516. (可依据需求增减) "
25,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
26,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每"
,," 10公分需有10针(含)以上. "
27,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图"
,," 案,文字批号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
,,"3. 贴有经济部标准检验局授权之合格认证标签;或通过ISO9000国际品质认证或是通过经济部标准"
,," 检验局安全鞋产品登录认证."
28,"验收","1. 规范表第25,26,27项由适用机关以目视检查办理."
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制"
,," 造厂之检验报告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验"
,," 合格其费用由适用机关负担,如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购"
,," 数量在500双(含)以上,适用机关得选择(1)制造厂检验报告或(2)制造厂送交具公信力第三者检验"
,," 单位(如经济部标准检验局,鞋类暨运动休闲科技研发中心等),得会同立约商代表依"
,," CNS2779 Z4006(计数值检验程序及抽样表)(采用S-1特殊检验水准,以双为单位,允收水准AQL"
,," 为4%),办理抽样及检验,检验费用由立约商负担."
"第8组国产雨鞋"
"第8组;第页;共1页"
"第8组:国产雨鞋采购规范表"
"项目",,,"第1项","第2项","检验方法"
"规格"
1,"鞋面","材质","橡胶","PVC","放大镜分析"
2,,"高度(筒身橡胶部分离地高度)____cm,中,短统雨鞋(男性用)不限高度","30±2cm","30±2cm","CNS 4870(可依需求增减)"
3,,"抗拉强度:____kgf/cm2(含)以上",30,30,"CNS 3479"
4,,"耐寒试验","无异状","无异状","CNS 3479"
5,,"浸水试验","无异状","无异状","CNS 3479"
6,"鞋垫","材质不限,由厂商自行提供","ˇ","ˇ","-"
7,"鞋底","材质:","橡胶或复合底","PVC","放大镜分析"
8,,"厚度:不著地 cm(含)以上",0.2,0.2,"CNS 4869(橡胶,PVC)"
9,,"抗拉强度:____kgf/cm2(含)以上",30,30,"CNS 3479"
10,,"延伸率: %(含)以上",120,120,"CNS 3479"
11,,"不渗透性","不渗漏,未膨胀,未硬化及未龟裂","不渗漏,未膨胀,未硬化及未龟裂","CSN12707 A-1"
12,,"止滑系数:乾式0.6(含)以上","ˇ","ˇ","ASTM-F1677"
13,,"止滑系数:湿式0.4(含)以上","ˇ","ˇ"
14,"筒身","筒身顶部:须有绳索束紧功能并带lock装置","ˇ","ˇ","放大镜分析"
15,,"厚度:0.1cm(含)以上","ˇ","ˇ","CNS 4870"
16,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
17,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每10 "
,," 公分需有10针(含)以上."
18,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案"
,," ,文字批号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
19,"验收","1. 规范表第16,17,18项由适用机关以目视检查办理. "
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制造"
,," 厂之检验报告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验由适"
,," 用机关负担,如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数量在500双(含)"
,," 以上,适用机关得选择(1)制造厂检验报告或(2)制造厂送交具公信力第三者检验单位(如经济部标准"
,," 检验局,鞋类暨运动休闲科技研发中心等),得会同立约商代表依CNS2779 Z4006(计数值检验程序"
,," 样表)(采用S-1特殊检验水准,以双为单位,允收水准AQL为4%),办理抽样及检验,检验费用"
,," 由立约商负担."
"第9组国产消防救护用工作鞋"
"第9组;第页;共3页"
"第9组:国产消防救护用工作鞋采购规范表"
"项目",,,"第1项","第2项","第3项","第4项","检验方法"
"规格"
1,"鞋面","材质:牛皮","ˇ","ˇ","ˇ","ˇ","放大镜分析"
2,,"厚度:1.6~1.8mm","ˇ","ˇ","ˇ","ˇ","CNS 1274"
3,,"抗拉强度:120kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1278"
4,,"撕裂强度:3kgf/mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1279"
5,,"破裂强度:25kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1353"
6,,"延伸率:30%(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1281"
7,"鞋统","材质:纺织材料+泡棉或针轧棉","ˇ","ˇ","ˇ","ˇ","放大镜分析"
8,,"泡棉或针轧棉厚度:2.5mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1274"
9,"内里","材质:纺织衬里+吸震发泡材料","ˇ","ˇ","ˇ","ˇ","放大镜分析"
10,,"发泡材料厚度:3mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1274"
11,"后包","材质:牛皮","ˇ","ˇ","ˇ","ˇ","放大镜分析"
12,,"厚度:1.6~1.8mm","ˇ","ˇ","ˇ","ˇ","CNS 1274"
13,"鞋舌","材质:纺织材料+泡棉或针轧棉","ˇ","ˇ","ˇ","ˇ","放大镜分析"
14,,"泡棉或针轧棉厚度:2.2mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1274"
15,"滚口","材质:纺织材料+泡棉或针轧棉","ˇ","ˇ","ˇ","ˇ","放大镜分析"
16,,"泡棉或针轧棉厚度:20mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1274"
17,"鞋眼","古铜色单脚D型环7个(1-2,4-8)及古铜色双脚D型环1个(3)","ˇ","ˇ","ˇ","ˇ","放大镜分析"
18,"鞋垫","材质1:牛皮衬里+吸震发泡材料","ˇ","ˇ","-","-","放大镜分析"
19,,"材质2:纺织衬里+吸震发泡材料","-","-","ˇ","ˇ","放大镜分析"
20,,"抗菌:接触面无细菌滋生","ˇ","ˇ","ˇ","ˇ","AATCC147:98金色葡萄球菌ATCC6538P"
21,"鞋底","材质:橡胶或复合底","ˇ","ˇ","ˇ","ˇ","放大镜分析"
22,,"厚度:3.5mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 4869(橡胶)"
23,,"抗拉强度:140kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","CNS3553,2型试片(橡胶),CNS 1278(皮革)"
24,,"撕裂强度:30kgf/cm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS3559,B型试片"
25,,"延伸率:300%(含)以上","ˇ","ˇ","ˇ","ˇ","CNS3553,2型试片"
26,,"耐油性:+10%~-0%","ˇ","ˇ","ˇ","ˇ","CNS3562,40±1℃*22H"
27,"鞋跟","耐磨:损失量150mm3(含)以下","ˇ","ˇ","ˇ","ˇ","DIN 53516"
28,"成品鞋","耐压扁:空隙15mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 4.1(H级)"
29,,"耐冲击:空隙15mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 4.1(H级)"
30,,"胶著力:30kgf(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 4.2(鞋底与鞋面)"
31,,"耐穿刺:静荷重50 kgf是否贯穿鞋底","ˇ","ˇ","ˇ","ˇ","CNS 6863 4.3(可依据需求增加)"
32,,"抗静电试验:符合CNS 8878要求","ˇ","-","ˇ","-","CNS 8878(可依据需求增加)"
33,,"耐电压:不得有任何异样且泄漏电流最大不得超过16mA","-","ˇ","-","ˇ","60Hz交流电压15,000伏特连续1分钟(可依据需求增加)"
34,,"破坏电压:未贯穿","-","ˇ","-","ˇ","60Hz交流电压20,000伏特连续1分钟(可依据需求增加)"
35,"成品鞋","止滑性试验:乾式0.5(含)以上;湿式0.3(含以上)","ˇ","ˇ","ˇ","ˇ","ASTM-F1677(可依据需求增加)"
36,,"耐磨耗:150mm3(含)以下","ˇ","ˇ","ˇ","ˇ","DIN53516. (可依据需求增减) "
37,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
38,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每"
,," 10公分需有10针(含)以上. "
39,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案"
,," ,文字批号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
,,"3. 贴有经济部标准检验局授权之合格认证标签;或通过ISO9000国际品质认证或是通过经济部标准检"
,," 验局安全鞋产品登录认证."
40,"验收","1. 规范表第37,38,39项由适用机关以目视检查办理. "
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制"
,," 造厂之检验报告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验合"
,," 格其费用由适用机关负担,如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数"
,," 量在500双(含)以上,适用机关得选择(1)制造厂检验报告或(2)制造厂送交具公信力第三者检验单"
,," 位(如经济部标准检验局,鞋类暨运动休闲科技研发中心等),得会同立约商代表依"
,," CNS2779 Z4006(计数值检验程序及抽样表)(采用S-1特殊检验水准,以双为单位,允收水准AQL为"
,," 4%),办理抽样及检验,检验费用由立约商负担."
"第10组海巡勤务工作鞋"
"第10组;第页;共页"
"第10组:海巡勤务工作鞋采购规范表"
"项目",,,"第1项","第2项","第3项","检验方法"
"规格"
1,"鞋面","材质:","牛皮","珠面牛皮(防泼水处理)","光面黄牛珠面皮","材质分析"
2,,"厚度:1.5mm(含)以上","ˇ","ˇ","ˇ","CNS 1274"
3,,"抗拉强度:__ kgf/cm2(含)以上",120,120,120,"CNS 1278"
4,,"撕裂强度:__ kgf/mm(含)以上",3,3,3,"CNS 1279"
5,,"破裂强度:__ kgf/cm2(含)以上",25,25,35,"CNS 1353"
6,"内里","材质:","(1)透气细布 (2)防水透气膜 (3)透气泡绵 (4)纺织品","0.8mm以上牛皮","0.6~1.0mm牛皮全里","材质分析,厚度CNS1274"
7,"中底","材质:","皮克隆","中底纸浆版","纸浆定型中底,中置铁心","材质分析"
8,"鞋垫","发泡材料+抗菌布料(无细菌滋生)","ˇ","ˇ","ˇ","材质分析 抗菌性能-AATCC 147:1998 金色葡萄球菌 ATCC 6538P"
,,"防霉(1级) 纺织品+吸震垫+EVA边墙脚杯","-","-","ˇ","防霉性试验-白癣菌 ASTM G21-96 ATCC 9533"
9,"鞋底","材质:","耐油橡胶±10%以下,加上EVA,双密度成型,重量超轻,软,耐电压3300伏特","橡胶","耐油橡胶±10%以下+防印记(4级)","放大镜分析 耐油-CNS 6863,IRM#903 23±2℃×22hrs 不留痕迹试验-4级 灰色标比对"
10,"鞋底","抗拉强度:__kgf/cm2(含)以上",120,120,120,"CNS3553,2型试片"
11,,"撕裂强度:__kgf/cm(含)以上",35,35,35,"CNS3559,B型试片"
12,,"延伸率: %(含)以上",350,350,350,"CNS3553,2型试片"
13,,"耐磨:损失量____mm3(含)以下",200,200,200,"DIN 53516"
14,,"止滑系数:乾式__(含)以上",0.8,0.8,"0.8","ASTM-F1677"
,,"止滑系数:湿式__(含)以上",0.5,0.5,0.5
15,"耐挠性","__次不生龟裂",40000,40000,40000,"SATRA TM77 弯曲角度600"
16,"制造方式",,"加州作法C式成型;高温高压成型绝不脱胶","鞋面与鞋底采胶著黏合+大底车缝","固特异(G式)","制造种类判定"
17,"要求事项",,"-","-","1,黑色半高筒款系带式,成品完整并附鞋带2条. 2,鞋面与鞋身车缝部分以30番进口尼龙车缝,车缝针距每10公分约32针(含)以上.","游标卡尺"
18,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
19,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每10公分需有"
,," 10针(含)以上. "
20,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案,文字批"
,," 号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
,,"3. 删除"
21,"验收","1. 规范表第18,19,20项由适用机关以目视检查办理. "
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制造厂之检"
,," 验报告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验合格其费用由适用机"
,," 关负担,如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数量在500双(含)以上,适用机"
,," 关得选择(1)制造厂检验报告或(2)制造厂送交具公信力第三者检验单位(如经济部标准检验局,鞋类暨运动"
,," 休闲科技研发中心等),得会同立约商代表依CNS2779 Z4006(计数值检验程序及抽样表)(采用S-1特殊检验"
,," 水准,以双为单位,允收水准AQL为4%),办理抽样及检验,检验费用由立约商负担."
,," "
"第11组伞兵长统皮鞋"
"第11组;第页;共页"
"第11组伞兵长统皮鞋采购规范"
"第1项:伞兵长统皮鞋-固特异底",,,,,,"第2项:伞兵长统皮鞋-橡胶注射底"
"编号:MPC-S-304-00013F(原编号:MPC-304-033E)"
"1.适用范围:本规格适用於陆军伞兵皮鞋检验用"
"2.适用资料:(本节说明规格制订时所适用之规格标准)"
" 2-1中华民国国家标准"
" CNS2779Z4006 计数值检验抽样程序及抽样表"
" CNS734K6047 橡胶磨耗试验标准"
" CNS3555K6346 硫化或热塑性橡胶硬度试验法"
" CNS3553K6344 硫化橡胶拉伸试验法"
" CNS 3689 Z 7043 第6.4.1节 中国国家标准之程式"
" CNS3556K6347 硫化橡胶老化试验法"
" CNS6863Z2029 皮革制安全鞋."
" CNS4799S1092 橡胶底帆布皮鞋及全橡胶之标准铸模尺度"
" CNS4801S1094 皮鞋楦头之标准尺度"
" 2-2国军军品规格"
" CMS-P-050001 面皮"
" CMS-C-050006 皮鞋里皮"
"3.品质要求:"
" 3-1成品构造须符合军品确样样品规定."
" 3-2鞋面之缝制须良好,线路整齐,无歪斜,跳针,漏缝及断裂等现象,针码每3公分8-12针,各部线"
" 头长度不得超过0.3公分."
" 3-3鞋面面皮须光亮均匀,无破损,刀伤,烫伤,碰伤,筋疤,麻点,脏污,沾胶及发霉等不良现象."
" 3-4鞋内不得留有钉子等异物."
" 3-5鞋面上梆须端正不得左右歪斜0.5公分以上. "
" 3-6双鞋后部高度相差不得超过0.5公分以上. "
" 3-7鞋眼须扎实紧密,无脱落,变形或缺件."
" 3-8鞋内中底须平整无鼓起现象."
" 3-9每双成品以一双鞋带连接系好."
" 3-10每只成品鞋,鞋内须塞入纸团,不得少於三张."
" 3-11每双成品鞋装入小纸盒,须每单脚以塑胶袋包装,并置入1公克乾燥剂一包."
" 3-12成品鞋后踵须平整."
" 3-13鞋底车沿条应扎实紧密,针码每5公分7-9针(固特异贴底)."
" 3-14鞋垫须贴正,贴牢,裁制大小适中,不得有过大皱摺或过小未覆盖中底之现象."
" 3-15鞋底与鞋面粘合需紧密,不得有脱胶开缝,齿角凹凸及鞋面皱摺之现象."
" 3-16每双鞋须吊挂保养使用须知,外盒并标示型号并置入纸撑及隔板."
" 3-17注射鞋底应无显著气泡,杂物等现象,每只鞋底缺胶部分,面积超过0.5X0.5平方公分者不得超过"
" 3处,外底边缘应修剪整齐,鞋底与鞋面接合处胶边余胶部分长度或高度不得超过0.5公分."
" 3-18上胶部份应均匀,且刷胶高度不得超过0.5公分."
"4.批之组成:"
" 本规格所谓之批量系指在同生产工厂,在同一规格,同一时期,同一制程下之产量(最大批量50000"
" 双)."
"5.抽样与检验:"
" 5-1抽样:"
" 5-1-1外观及包装抽样依CNS2779Z4006实施抽样,使用一般检验水准I级,正常单次抽样计画."
" 5-1-2尺寸检验抽样:各型号依合约批量抽取(如鞋楦抽样表),其中1双尺寸不符即全批判定不合"
" 格;尺寸要求如表2."
,,"鞋楦抽样表","批量(双)",,"抽样数(每型号)"
,,,"1~3000",,"1双"
,,,"3001~6000",,"2双"
,,,"6001以上",,"5双"
" 5-1-3物性检验抽样:依CNS2779Z4006实施抽样,使用特殊检验水准S-1级,单次抽样计画,AQL"
" 4.0%抽样计画."
" 5-2检验:"
" 5-2-1外观及包装检验:严重疵病其中1项疵病即全批判定不合格,主要疵病AQL6.5%,次要疵病"
" AQL10%(详如下表)"
"严重疵病","1.型号不符.",,,,,,"目视检查"
,"2.鞋内有U型钉等异物.",,,,,,"目视检查"
,"3.鞋面破损,刀伤不良现象.",,,,,,"目视检查"
"主要疵病","1.后踵不平整.",,,,,,"目视检查"
,"2.鞋面上梆歪斜,齿角凹凸及鞋面皱摺之现象.",,,,,,"目视检查"
,"3.砸眼不牢,歪斜,脱落,缺件.",,,,,,"目视检查"
,"4.鞋垫未贴正,贴牢,裁制大小不适中,有过大皱摺或过小未覆盖中",,,,,,"目视检查"
," 底之现象."
,"5.鞋面与鞋底粘合不良,有脱胶开缝之现象.(宽度或深度超过1公分 ",,,,,,"目视及量尺检查"
," 含以上)"
,"6.鞋面有烫伤,碰伤,麻点,发霉及筋疤等不良现象.",,,,,,"目视检查"
,"7.胶底缺胶,不熟鼓起,表面不平整或成海绵状,脱跟,脱底(橡胶注",,,,,,"目视检查"
," 射成型)."
"次要疵病A级","1.沿条车外线针码每5公分不足7~9针.(固特异贴底)",,,,,,"量尺量测"
,"2.鞋面缝线针码不对,歪斜,跳针,漏缝,断裂等不良现象.",,,,,,"目视检查"
,"3.车沿条针码每5公分7-9针.",,,,,,"量尺量测"
,"4.鞋垫及中底不平整,有鼓起现象.",,,,,,"手触及量尺检查"
,"5.鞋面脏污,沾胶.",,,,,,"目视检查"
,"6.鞋面与鞋底粘合不良,有脱胶开缝之现象.(宽度或深度小於1公分)",,,,,,"目视及量尺检查"
,"7.鞋面烫伤或经整烫后留有明显刷痕,未恢复鞋面之亮度.",,,,,,"目视检查"
,"8.刷胶高度超过0.5公分",,,,,,"卡尺量测"
"次要疵病B级","1.双鞋后部高度相差不得超过0.5公分以上. ",,,,,,"量尺量测"
,"2.各部线头长度不得超过0.3公分. ",,,,,,"量尺量测"
,"3.未系鞋带或未吊挂保养使用须知.",,,,,,"目视检查"
,"4.鞋内未塞入纸团及少於三张薄纸片.",,,,,,"目视检查"
,"5.成品鞋装入小纸盒未以塑胶袋包装.",,,,,,"目视检查"
,"6.塑胶袋内未装入1公克乾燥剂.",,,,,,"目视检查"
" 5-2-1-1检验扣点标准:"
" 5-2-1-1-1 1个主要疵病扣1点,2个次要疵病A级扣1点,3个次要疵病B级扣1点,同1双成品鞋最多"
" 扣1点."
" 5-2-1-1-2 同1双成品鞋有1个以上主要疵病,折算扣1点,或有2个以上次要疵病A级或有3个以上次"
" 要疵病B级,折算扣1点."
" 5-2-1-1-3若在不同成品鞋上,其所有疵病数累加计算."
" 5-2-2尺寸检验:依合约委制各型号数量抽取,其中1双尺寸不符即全批判定不合格:尺寸要求如表"
" 2."
" 5-2-3物性检验:物性检验需符合物性要求表1."
" 5-2-4检验方法(半成品):"
" 5-2-4-1固特异橡胶大底试片及橡胶射出底试片:"
" 5-2-4-1-1硬度:依CNS3555K6346法检验之(A型硬度计量测)."
" 5-2-4-1-2伸长率:依CNS3553K6344第3号试验片测试之."
" 5-2-4-1-3抗拉强度:依CNS3553K6344第3号试验片测试之."
" 5-2-4-1-4耐磨性:依CNS734K6047法,磨角15度,荷重2磅检验之."
" 5-2-4-1-5老化试验(橡胶注射底适用):依CNS3556K6347中「空气加热老化试验」(常态烘箱法"
" )规定,先将试样以70±3℃做连续加速老化120小时后再依前项第(5-2-4-1-3)节同方"
" 法测定其抗拉强度,并计算老化处理前后之变化率."
" 5-2-5成品检验方法:"
" 5-2-5-1固特异贴底成型剥离力试验:依CNS6863Z2029第8.3节检验之."
" 5-2-5-2成品橡胶注射成型剥离力:先将面皮及后跟割开取下,再自鞋尖中心切割至后踵,将鞋切"
" 成两半作成两样条(不可破坏任何胶底与面皮粘合部分);并将中底清理乾净(避免影响测试"
" 之精密度)再任意取其一样条一端,剥离约40㎜长后,剥离两端分别夹於拉力试验机上,以"
" 每分钟200㎜±2㎜之拉速拉之,取记录值较高一端波状各顶点之胶著荷重之平均值即为剥离"
" 力需符合表2之要求."
" 5-2-5-3成品铁钉穿透性试验:依CNS6863Z2029第8.8节方法检验.(以100公斤静载重10秒,检查"
" 铁钉是否贯穿鞋底;若无加钢片则免验)."
" 5-3但书:1.本项产品(半成品)於进料时检测,成品鉴测时5-2-4-1-1硬度,5-2-4-1-2伸长率,"
" 5-2-4-1-3抗拉强度,5-2-4-1-4耐磨性及5-2-4-1-5老化试验不再实施,惟需提供合格之"
" 进料检验纪录备查."
" 2.半成品之获得方式属於采购行为者依采购权责办理."
" 3.本项成品「铁钉穿透性」试验,视委制单位需求办理."
"6.包装与标志:"
" 6-1包装:同批量之包装数须一致(每箱不得超出10双;零头数另行包装),另每双装入小纸盒平放,"
" 小纸盒外标示型号及批号."
" 6-2标志:每个纸箱外面须注明品名,颜色,型号,批号,数量,单位,包装重量,出厂日期,制补"
" 单位及保固年限(含储存及穿著使用年限):2年,每只鞋鞋舌内面须盖印型号及批号."
"7.附表(图)成品图示:(图示仅供参考,依军种确样之样品为主) "
" "
"表1,物性要求表"
"固特异贴底","硬度",,,,"75±5(A型硬度计测量)"
,"伸长率",,,,"310%以上"
,"抗拉强度",,,,"105公斤/平方公分以上"
,"耐磨性",,,,"0.35立方公分/2000转以下(磨角15度,荷重2磅)"
,"成品剥离力(鞋面与大底间)",,,,"20公斤以上(全鞋底剥离)"
"橡胶注射底","硬度",,,,"65±5 (A型硬度计测量)"
,"伸长率",,,,"400%以上"
,"抗拉强度",,,,"140公斤/平方公分以上"
,"耐磨性",,,,"0.35立方公分/2000转以下"
,,,,,"(磨角15度,荷重2磅)"
,"老化试验",,,,"抗拉强度降低率25%以下"
,"成品剥离力(鞋面与大底间)",,,,"5公斤以上(鞋底单边剥离)"
"成品耐铁钉穿透性",,,,,"100㎏鞋底不得贯穿"
"表2,鞋楦尺寸表 "
"备注","1.单位:㎜,公差±2㎜ ",,,,"(1)底长"
,"2.底长依CNS4799S1092法,量测由A点至B点之楦头底面之长度. ",,,,,"A"
,"3.楦头周径尺度依CNS4801S1094法,量测由B点绕鞋面经过C点再回至B点,测定其距离."
,"4.型号未明订之底长尺寸则依比例大小级放. ",,,,,"B"
," ",,,,"(2)楦头周径 "
," "
"共6页第3页"
"第12组女官士皮鞋"
"第12组;第页;共页"
"第12组女官士高跟,平跟皮鞋采购规范"
"第1项:女官士高跟鞋",,,,,,"第2项:女官士平跟鞋"
"编号:MPC-S-203-00073H(原编号:MPC-S-304-00014G)"
"1.适用范围:本规格适用於各款(高,低跟及平底)三军女性军士官及员工皮鞋检验用."
"2.适用资料:(本节说明规格制订时所适用之规格标准)"
" 2-1中华民国国家标准"
" CNS2779Z4006 计数值检验抽样程序及抽样表"
" CNS734K6047 橡胶磨耗试验标准"
" CNS3555K6346 硫化或热塑性橡胶硬度试验法"
" CNS3553K6344 硫化橡胶拉伸试验法"
" CNS3689Z7043 第6.4.1节 中国国家标准之程式"
" CNS4869S1096 鞋用橡胶底"
" CNS742S2009 运动鞋类检验法"
" CNS4801S1094 皮鞋楦头之标准尺度"
" 2-2美国测试与材料学会(ASTM)标准"
" ASTM D1894 止滑性试验法"
" 2-3国军军品规格"
" CMS-P-050025 女用鞋面皮"
" CMS-C-2046a 猪(面)里皮"
" CMS-C-1180b 鞋用人造衬料"
"3.品质要求:"
" 3-1原料要求:"
" 3-1-1鞋面皮:需符合CMS-P-050025各项要求."
" 3-1-2鞋里皮:需符合CMS-C-2046a猪面皮各项要求."
" 3-1-3港宝:需符合CMS-C-1180b 1.3 mm人造衬料各项要求."
" 3-1-4鞋底:需符合3.2.3物性各项要求."
" 3-2成品要求:"
" 3-2-1工艺,外观及包装:符合第4.3.1节所列各项疵病允收值要求."
" 3-2-2尺寸:符合表1之尺寸要求."
"表1:尺寸要求表 橡胶鞋底尺寸要求表 型号 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 长度 233 237 240 243 246 250 253 256 260 263 266 270 273 276 279 PCU鞋底尺寸要求表 型号 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 长度 218 222 226 230 234 238 242 246 250 254 258 262 266 270 274 备注 一.长度以楦头长度量测,量测方法:依CNS4801S1094法执行. 二.单位:公厘,公差为 2公厘. 三.表内未订型号,其尺寸要求按长度级放比例制作. 四.后跟高度(含天皮):(每双成品后跟高度公差为 1/16吋) (一)平底:1吋(不含)以下. (二)低跟:1吋(含)至1.5吋(不含). (三)高跟:1.5吋(含)以上. "
" 3-2-3物性:符合表2之物性要求."
"表2:物性要求表 橡胶鞋底 硬度 70±5(A型硬度计测量) . 伸长率 250%以上. 抗拉强度 120公斤/平方公分以上. 耐磨性 0.40立方公分/2000转以下(磨角15度,荷重2磅). 成鞋胶著力(鞋底与鞋面间) 7公斤以上. 成鞋止滑效果量测 测试厚度须为2.5㎜以上. PCU鞋底 弯曲试验 试验鞋面与大底间5万次不得有开缝之现象. 止滑性试验(静摩擦系数) 乾 式 0.5以上. 湿 式 0.4以上."
"4.品质保证及检验:"
" 4-1品保规定:"
" 4-1-1检验权责:如合约上无其他规定,由规格鉴测中心实施成品抽样检验,检验纪录应保持完整 ,以备有关上级谘询及查验."
" 4-1-2产品品鉴:制供商应提供下列资料:"
" 4-1-2-1产品零件(原料)检验报告单."
" 4-1-2-2军品合格保证单."
" 4-2检验规定:"
" 4-2-1产品之批量:本规格所谓之批量系指在同生产工厂,在同一规格,同一时期,同一制程下之 产量(最大批量10000双). 4-2-2抽样: 4-2-2-1工艺,外观及包装:抽样依CNS2779Z4006实施抽样,使用一般检验水准I级,正常单次抽样 计画. 4-2-2-2尺寸检验抽样:各型号依合约批量抽取(如鞋楦抽样表),其中1双尺寸不符即全批判定不 合格."
,,"鞋楦抽样表","批量(双)",,"抽样数(每型号)"
,,,"1~3000",,"1双"
,,,"3001~6000",,"2双"
,,,"6001以上",,"5双"
" 4-2-2-3物性检验抽样:依CNS2779Z4006实施抽样,使用特殊检验水准S-1级,单次抽样计画 AQL4.0%."
" 4-3检验:"
" 4-3-1工艺,外观及包装检验:依据下表所列之疵病分类及检验方法进行检验,其中严重疵病只要1项即全批判定不合格;而主要疵病AQL6.5%,次要疵病AQL10%,并依表后所列扣点标准计算之."
,"严重疵病","1.型号不符",,,,,"目视检查"
,,"2.鞋内有U型钉等异物",,,,,"目视检查"
,,"3.鞋跟大底应接(贴)合欠牢固,有松动及歪斜之现象.",,,,,"目视检查"
,,"4.鞋面破损,刀伤",,,,,"目视检查"
,,"5.成品构造未符合确样样鞋规定",,,,,"目视检查"
,"主要疵病","1.鞋面与鞋底贴合不正有歪斜现象.",,,,,"目视检查"
,,"2.鞋面与鞋底粘合不良,有脱胶开缝3现象(宽度或深度超过1公分含以上)",,,,,"目视及量尺"
,,"3.鞋面烫伤,碰伤,烙印及麻点",,,,,"目视检查"
,,"4.港宝(热熔胶片)歪斜,变形及结梆后痕迹外显",,,,,"目视检查"
,,"5.鞋面上梆歪斜有凹凸及齿角等不良现象",,,,,"目视检查"
,"次要疵病A级","1.鞋面缝制针码每公分4-6针",,,,,"量尺量测"
,,"2.线头长度超过0.3公分",,,,,"量尺量测"
,,"3.鞋面缝制线路起皱,歪斜,跳针,漏缝",,,,,"目视检查"
,,"4.成品左右鞋高度超过0.3公分",,,,,"量尺量测"
,,"5.成品磨粗高度超出0.3公分以上或未烫平整,或喷漆不均匀",,,,,"目视及量尺检查"
,,"6.鞋面与鞋底粘合不良,有脱胶开缝之现象(宽度或深度小於1公分)",,,,,"目视及量尺检查"
,"次要疵病 B级","1.鞋垫贴合不平整,有过大浮鼓或过小未覆盖中底之现象",,,,,"目视检查"
,,"2.包装与第5-1节规定不符",,,,,"目视检查"
,,"3.标示与第5-2节规定不符",,,,,"目视检查"
,,"4.鞋面有筋疤,皱摺现象",,,,,"目视检查"
,,"5.上胶部分不均或刷胶高度超过0.3公分",,,,,"目视检查"
,,"6.鞋面各部位(含内里)有沾胶,发霉,污染不洁等现象",,,,,"目视检查"
"※疵病检验扣点标准:"
" (1)成品鞋中之1个主要疵病扣1点,2个次要疵病A级扣1点,3个次要疵病B级扣1点,同1双成品鞋最 多扣1点."
" (2)若疵病出现在不同成品鞋上,则其所有疵病数累加计算."
" 4-3-2尺寸检验:依合约委制各型号数量抽取,其中1双尺寸不符即全批判定不合格:尺寸要求如表1."
" 4-3-3物性检验:"
" 4-3-3-1橡胶鞋底试片: 4-3-3-1-1硬度:依CNS3555K6346法检验之(A型硬度计量测). 4-3-3-1-2伸长率:依CNS3553K6344第3号试验片测试之. 4-3-3-1-3抗拉强度:依CNS3553K6344第3号试验片测试之. 4-3-3-1-4耐磨性:依CNS734K6047法,磨角15度,荷重2磅检验之. 4-3-3-1-5成鞋胶著力试验:依CNS 742 S 2009第16.1节检验之. 4-3-3-1-6成鞋止滑效果量测:依CNS4869S1096第4.1节检验之. 4-3-3-2 PCU鞋底: 4-3-3-2-1成鞋弯曲试验:取试样二双,后跟及前掌部份分别固定於鞋子弯曲试验机上,调整机器前 掌板动角度40～50度,速度为每分钟100～105次,注意沿条与鞋底间是否 有脱开或任何龟裂现象. 4-3-3-2-2成鞋止滑性试验(静摩擦系数) :依ASTM D1894法检验之."
"5.包装及标志:"
" 5-1包装:同批量之包装数须一致(每箱不得超出20双;零头数另行包装),小纸盒外标示型号及批号 及盒内置入立可擦(马上亮皮革油);每只鞋置入1公克乾燥剂再装入透明塑胶袋或不织布鞋 袋. 5-2标志:每个纸箱外面须注明品名,合约案号,型号,数量,包装重量,包装日期,制补单位及每只 鞋内侧腰及每个纸箱外须盖印批号,型号."
"6.备注:"
" 6.1成品图示:(图示仅供参考,依军种确样之样品为主)"
"第13组陆,空军飞行皮靴"
"第13组;第页;共页"
"第13组陆,空军飞行皮靴采购规范"
"第1项:陆军飞行皮靴-PU射出底",,,,,,"第4项:空军新式飞行皮靴-PU射出底"
"第2项:陆军飞行皮靴-橡胶射出底",,,,,,"第5项:空军新式飞行皮靴-橡胶射出底"
"第3项:陆军飞行皮靴-固特异贴底",,,,,,"第6项:空军新式飞行皮靴-固特异贴底"
"编号:MP-304-065A"
"1.适用范围:本规格适用於飞行靴检验用."
"2.适用资料:"
" 2-1材料规格"
" CMS-C-050001 面皮"
" CMS-C-02046a 猪面(里)皮"
" CMS-P-050006 皮鞋里皮"
" CMS-P-050017 鞋用汽眼"
" CMS-C-01144c 人造中底(加纱布)(PU注射)"
" CMS-C-1928a 皮浆中底(橡胶注射)"
" MP-304-019B 皮革拉鍊盘"
" 2-2中国国家标准"
" CNS2779Z4006 计数值检验抽样程序及抽样表"
" CNS734K6047 橡胶磨耗试验标准"
" CNS3555K6346 硫化或热塑性橡胶硬度试验法"
" CNS3553K6344 硫化橡胶拉伸试验法"
" CNS 3689 Z 7043 第6.4.1节 中国国家标准之程式"
"3.品质要求:"
" 3-1成品构造须符合样鞋规定,各项材料检测纪录需备查."
" 3-2鞋面之缝制须良好,线路整齐,无歪斜,跳针,漏缝,脱线,浮线及断线等不良现象,针码每3公"
" 分8-10针,各部线头长度不得超过0.3公分."
" 3-3鞋面面皮须光亮均匀,无破损,刀伤,烫伤等不良现象."
" 3-4鞋底车沿条应扎实紧密,针码每5公分8-10针(固特异贴底);如为注射鞋底应无显著气泡,杂物"
" 等现象,每只鞋底缺胶部分,面积超过0.5X0.5平方公分者不得超过3处,外底边缘应修剪整齐,鞋"
" 底与鞋面接合处胶边余胶部分长度或高度不得超过0.5公分."
" 3-5鞋内不得留有U型钉等异物."
" 3-6鞋面(含后踵部位)上梆须端正,圆顺,不得歪斜及凹凸,齿角等钳帮不良之现象."
" 3-7成品左右鞋高度差异不得超过0.5公分."
" 3-8上胶部分应均匀,且刷胶高度不得超过0.3公分."
" 3-9鞋眼须扎实紧密,无脱落,变形,不牢或缺件."
" 3-10鞋垫须平正贴合,不得有脱落之现象,且裁制大小适中,无皱摺或过小未覆盖中底之现象."
" 3-11每双成品须置入皮革拉鍊盘乙付於包装纸盒内(如军种未要求配置免验)."
" 3-12成品皮革拉链盘须以牛面皮缝合10号古铜拉链或6.5吋黑塑钢拉鍊,缝线针码每3公分8-10针,线"
" 路应整齐,无歪斜,跳针,漏缝,脱线,浮线及断线等不良现象."
" 3-13每双鞋须吊挂保养使用须知,外盒并标示型号并置入纸撑及隔板. "
" 3-14每双港宝须端正置入,不得歪斜,变形塌陷之现象."
" 3-15内里应缝制(贴合)平整牢固,不得有脱开之现象"
" 3-16成品磨粗高度不得超出0.3公分(含)以上(低於0.3公分须整烫平整,喷漆均匀)."
" 3-17成品余胶胶边高度不得超出0.5公分(含)以上."
" 3-18前头须车缝外线一道(本项适用於固特异飞行靴)"
" 3-19鞋面与鞋底间粘合牢固,不得有脱胶开缝之现象."
"4.批之组成:"
" 本规格所谓之批量系指在同一生产工厂,在同一规格,同一时程,同一制程下之产品(最大批量为"
" 10000双)."
"5.抽样与检验:"
" 5-1抽样:"
" 5-1-1外观及包装抽样:依CNS2779 Z 4006实施抽样,使用一般检验水准一级,正常单次抽样计画抽样."
" 5-1-2尺寸检验抽样:依合约委制各型号数量抽取(如鞋楦抽样表),其中1双尺寸不符即全批判定不"
" 合格:尺寸要求如表1."
,,"鞋楦抽样表(每型号)"
,,"批量(双)",,"抽样数"
,,"1~3000",,"1双"
,,"3001~6000",,"2双"
,,"6001以上",,"5双"
" 5-1-3物性检验抽样:依CNS2779Z4006实施抽样,使用特殊检验水准S-1级,正常单次抽样计划,AQL"
" 4.0%抽样计划表."
" 5-2检验:"
" 5-2-1外观及包装检验:严重疵病其中1项疵病即全批判定不合格,主要疵病AQL6.5%,次要疵病AQL"
" 10%(详如下表)"
,"严重疵病","1.型号不符.",,,,,,"目视检查"
,,"2.鞋内U型钉未拔除.",,,,,,"目视检查"
,,"3.成品外观须符合军种确样样鞋.",,,,,,"目视检查"
,,"4.鞋面破损.",,,,,,"目视检查"
,,"5.前头未车缝外线一道(固特异飞行靴).",,,,,,"目视检查"
,"主要疵病","1.皮革拉链盘未以牛面皮缝合10号古铜拉鍊或6.5吋黑塑钢拉",,,,,,"目视检查"
,," 鍊,缝线针码未能每3公分8-10针,线路歪斜,跳针,漏"
,," 缝,脱线,浮线及断线等不良现象."
,,"2.鞋面及后踵上梆歪斜有凹凸,齿角等钳帮不良之现象.",,,,,,"目视检查"
,,"3.鞋面前,后包刀伤致鞋面损伤.",,,,,,"目视检查"
,,"4.包装与标志不符.",,,,,,"目视检查"
,,"5.胶底缺胶,不熟鼓起,表面不平整或成海绵状,脱跟,脱",,,,,,"目视检查"
,," 底(橡胶注射成型)."
,,"6.鞋面与鞋底间粘合不良,有脱胶开缝之现象(宽度或深度",,,,,,"目视及量尺检查"
,," 超过1公分含以上)."
,"次要疵病A级","1.刷胶高度超过0.3公分.",,,,,,"量尺检查"
,,"2.鞋面喷漆未均匀光亮.",,,,,,"目视检查"
,,"3.砸眼不牢,歪斜,脱落,缺件.",,,,,,"目视检查"
,,"4.鞋面缝线针码不正确,线路歪斜,跳针,漏缝,脱线,浮",,,,,,"目视及量尺检查"
,," 线及断线等不良现象,针码每3公分8-10针."
,,"5.车沿条针码每5公分8-10针.",,,,,,"目视检查"
,,"6.港宝未端正置入,有歪斜,变形塌陷之现象.",,,,,,"目视检查"
,,"7.鞋面脏污,沾胶,发霉.",,,,,,"目视检查"
,,"8.缝线处未烧断,线头过长,超过0.3公分.",,,,,,"目视检查"
,,"9.鞋面前,后碰伤及刮伤致鞋面损伤.",,,,,,"目视检查"
,,"10.鞋面与鞋底间粘合不良,有脱胶开缝之现象(宽度或深度",,,,,,"目视及量尺检查"
,," 小於1公分)."
,"次要疵病B级","1.左右鞋高相差超过0.5公分.",,,,,,"量尺检查"
,,"2.鞋底与鞋面接合处胶边余胶部分长度或高度超过0.5公分(",,,,,,"目视及量尺检查"
,," 含)以上."
,,"3.磨粗高度过高,超过0.3公分(含)以上(低於0.3公分须",,,,,,"目视及量尺检查"
,," 整烫平整,喷漆均匀)."
,,"4.鞋垫贴合不平整,有脱落及过大浮鼓或过小未覆盖中底之",,,,,,"目视检查"
,," 现象."
,,"5.内里缝制(贴合)不平整牢固,有脱开之现象.",,,,,,"目视检查"
,,"6.未系(或未置入)皮革拉鍊盘及鞋带或未吊挂保养使用须知",,,,,,"目视检查"
,,"7.每双飞行靴未置入纸撑及隔板.",,,,,,"目视检查"
" 5-2-1-1检验扣点标准:"
" 5-2-1-1-11个主要疵病扣1点,2个次要疵病A级扣1点,3个次要疵病B级扣1点,同1双成品鞋最多扣1点"
" ."
" 5-2-1-1-2同1双成品鞋有1个(含)以上主要疵病,折算扣1点,或有2个(含)以上次要疵病A级或有3"
" 个(含)以上次要疵病B级,折算扣1点."
" 5-2-1-1-3若在不同成品鞋上,其所有疵病数累加计算."
" 5-2-2尺寸检验:依合约委制各型号数量抽取,其中1双尺寸不符即全批判定不合格:尺寸要求如表1."
" 5-2-3物性检验:物性检验需符合物性要求表2."
" 5-2-4检验方法(半成品):"
" 5-2-4-1 PU大底试片及橡胶大底试片:"
" 5-2-4-1-1硬度:依CNS3555K6346法检验之(A型或E型硬度计量测)."
" 5-2-4-1-2伸长率:依CNS3553K6344第3号试验片测试之."
" 5-2-4-1-3抗拉强度:依CNS3553K6344第3号试验片测试之."
" 5-2-4-1-4耐磨性:依CNS734K6047法,磨角15度,荷重2磅检验之."
" 5-2-4-1-5老化试验(橡胶鞋底适用):依CNS3556K6347中「空气加热老化试验」(常态烘箱法)规定"
" ,先将试样以70±3℃做连续加速老化120小时后再依前项第(5-2-4-1-3)节同方法测定其抗"
" 拉强度,并计算老化处理前后之变化率."
" 5-2-5成品检验方法:"
" 5-2-5-1固特异贴底成型剥离力试验:依CNS6863Z2029第8.3节检验之."
" 5-2-5-2成品橡胶注射成型剥离力:先将面皮及后跟割开取下,再自鞋尖中心切割至后踵,将鞋切成两"
" 半作成两样条(不可破坏任何胶底与面皮粘合部分);并将中底清理乾净(避免影响测试之精密"
" 度)再任意取其一样条一端,剥离约40㎜长后,剥离两端分别夹於拉力试验机上,以每分钟"
" 200㎜±2㎜之拉速拉之,取记录值较高一端波状各顶点之胶著荷重之平均值即为剥离力需符合"
" 表 2之要求."
" 5-2-5-3成品铁钉穿透性试验:依CNS6863Z2029第8.8节方法检验.(以100公斤静载重10秒,检查铁钉"
" 是否贯穿鞋底)."
" 5-3但书:1.本项产品(半成品)於进料时检测,成品鉴测时5-2-4-1 PU大底(试片)及橡胶大底(试"
" 片)检验不再实施,惟需提供合格之进料检验纪录备查."
" 2.半成品之获得方式属於采购行为者依采购权责办理."
" 3.本项成品「铁钉穿透性」试验,视委制单位需求办理."
"6.包装与标志:"
" 6-1包装:同批量之包装数须一致(每箱不得超出10双;零头数另行包装)另每双装入小纸盒平放,小"
" 纸盒外须标示型号."
" 6-2标志:每个纸箱外面须注明品名,颜色,型号,批号,数量,单位,包装重量,出厂日期,制补单"
" 位及保固年限(含储存及穿著使用年限):2年,若产品属PU注射成型鞋底,须於每个纸盒"
" ,纸箱外注明「PU鞋底,请於出厂日期后半年内拨发使用」,每只鞋鞋舌内面须盖印型号及"
" 批号."
"7.附表(图) "
,"表1,尺寸要求表:"
,"表2,物性要求表:"
,"PU射出底","硬度",,,"75±5 (E型硬度计测量)"
,,"抗拉强度",,,"30公斤/平方公分(含)以上"
,,"伸长率",,,"300%(含)以上"
,,"耐磨性",,,"0.45立方公分/2000转(含)以下(磨角15度,荷重2磅)"
,"橡胶射出底","硬度",,,"65±5 (A型硬度计测量)"
,,"抗拉强度",,,"140公斤/平方公分(含)以上"
,,"伸长率",,,"400%(含)以上"
,,"耐磨性",,,"0.35立方公分/2000转(含)以下(磨角15度,荷重2磅)"
,,"老化试验",,,"抗拉强度降低率25%以下"
,,"成品剥离力(鞋面与大底间)",,,"5公斤(含)以上(鞋底单边剥离)"
,"固特异贴底","硬度",,,"60±5 (A型硬度计测量)"
,,"抗拉强度",,,"100公斤/平方公分(含)以上"
,,"伸长率",,,"300%(含)以上"
,,"耐磨性",,,"0.35立方公分/2000转(含)以下(磨角15度,荷重2磅)"
,,"成品剥离力(鞋面与大底间)",,,"20公斤(含)以上(全鞋底剥离)"
,"成品铁钉穿透性试验",,,,"100㎏鞋底不得贯穿"
"共6页第2页"
"共6页第4页"
"前 包 "
"后 包 "
"第14组陆军仪队长统皮鞋"
"第14组;第页;共页"
"第14组陆军仪队长统皮鞋采购规范"
"第1项:陆军仪队长统皮鞋"
"编号:MPC-304-020E"
"1.适用范围:本规格适用於三军仪队皮鞋(胶底胶跟或皮底皮跟含天皮)检验用"
"2.使用材料:"
" 2-1面皮(CMS-C-02044)"
" 2-2纸浆中底(CMS-C-01144)"
" 2-3三股合纤线(CMS-C-01422)"
" 2-4缝线胶底含胶跟或缝线皮底皮浆跟含天皮(物性要求如表一)"
" 2-5各种材料检测记录需备查"
"3.品质要求:"
" 3-1鞋面,鞋底,中底型号须一致,成品构造须符合样品规定."
" 3-2鞋面之缝制须良好,线路整齐,无歪斜,跳针,漏缝等现象,针码每公分3-4针,各部线头长度不"
" 得超过0.3公分,且缝线处须烧断."
" 3-3每双成品鞋装入小纸盒,须每只以塑胶袋包装,并罝入1公克乾燥剂一包及要领表."
" 3-4鞋面面皮须光亮均匀,无破损,刀伤,烫伤,碰伤,筋疤,麻点,烙印等不良现象."
" 3-5鞋内不得留有U型钉子等异物."
" 3-6鞋面上梆须端正不得歪斜±0.5公分."
" 3-7左右鞋高度相差应在0.5公分以内."
" 3-8上胶部份应均匀,且刷胶高度不得超过0.3公分."
" 3-9鞋眼须扎实紧密,无脱落,变形,不牢或缺件."
" 3-10鞋内鞋垫须平整,贴牢."
" 3-11每双成品以一双鞋带连接系好."
" 3-12鞋底车外线应扎实紧密,针码每5公分8~10针(另皮大底加贴橡胶底免验,且需加钉10根钉子)."
" 3-13后跟底部天皮须钉8~9根螺纹钉(依军种样品为准)."
" 3-14后跟垫须贴正,贴牢,裁制大小适中,不得有过大皱摺或过小未覆盖中底之现象."
" 3-15鞋面与鞋底贴合,不得有开口,漏缝等不良现象."
" 3-16每双热熔胶片(港宝)处须平整罝入,不得有歪斜,变形塌陷等不良现象."
" 3-17鞋面不得有沾胶,发霉,污染不洁等情形."
"4.批之组成:"
" 本规格所称之批量系指在同生产工厂,同一规格,同一时期,同一制程下之产量(最大批量10000双)"
"5.检验:"
" 5-1外观及包装检查:"
" 5-1-1抽样:依CNS2779Z4006实施抽样,使用一般检验水准一级,正常单次抽样计画,严重疵病:其"
" 中乙项疵病即判定不合格,主要疵病:AQL6.5%,次要疵病:AQL10%(详如下表)"
" 严重疵病",,"1.型号不符",,,,,"目视检查"
,,"2.鞋内钉子未拔除",,,,,"手触及目视检查"
"主要疵病",,"1.鞋面破损,刀伤,烫伤,筋疤,麻点,烙印等不良现象",,,,,"目视检查"
,,"2.鞋面上梆歪斜±0.5公分",,,,,"目视检查"
,,"3.后踵须平整",,,,,"目视检查"
,,"4.砸眼不牢,歪斜,脱落,缺件",,,,,"目视检查"
,,"5.后跟垫未贴正,贴牢,裁制大小不适中,有过大皱摺或过小未覆盖中底之现象",,,,,"目视检查"
,,"6.鞋面与鞋底贴合,有开口,漏缝等不良现象",,,,,"目视检查"
,,"7.每双热熔胶片(港宝)处未平整罝入,有歪斜,变形塌陷等不良现象",,,,,"目视检查"
,,"8.包装与标志及批号不符",,,,,"目视检查"
" 次要疵病A级",,"1.车外线针码每5公分8~10针(或皮大底加贴橡胶底未加钉十跟钉子)",,,,,"量尺及目视检查"
,,"2.缝线针码不对,线路歪斜,跳针",,,,,"目视检查"
,,"3.刷胶高度超过0.3公分",,,,,"量尺量测"
,,"4.鞋垫须平整,无鼓起现象",,,,,"手触及目视检查"
,,"5.后跟底部天皮未钉8~9根螺丝钉(依军种样品为准)",,,,,"目视检查"
,,"6.鞋面脏污,沾胶,发霉",,,,,"目视检查"
"次要疵病B级",,"1.左右鞋高度相差超过0.5公分",,,,,"量尺量测"
,,"2.线头过长超过0.3公分",,,,,"量尺量测"
,,"3.喷漆不均匀或光亮度不够",,,,,"目视检查"
,,"4.缝线处烧断",,,,,"目视检查"
,,"5.未系鞋带",,,,,"目视检查"
,,"6.未置入1公克乾燥剂或要领表",,,,,"目视检查"
" 5-1-2检验扣点标准:"
" 5-1-2-1一个主要疵病扣一点,二个次要疵病A级扣一点,三个次要疵病B级扣一点,同一双成品鞋"
" 最多扣一点."
" 5-1-2-2同一双成品鞋有一个(含)以上主要疵病,折算扣一点,或有二个(含)以上次要疵病A级"
" ,或有三个次要疵病B级,折算扣一点."
" 5-1-2-3若在不同成品鞋上,其所有疵病数累加计算."
" 5-2物性检验:"
" 5-2-1抽样:依CNS2779Z4006实施抽样,使用特殊检验水准S-1级,正常单次抽样计划,AQL10%抽样计"
" 划表,物性要求如表一."
" 5-2-2检验方法:"
" 5-2-2-1硬度:依CNS3555K6346法A型硬度计检验之."
" 5-2-2-2伸长率:依CNS3553K6344第3号试验片测试之."
" 5-2-2-3抗拉强度:依CNS3553K6344第3号试验片测试之."
" 5-2-2-4耐磨性:依CNS734K6047检验之,磨角15度,荷重2磅."
" 5-3尺寸检验:"
" 5-3-1抽样:於量产前依CNS2779Z4006实施抽样,量测鞋楦尺寸,使用特殊检验水准S-1级,单次抽样"
" 计划,AQL6.5%抽样计划表,尺寸要求如表二,产品鉴测时不再实施."
" 5-4但书:本项产品(半成品)於进料时检测,成品鉴测时5-2-2大底物性检验不再实施,惟需提供合"
" 格之进料检验纪录备查(惟外包产品之购料应送至军品鉴测处检验.有军品鉴测处之进料检"
" 验合格报告者,鉴测时就不再对原料进行检验;无军品鉴测处之进料检验合格报告者,鉴测"
" 时仍需由军品鉴测处依规格实施原料之检验."
"6.包装与标志:"
" 6-1包装:每箱装10双,每双装入小纸盒平放,小纸盒外须标示型号."
" 6-2标志:每个纸箱外面须注明品名,颜色,型号,批号,数量,单位,包装重量,出厂日期,制补单"
" 位及储存年限:二年,每只鞋鞋舌内面须盖印型号及批号."
"7.参考资料:"
" CNS2779Z4006 CMS-C-02044 CMS-C-01422 CMS-C-02044"
" CMS-C-01633 CNS3555K6346 CNS3553K6344 CNS734K6047"
"8.附表(图):"
"表一,物性要求表"
,"硬度",,,"75±5"
,"伸长率",,,"310%(含)以上"
,"抗拉强度",,,"105公斤/平方公分(含)以上"
,"耐磨性",,,"0.2立方公分/2000转(含)以下(磨角15度,荷重2磅)"
"表二,尺寸要求表"
"图一,成品图"
"第15组空军军乐队皮鞋"
"第15组;第页;共页"
"第15组空军军乐队皮鞋采购规范"
"第1项:空军军乐队半高统马靴-橡胶登山底",,,,,"第2项:空军军乐队半高统马靴-三合一组合底"
"编号:MP-304-038D"
"1.适用范围:本规格适用於双拉鍊半高统马靴(登山底或皮大底)及军乐队半高统马靴("
" 三合一组合底或皮大底)检验用."
"2.使用材料:(本节说明制作时所用之主要材料及规格)"
" 2-1面皮(CMS-C-02044b)或可丽柔漆皮(CMS-C-02021)"
" 2-2猪面里皮(CMS-C-02046a)"
" 2-3纸浆中底(CMS-C-01144c)"
" 2-4黄牛底皮(CMS-C-00708)"
" 2-5橡胶登山鞋底或三合一组合底(物性要求如表二)"
" 2-6各种材料检测记录需备查"
"3.品质要求:"
" 3-1鞋面,鞋底,型号须符合一致,成品构造须符合样品规定."
" 3-2成品大底总成沿条不得脱落及脱底之现象(适用於登山底)."
" 3-3鞋面之缝制须良好,线路整齐,无歪斜,跳针,漏缝,脱线,浮线及断线等不良现象,针码每公分"
" 4-5针及各部线头长度不得超过0.5公分."
" 3-4鞋面面皮须光亮均匀无破损,刀伤,烫伤,碰伤及不得有筋疤,麻点,烙印,不平整等不良现象."
" 3-5鞋舌内里盖印型号及批号不得模糊不清,无法辨认."
" 3-6鞋内不得留有U型钉等异物."
" 3-7鞋面上梆(含后踵部份)须端正圆顺不得歪斜(±0.5公分以内)及凹凸,齿角等钳帮不良现象."
" 3-8左右鞋高度相差应在0.5公分以内."
" 3-9鞋面及鞋底间贴合不可有脱胶,开口之现象."
" 3-10抹胶部份应均匀,且刷胶高度不得超过0.3公分."
" 3-11成品部位(含内里)不得有沾胶,发霉,污染不洁等情形."
" 3-12鞋内里皮,中底须平整,缝牢."
" 3-13鞋垫须贴正,贴牢,不得有歪斜,脱落之现象."
" 3-14每双成品单只装入透明塑胶袋内,另一只亦放透明塑胶袋内,以避免磨擦,每个塑胶袋内装入(1"
" 公克)乾燥剂."
" 3-15成品鞋面双边拉鍊需平顺且不得损坏."
" 3-16鞋面各部位需平整,无皱摺,龟裂等现象."
"4.批之组成:"
" 本规格所称之批量系指在同生产工厂,同一规格,同一时期,同一制程下之产量.(最大批量35000双)"
"5.检验:"
" 5-1外观及包装检查:"
" 5-1-1抽样:依CNS2779Z4006实施抽样,使用一般检验水准一级,正常单次抽样计画,严重疵病(其"
" 中乙项疵病即全批判定不合格),主要疵病AQL6.5%,次要疵病AQL10%,详如下表"
" 严重疵病",,"1.成品构造与样品不符",,,,,,"目视检查"
,,"2.大底总成沿条脱落,脱底(适用於登山底)",,,,,,"目视检查"
,,"3.鞋面破损,刀伤,烫伤等不良现象",,,,,,"目视检查"
,,"4.鞋内钉子未拔除",,,,,,"手触及目视检查"
,,"5.拉鍊损坏",,,,,,"目视检查"
" 主要疵病",,"1.鞋面面皮不光亮均匀",,,,,,"目视检查"
,,"2.鞋面及鞋底间贴合有脱胶,开口之现象",,,,,,"手触及目视检查"
,,"3.中底未平整,鼓起现象",,,,,,"目视检查"
,,"4.鞋里皮未紧贴面皮,浮起现象",,,,,,"目视检查"
,,"5.鞋面各部位不平整(起角),有皱摺,龟裂等现象",,,,,,"目视检查"
"次要疵病A级",,"1.鞋面脏污,沾胶,发霉",,,,,,"目视检查"
,,"2.缝线针码不对,线路歪斜,跳针,漏缝,脱线,浮线及断线",,,,,,"目视检查"
,,"3.鞋面有筋疤,麻点,烙印,等不良现象",,,,,,"目视检查"
,,"4.包装与标志及批号不符",,,,,,"目视检查"
,,"5.鞋舌内里未盖印型号及批号",,,,,,"目视检查"
,,"6.左右鞋高度相差超过0.5公分",,,,,,"量尺量测"
,,"7.鞋面上梆歪斜±0.5公分",,,,,,"目视检查"
" 次要疵病B级",,"1.未置入乾燥剂及装於透明塑胶袋内",,,,,,"目视检查"
,,"2.刷胶高度超过0.3公分",,,,,,"卡尺量测"
,,"3.缝线处未烧断",,,,,,"目视检查"
,,"4.鞋垫未贴正,贴牢,歪斜,脱落现象",,,,,,"目视检查"
,,"5.线头过长超过0.5公分",,,,,,"卡尺量测"
,,"6.批号模糊不清",,,,,,"目视检查"
" 5-1-2检验扣点标准:"
" 5-1-2-1一个主要疵病扣一点,二个次要疵病A级扣一点,三个次要疵病B级扣一点,同一双成品鞋最"
" 多扣一点."
" 5-1-2-2同一双成品鞋有一个(含)以上主要疵病,折算扣一点,或有二个(含)以上次要疵病A级或"
" 有三个次要疵病B级,折算扣一点."
" 5-1-2-3若在不同成品鞋上,其所有疵病数累加计算."
" 5-2尺寸检验:"
" 5-2-1抽样:每型号至少抽取乙双,每批抽取数不得少於八双,其中乙双尺寸不符即全批判定不合格."
" 5-3物性检验:"
" 5-3-1抽样:依CNS2779Z4006实施抽样,使用特殊检验水准S-1级,正常单次抽样计划,AQL4.0%抽样计"
" 划表."
" 5-3-2检验方法:"
" 5-3-2-1橡胶大底及三合一组合底:"
" 5-3-2-1-1硬度:依CNS 3555 K 6346法萧氏A型硬度计检验."
" 5-3-2-1-2抗拉强度:依CNS 3553 K 6344法以3号试验片检验."
" 5-3-2-1-3伸长率:依CNS 3553 K 6344法以3号试验片检验."
" 5-3-2-1-4耐磨性:依CNS 734 K 6047法,荷重2磅,角度15°检验."
" 5-3-2-2成品剥离力:裁取鞋底试样,仅留鞋底及面皮粘合部分为1.5～2.5公分之宽度,将面皮与鞋底"
" 分开5公分长,分别夹於拉力试验机上,以每分钟200㎜±2㎜之拉速拉之,求取平"
" 均值."
" 5-3-2-3成品弯折试验:取试样二双,后跟及前掌部份分别固定於鞋子弯折试验机上,调整机器前掌板"
" 动角度40～50度,速度为每分钟90～100次,注意PVC沿条与胶底间是否有"
" 脱开或任何龟裂现象."
" 5-4但书:1.本项产品(半成品)於进料时检测,成品鉴测时5-3-2-1-1硬度,5-3-2-1-2伸长率,"
" 5-3-2-1-3抗拉强度,5-3-2-1-4耐磨性等四项检验不再实施,惟需提供合格之进料检验纪"
" 录备查."
" 2.半成品之获得方式属於采购行为者,则应於产品鉴测时提供符合「军事机关财物劳务采购"
" 作业规定」合格进料检验纪录备查."
"6.包装与标志:"
" 6-1包装:每箱装12双,箱内每双用小纸盒包装,并注明型号."
" 6-2标志:每个纸箱外面须注明品名,颜色,提制文号,型号,数量,单位,包装重量,出厂日期,制"
" 补单位."
" 6-3批号:每只鞋鞋舌内面及每个纸箱外右上方须盖印批号."
"7.参考资料:"
" CNS2779Z4006 CMS-C-02044 CMS-C-02021 CMS-C-01770"
" CMS-C01252 CMS-C-01144 CMS-C-00708 CNS3555K6346"
" CNS3553K6344 CNS734K6047"
"8.附图(表):"
"表一,尺码表"
,"备 注","一,单位:㎜,公差±1.5㎜"
,,"二, 尺寸依CNS4799S1092检验,以楦头量测",,,,," "," A"
,,"AB:楦头底面长度 "
,,,,,,,," B"
"表二,物性要求表"
,"橡胶登山底","硬度",,,,,"70±5"
,,"伸长率",,,,,"250%(含)以上"
,,"抗拉强度",,,,,"120公斤/平方公分(含)以上"
,,"耐磨性",,,,,"0.4立方公分/2000转(含)以下"
,,"成品剥离力",,,,,"7公斤(含)以上"
,,"成品弯折试验",,,,,"试验鞋面与沿条及大底间10万次(含)以上无剥离现象"
,"三合一组合底","硬度",,,,,"70±5"
,,"伸长率",,,,,"250%(含)以上"
,,"抗拉强度",,,,,"120公斤/平方公分(含)以上"
,,"耐磨性",,,,,"0.4立方公分/2000转(含)以下"
,,"成品剥离力",,,,,"7公斤(含)以上"
,,"成品弯折试验",,,,,"试验鞋面与沿条及大底间10万次(含)以上无剥离现象"
"图一,成品图示:"
""
"共5页第5页 "
"共5页第5页 "
"第16组钢包头安全鞋"
"第16组;第页;共页"
"第16组钢包头安全鞋采购规范"
"第1项:钢包头安全鞋",,,,,"第2项:钢包头安全鞋(H级)"
"第3项:钢包头安全防滑鞋",,,,,"第4项:钢包头安全防滑鞋(H级)"
"编号:MP-304-026G"
"1.适用范围:本规格适用於钢包头安全鞋及钢包头安全运动鞋检验用."
"2.使用材料:"
" 2-1面皮(CMS-C-2044b)"
" 2-2人造中底(加纱布)(CMS-C-1144c)"
" 2-3皮革制安全鞋(CNS6863Z2029)"
" 2-4 PU鞋底或橡胶鞋底(物性如表一)"
" 2-5各项材料检测纪录需备查"
"3.品质要求:"
" 3-1鞋面,鞋垫,型号须符合一致,成品构造须符合样品规定."
" 3-2鞋面之缝制须良好,线路整齐,无歪斜,跳针等现象,针码每公分3-4针,各部线头长度不得超过"
" 0.3公分(含)."
" 3-3鞋面面皮须光亮均匀,无破损,刀伤及皱摺等不良现象."
" 3-4鞋内不得留有U型钉,线头等异物."
" 3-5鞋面与鞋底贴合须端正,不得歪斜,且刷胶高度不可超过0.5公分."
" 3-6鞋底车外线每5公分4-5针(PU鞋底免验)."
" 3-7成品不得有发霉,污染不洁等情形."
" 3-8每双成品须内置一双鞋垫须贴牢,不得有不平整,歪斜等现象"
" 3-9左右鞋高度相差应该在1公分(含)以内."
" 3-10每双成品须以一双鞋带连接系好,以包装纸或塑胶袋相对包装於纸盒内,不得碰撞,刮伤."
" 3-11成品内须置入1公克乾燥剂."
" 3-12鞋面上帮须端正不得左右歪斜0.5公分(含)."
" 3-13鞋底贴合需牢固,不得有开缝脱胶."
" 3-14鞋眼须扎实紧密,无脱落,变形,松动不牢或缺件."
" 3-15鞋内里不可起皱打摺及贴合不良之现象."
" 3-16钢包头内面接合之材料,应贴合平顺,牢固,不可有包空,脱落之现象."
" 3-17护趾钢包头需平正置入,不得歪斜,松动."
"4.批之组成:"
" 本规格所谓之批量系指在同生产工厂,在同一规格,同一时期,同一制程下之产品.(最大批量为"
" 50000双) "
"5.检验:"
" 5-1外观及包装检查:"
" 5-1-1抽样:依CNS2779Z4006实施抽样,使用一般检验水准一级,正常单次抽样计画,严重疵病其中"
" 乙项疵病即全批判定不合格,主要疵病AQL6.5%,次要疵病AQL10%详如下表"
,"严重疵病","1.成品构造与样品不符",,,,,,"目视检查"
,,"2.鞋面破损,刀伤",,,,,,"目视检查"
,,"3.护趾钢包头需平正置入,不得歪斜,松动",,,,,,"目视检查"
,,"4.鞋内留有U型钉",,,,,,"目视检查"
,"主要疵病","1.鞋面上帮不得左右歪斜0.5公分(含)",,,,,,"量尺检查"
,,"2.鞋底贴合开缝脱胶超过5公分(含)以上",,,,,,"量尺检查"
,,"3.成品发霉",,,,,,"目视检查"
,,"4.钢包头内面所接合之材料,未贴合平顺,有皱摺,包空之现象",,,,,,"目视检查"
,,"5.鞋眼未扎实紧密,有脱落,歪斜,变形,松动不牢及缺件",,,,,,"目视检查"
,"次要疵病A级","1.包装与标志不符",,,,,,"目视检查"
,,"2.缝线针码不对,歪斜,跳针,浮线,漏线,脱线,针码每公分3-4针",,,,,,"目视及量尺检查"
,,"3.鞋底车外线每5公分4-5针",,,,,,"量尺检查"
,,"4.鞋面与鞋底贴合不正",,,,,,"目视检查"
,,"5.刷胶高度超过0.5公分(含)",,,,,,"量尺检查"
,,"6.鞋内里起皱打摺及贴合不良之现象",,,,,,"目视检查"
,,"7.成品粘胶,污染不洁等情形",,,,,,"目视检查"
,,"8.鞋面喷漆亮度不均匀及皱摺现象",,,,,,"目视检查"
,,"9.鞋底贴合开缝脱胶小於5公分",,,,,,"量尺检查"
,"次要疵病B级","1.成品未置入鞋垫及贴牢,不平整,歪斜现象",,,,,,"目视检查"
,,"2.左右鞋高度相差超过1(含)公分",,,,,,"量尺检查"
,,"3.线头过长超过0.3(含)公分",,,,,,"量尺检查"
,,"4.未置入1公克乾燥剂",,,,,,"目视检查"
,,"5.鞋面,鞋垫,型号须符合一致",,,,,,"目视检查"
" 5-1-2检验扣点标准:"
" 5-1-2-1一个主要疵病扣一点,二个次要疵病A级扣一点,三个次要疵病B级扣一点,同一双成品鞋最多"
" 扣一点."
" 5-1-2-2同一双成品鞋有一个(含)以上主要疵病折算扣一点,或有二个(含)以上次要疵病A级或有三个"
" 以上次要疵病B级折算扣一点."
" 5-1-2-3若在不同成品鞋上,其所有疵病数累加计算. "
" 5-2物性检验:"
" 5-2-1抽样:依CNS2779Z4006实施抽样,使用特殊检验水准S-1级,正常单次抽样计画AQL4.0%,物性"
" 要求如表一."
" 5-2-2检验方法:"
" 5-2-2-1成品检验:"
" 5-2-2-1-1成品耐压扁试验:依CNS 6863 Z 2029 第8.1节,压扁荷重1400公斤."
" 5-2-2-1-2成品耐冲击试验:依CNS 6863 Z 2029 第8.2节,重锤质量23公斤,落下高度450㎜."
" 5-2-2-1-3成品剥离性试验:依CNS6863Z2029第8.3节."
" 5-2-2-1-4成品铁钉穿透性试验:依CNS6863Z2029第8.8节(若无加钢片则免验)."
" 5-2-2-1-5鞋底(含后跟)最薄厚度量测试验:依CNS6863Z2029第8.6(1)节."
" 5-2-2-2材料试片检验:"
" 5-2-2-2-1橡胶鞋底检验:"
" 5-2-2-2-1-1硬度:依CNS3555K6346法A型硬度计检验之."
" 5-2-2-2-1-2伸长率:依CNS3553K6344第3号试验片测试之."
" 5-2-2-2-1-3抗拉强度:依CNS3553K6344第3号试验片测试之."
" 5-2-2-2-1-4耐磨性:依CNS734K6047检验之."
" 5-2-2-2-1-5鞋底(含后跟)最薄厚度量测试验:依 CNS 6863Z2029第8.6(1)节."
" 5-2-2-2-2 PU鞋底检验:鞋底材料之物理性能试验按下列各项施行之,但试片须由鞋底之聚胺酯泡棉"
" 层制成;但重叠胶合之合成橡胶试片则用与成品鞋底同一材料或成品取下制成之."
" 5-2-2-2-2-1抗拉试验:依CNS3553K6344第2号试验片测试之."
" 5-2-2-2-2-2撕裂试验:依CNS3559K6350第B型试验片测试之."
" 5-2-2-2-2-3老化试验:依CNS3556K6347第2.1节(温度70℃±1℃,120小时)2号试验片测试之.(参"
" 考CNS12708Z2078第8.8.3节)"
" 5-2-2-2-2-4比重试验:依CNS5341K6458法之规定."
" 5-2-2-2-2-5耐油性试验:依CNS3562K6353中之试验方法试算出体积变化率,但试验用油为NO.3油,试"
" 验用油温度40±1 C,浸泡时间为22小时.(参考CNS12708Z2078第8.8.5节)"
" 5-3尺寸检验:"
" 5-3-1抽样:各型号依合约批量抽取(如鞋楦抽样表),其中乙双尺寸不符即全批判定不合格:尺寸要"
" 求如表一. "
,,"鞋楦抽样表","批量(双)",,,"抽样数(每型号)"
,,,"1~10000",,,"1双"
,,,"10001~30000",,,"2双"
,,,"30001~50000",,,"3双"
" 5-3-2尺寸要求:如表二."
" 5-4但书:1.本项产品(半成品)於进料时检测,成品鉴测时半成品检验不再实施,惟需提供合格之进"
" 料检验纪录备查."
" 2.半成品之获得方式属於采购行为者依采购权责办理."
"6.包装与标志:"
" 6-1包装:采用一般商业包装,同批量之包装数须一致(零头数另行包装)."
" 6-2标志:每个纸箱外面须注明品名,颜色,型号,批号,数量,单位,包装重量,出厂日期,制补单"
" 位及保固年限(含储存及穿著使用年限):二年,每只鞋鞋舌内面须盖印型号及批号."
"7.参考资料:"
" CNS2779Z4006 计数值检验抽样程序及抽样表"
" CNS6863Z2029 皮革制安全鞋"
" CNS3555K6346 硫化橡胶硬度试验法"
" CNS3553K6344 硫化橡胶拉伸试验法"
" CNS734K6047 橡胶磨耗试验标准"
" CNS3559K6350 硫化橡胶抗撕裂强度试验法"
" CNS3556K6347 硫化橡胶老化试验法"
" CNS5341K6458 硫化橡胶密度之测定法"
" CNS3562K6353 硫化橡胶浸渍试验法"
" CNS4799S1092 橡胶底帆布鞋及全橡胶鞋之标准铸模尺度"
" CNS4801S1094 皮鞋楦头之标准尺度"
" CNS12708Z2078 发泡聚胺酯鞋底安全鞋"
" CMS-C-1144c 人造中底(加纱布)"
"8.附表(图): "
"图一,成品图:钢包头安全鞋"
"图二,成品图:钢包头安全鞋(H)级"
"表一,物性要求表"
,"成品","耐压扁试验",,,"中底和护趾钢头间之空隙必须有15㎜(含)以上."
,,"耐冲击试验",,,"中底和护趾钢头间之空隙必须有15㎜(含)以上."
,,"剥离力试验(鞋底与鞋面间)",,,"30㎏(含)以上."
,,"耐铁钉穿透性",,,"鞋底不得贯穿."
,,"鞋底最薄厚度(鞋底含后跟)",,,"鞋底最薄部,测试厚度须为3.0㎜(含)以上.(H级鞋底最薄部,测试厚度须为3.5㎜(含)以上)"
,"橡胶鞋底","硬度",,,"70±5"
,,"抗拉强度",,,"140公斤¤平方公分(含)以上."
,,"伸长率",,,"300%(含)以上."
,,"耐磨性",,,"0.3立方公分¤ 2000转(含)以下(以磨角15度,荷重2磅)."
,,"鞋底最薄厚度(鞋底含后跟)",,,"鞋底最薄部,测试厚度须为3.0㎜(含)以上.(H级鞋底最薄部,测试厚度须为3.5㎜(含)以上)"
,"PU鞋底","抗 拉 强 度",,,"抗拉强度",,"60公斤¤平方公分(含)以上."
,,,,,"伸长率",,"300%(含)以上."
,,"撕裂试验",,,"25公斤¤公分(含)以上."
,,"老化试验",,,"抗拉强度之变化率±20%以内."
,,"比重试验",,,"0.5(含)以上."
,,"耐油性试验",,,"体积变化率+10%,-0%"
"表二,尺码表"
,"备注","一.单位:㎜,公差±2㎜ "
,,"二.底长依CNS4799S1092法,量测由A点至B点之楦头底面之长度."
,,"三.楦头周径尺度依CNS4801S1094法,量测由B点绕鞋面一周至C点,测定其距离."
,,"四.型号未明订之底长及楦头周径尺寸则依比例大小级放."
,,"(1)底长",,"A"
,," "
,,,,"B"
,,"(2)楦头周径"
·上一篇：运动与健康"契约条款附件一"
"第1组;第1页;共1页"
"第1组:国产男皮鞋采购规范表"
"项目",,,"第1项","第2项","第3项","第4项","检验方法"
"规格"
1,"鞋面","材质:牛皮","ˇ","ˇ","ˇ","ˇ","放大镜分析"
2,,"厚度:1.2 ~ 1.6mm","ˇ","ˇ","ˇ","ˇ","CNS 1274"
3,,"抗拉强度:120 kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1278"
4,,"撕裂强度:3.0 kgf/mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1279"
5,,"破裂强度:25 kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1353"
6,,"延伸率:30%(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1281"
7,"内里","材质:牛皮(可搭配纺织透气材料)","ˇ","ˇ","ˇ","ˇ","放大镜分析"
8,,"厚度:0.8 mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1274"
9,"中底","材质:三合一定型纸浆+铁心或不织布中底","ˇ","ˇ","ˇ","ˇ","放大镜分析"
10,"鞋垫","牛皮衬里+吸震发泡材料","ˇ",,"ˇ",,"放大镜分析"
,,"纺织衬里+吸震发泡材料",,"ˇ",,"ˇ","放大镜分析"
11,,"抗菌:接触面无细菌滋生","ˇ","ˇ","ˇ","ˇ","AATCC147:98金色葡萄球菌ATCC6538P"
12,"鞋底","材质:","橡胶或复合底","橡胶或复合底","皮革底","皮革底","放大镜分析"
13,,"厚度: mm(含)以上",2.5,2.5,3.5,3.5,"橡胶底:CNS 4869;皮革底:CNS 1274"
14,,"抗拉强度:__kgf/cm2(含)以上",100,100,60,60,"CNS3553,2型试片(橡胶),CNS 1278(皮革)"
15,,"撕裂强度:__kgf/cm(含)以上",30,30,"-","-","CNS3559,B型试片"
16,,"延伸率: %(含)以上",300,300,"-","-","CNS3553,2型试片"
17,,"耐磨:损失量____mm3(含)以下",150,150,"-","-","DIN 53516"
18,,"止滑系数:乾式0.5(含)以上","ˇ","ˇ","ˇ","ˇ","ASTM-F1677"
,,"止滑系数:湿式0.3(含)以上","ˇ","ˇ","ˇ","ˇ"
19,"鞋跟","耐磨:损失量150mm3(含)以下","ˇ","ˇ","ˇ","ˇ","DIN 53516"
20,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
21,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每10 "
,," 公分需有10针(含)以上."
22,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案"
,," ,文字批号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
23,"验收","1. 规范表第20,21,22项由适用机关以目视检查办理. "
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制造厂"
,," 之检验报告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验合格其费"
,," 用由适用机关负担,如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数量在500双"
,," (含)以上,适用机关得选择(1)制造厂检验报告或(2)制造厂送交具公信力第三者检验单位(如经济部标"
,," 准检验局,鞋类暨运动休闲科技研发中心等),得会同立约商代表依CNS2779 Z4006(计数值检验程序"
,," 及抽样表)(采用S-1特殊检验水准,以双为单位,允收水准AQL为4%),办理抽样及检验,检验费"
,," 用由立约商负担."
"第2组国产女皮鞋"
" "
"第2组;第页;共2页"
"第2组:国产女皮鞋采购规范表"
"项目",,,"第1项","第2项","第3项","第4项","检验方法"
"规格"
1,"鞋面","材质:牛皮","ˇ","ˇ","ˇ","ˇ","放大镜分析"
2,,"厚度:1.2 ~ 1.4 mm","ˇ","ˇ","ˇ","ˇ","CNS 1274"
3,,"抗拉强度:120 kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1278"
4,,"撕裂强度:3.0 kgf/mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1279"
5,,"破裂强度:25 kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1353"
6,,"延伸率:30%(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1281"
7,"内里","材质:牛皮(可搭配纺织透气材料)","ˇ","ˇ","ˇ","ˇ","放大镜分析"
8,,"厚度:0.8 mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1274"
9,"中底","材质:三合一定型纸浆+铁心或不织布中底","ˇ","ˇ","ˇ","ˇ","放大镜分析"
10,"鞋垫","牛皮衬里+吸震发泡材料","ˇ",,"ˇ",,"放大镜分析"
,,"纺织衬里+吸震发泡材料",,"ˇ",,"ˇ","放大镜分析"
11,,"抗菌:接触面无细菌滋生","ˇ","ˇ","ˇ","ˇ","AATCC147:98金色葡萄球菌ATCC6538P"
12,"鞋底","材质:","美耐底","美耐底","皮革底","皮革底","放大镜分析"
13,,"厚度: mm(含)以上",3.5,3.5,3,3,"美耐底:CNS 4869;皮革底:CNS 1274"
14,,"抗拉强度:60kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","CNS3553,2型试片(橡胶),CNS 1278(皮革)"
15,,"撕裂强度:__kgf/cm(含)以上",20,20,"-","-","CNS3559,B型试片"
16,,"延伸率: %(含)以上",150,150,"-","-","CNS3553,2型试片"
17,,"耐磨:损失量 400 mm3(含)以下","ˇ","ˇ","ˇ","ˇ","DIN 53516"
18,,"止滑系数:乾式 0.5(含)以上","ˇ","ˇ","ˇ","ˇ","ASTM-F1677"
,,"止滑系数:湿式 0.3(含)以上","ˇ","ˇ","ˇ","ˇ"
19,"鞋跟","耐磨:损失量 250 mm3(含)以下","ˇ","ˇ","ˇ","ˇ","DIN 53516"
20,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
21,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每10 "
,," 公分需有10针(含)以上."
22,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案"
,," ,文字批号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
23,"验收","1. 规范表第20,21,22项由适用机关以目视检查办理. "
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制造厂"
,," 之检验报告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验合格其费用"
,," 由适用机关负担,如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数量在500双(含)"
,," 以上,适用机关得选择(1)制造厂检验报告或(2)制造厂送交具公信力第三者检验单位(如经济部标准检"
,," 验局,鞋类暨运动休闲科技研发中心等),得会同立约商代表依CNS2779 Z4006(计数值检验程序及抽样"
,," 表)(采用S-1特殊检验水准,以双为单位,允收水准AQL为4%),办理抽样及检验,检验费用由立约"
,," 商负担."
"第3组国产男休闲鞋"
"第3组;第页;共2页"
"第3组:国产男休闲鞋采购规范表"
"项目",,,"第1项","第2项","第3项","第4项","第5项","第6项","第7项","第8项","第9项","第10项","第11项","第12项","检验方法"
"规格"
1,"鞋面","材质:牛皮","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","放大镜分析"
2,,"厚度:1.4 ~ 1.8 mm","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1274"
3,,"抗拉强度:120 kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1278"
4,,"撕裂强度:3.0 kgf/mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1279"
5,,"破裂强度:25 kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1353"
6,,"延伸率:30 %(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1281"
7,"内里","材质:牛皮(可搭配纺织透气材料)","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","-","-","-","-","-","-","放大镜分析"
,,"材质:猪皮(可搭配纺织透气材料)","-","-","-","-","-","-","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","放大镜分析"
8,,"厚度:0.8 mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1274"
9,"鞋垫","牛皮衬里+吸震发泡材料","ˇ","ˇ","ˇ","-","-","-","-","-","-","-","-","-","放大镜分析"
,,"猪皮衬里+吸震发泡材料","-","-","-","-","-","-","ˇ","ˇ","ˇ","-","-","-","放大镜分析"
,,"纺织衬里+吸震发泡材料","-","-","-","ˇ","ˇ","ˇ","-","-","-","ˇ","ˇ","ˇ","放大镜分析"
10,,"抗菌:接触面无细菌滋生","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","AATCC147:98金色葡萄球菌ATCC6538P"
11,"鞋底","材质:","橡胶或复合底","PU底","TPR底","橡胶或复合底","PU底","TPR底","橡胶或复合底","PU底","TPR底","橡胶或复合底","PU底","TPR底","放大镜分析"
12,,"厚度:2.5 mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 4869(橡胶,PU,TPR)"
13,,"抗拉强度:__kgf/cm2(含)以上",100,60,50,100,60,50,100,60,50,100,60,50,"CNS3553,2型试片(橡胶,PU,TPR)"
14,,"撕裂强度:__kgf/cm(含)以上",30,25,20,30,25,20,30,25,20,30,25,20,"CNS3559,B型试片"
15,,"延伸率: %(含)以上",300,250,250,300,250,250,300,250,250,300,250,250,"CNS3553,2型试片"
16,,"耐磨:损失量____mm3(含)以下",150,250,280,150,250,280,150,250,280,150,250,280,"DIN 53516"
17,"鞋底","止滑系数:乾式 0.5 (含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ASTM-F1677"
,,"止滑系数:湿式 0.3 (含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ"
18,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
19,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋5针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每10公分需有10 "
,," 针(含)以上. "
20,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案,文字批"
,," 号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
21,"验收","1. 规范表第18,19,20项由适用机关以目视检查办理. "
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制造厂之检验报"
,," 告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验合格其费用由适用机关负担如"
,," 不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数量在500双(含)以上,适用机关得选择(1)制"
,," 造厂检验报告或(2)制造厂送交具公信力第三者检验单位(如经济部标准检验局,鞋类暨运动休闲科技研发中心等"
,," ),得会同立约商代表依CNS2779 Z4006(计数值检验程序及抽样表)(采用S-1特殊检验水准,以双为单位,允"
,," 收水准AQL为4%),办理抽样及检验,检验费用由立约商负担."
"第4组国产女休闲鞋"
"第4组;第页;共2页"
"第4组:国产女休闲鞋采购规范表"
"项目",,,"第1项","第2项","第3项","第4项","第5项","第6项","第7项","第8项","第9项","第10项","第11项","第12项","检验方法"
"规格"
1,"鞋面","材质:牛皮","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","放大镜分析"
2,,"厚度:1.4 ~ 1.8 mm","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1274"
3,,"抗拉强度:120 kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1278"
4,,"撕裂强度:3.0 kgf/mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1279"
5,,"破裂强度:25 kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1353"
6,,"延伸率:30%(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1281"
7,"内里","材质:牛皮(可搭配纺织透气材料)","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","-","-","-","-","-","-","放大镜分析"
,,"材质:猪皮(可搭配纺织透气材料)","-","-","-","-","-","-","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","放大镜分析"
8,,"厚度:0.8 mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 1274"
9,"鞋垫","牛皮衬里+吸震发泡材料","ˇ","ˇ","ˇ","-","-","-","-","-","-","-","-","-","放大镜分析"
,,"猪皮衬里+吸震发泡材料","-","-","-","-","-","-","ˇ","ˇ","ˇ","-","-","-","放大镜分析"
,,"纺织衬里+吸震发泡材料","-","-","-","ˇ","ˇ","ˇ","-","-","-","ˇ","ˇ","ˇ","放大镜分析"
10,,"抗菌:接触面无细菌滋生","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","AATCC147:98金色葡萄球菌ATCC6538P"
11,"鞋底","材质:","橡胶或复合底","PU底","TPR底","橡胶或复合底","PU底","TPR底","橡胶或复合底","PU底","TPR底","橡胶或复合底","PU底","TPR底","放大镜分析"
12,,"厚度:2.5 mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 4869(橡胶,PU,TPR)"
13,,"抗拉强度:__kgf/cm2(含)以上",100,60,50,100,60,50,100,60,50,100,60,50,"CNS3553,2型试片(橡胶,PU,TPR)"
14,"鞋底","撕裂强度:__kgf/cm(含)以上",30,25,20,30,25,20,30,25,20,30,25,20,"CNS3559,B型试片"
15,,"延伸率: %(含)以上",300,250,250,300,250,250,300,250,250,300,250,250,"CNS3553,2型试片"
16,,"耐磨:损失量____mm3(含)以下",150,250,280,150,250,280,150,250,280,150,250,280,"DIN 53516"
17,,"止滑系数:乾式0.5 (含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ASTM-F1677"
,,"止滑系数:湿式0.3 (含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ"
18,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
19,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每10公分需有10 "
,," 针(含)以上. "
20,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案,文字批"
,," 号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
21,"验收","1. 规范表第18,19,20项由适用机关以目视检查办理. "
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制造厂之检验报"
,," 告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验合格其费用由适用机关负担,"
,," 如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数量在500双(含)以上,适用机关得选择(1)"
,," 制造厂检验报告或(2)制造厂送交具公信力第三者检验单位(如经济部标准检验局,鞋类暨运动休闲科技研发中心"
,," 等),得会同立约商代表依CNS2779 Z4006(计数值检验程序及抽样表)(采用S-1特殊检验水准,以双为单位,"
,," 允收水准AQL为4%),办理抽样及检验,检验费用由立约商负担."
"第5组国产运动鞋"
"第5组;第页;共2页"
"第5组:国产运动鞋采购规范表"
"项目",,,"第1项","第2项","检验方法"
"规格"
1,"鞋面","材质:PU+透气网布","ˇ","ˇ","放大镜分析"
2,,"破裂强度:成品鞋常温60度弯曲60,000次(含)以上,鞋面无破损","ˇ","ˇ","SATRA TM92"
3,"里衬","材质:纺织布","ˇ","ˇ","放大镜分析"
4,,"秀气度:15 sec/100 ml(含)以下","ˇ","ˇ","CNS 1357"
5,"中底","材质:纸浆或不织布","ˇ","ˇ","放大镜分析"
6,,"吸水脱附:水份吸收≥70 mg/cm2;水份脱离≥80%的水份吸收","ˇ","ˇ","EN ISO 20344 7.2"
7,"鞋垫","材质:纺织布+吸震发泡材料","ˇ","ˇ","放大镜分析"
8,,"厚度:3 ~ 5 mm","ˇ","ˇ","CNS 1274"
9,,"防霉:1级(滋生面积≤10%)","ˇ","ˇ","ASTM-G21:96白癣菌ATCC9533"
10,,"抗菌:接触面无细菌滋生","ˇ","ˇ","AATCC147:98金色葡萄球菌ATCC6538P"
11,,"透气度:30 sec/100ml(含)以下","ˇ","ˇ","CNS 1357"
12,"中插","材质:","EVA","-","材质分析"
13,,"抗拉强度:____kgf/cm2(含)以上",18,"-","CNS3553,2型试片"
14,,"延伸率:: %(含)以上",200,"-","CNS3553,2型试片"
15,,"撕裂强度:____kgf/cm(含)以上",10,"-","CNS3559,B型试片"
16,,"硬度:HS","52~58","-","CNS Type:E型"
17,,"压缩变形: %(含)以下",55,"-","CNS3560,50.C,6hr"
18,"鞋底","材质: ","橡胶或复合底","TPR","放大镜分析"
19,,"厚度: mm(含)以上",2.5,2.5,"CNS 4869(橡胶,TPR)"
20,,"延伸率:: %(含)以上",360,200,"CNS 734"
21,,"抗拉强度:____kgf/cm2(含)以上",100,50,"CNS3553,2型试片(橡胶,TPR)"
22,,"鞋底与鞋面胶著强度:__kg(含)以上",20,15,"CNS 742"
23,,"吸震性: g(含)以下",12,15,"SATRA TM 142"
24,,"耐磨:2磅2,000转__CC(含)以下",0.3,0.5,"CNS 734"
25,,"止滑系数:乾式____(含)以上",0.5,0.35,"ASTM-F1677"
,,"止滑系数:湿式____(含)以上",0.3,0.25
26,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
27,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每10公分"
,," 需有10针(含)以上. "
28,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案,文"
,," 字批号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
29,"验收","1. 规范表第26,27,28项由适用机关以目视检查办理. "
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制造厂"
,," 之检验报告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验合格其费用"
,," 由适用机关负担,如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数量在500双(含)"
,," 以上,适用机关得选择(1)制造厂检验报告或(2)制造厂送交具公信力第三者检验单位(如经济部标准检"
,," 验局,鞋类暨运动休闲科技研发中心等),得会同立约商代表依CNS2779 Z4006(计数值检验程序及抽样"
,," 表)(采用S-1特殊检验水准,以双为单位,允收水准AQL为4%),办理抽样及检验,检验费用由立约"
,," 商负担."
"第6组皮革制安全鞋"
"第6组;第页;共2页"
"第6组:国产皮革制安全鞋(CNS 6863)采购规范表"
"*作业性质分类:H类为重作业用;S类为普通作业用;L类为轻作业用"
"项目",,,"第1项","第2项","第3项","第4项","第5项","第6项","检验方法"
"规格"
1,"性质","作业性质分类","(H)","(S)","(L)","(H)","(S)","(L)","-"
2,"鞋面","材质:皮革__(含)以上",1.5,1.5,1.2,1.5,1.5,1.2,"CNS 6863 5.2"
3,,"面皮龟裂:高度6mm(含)以上,载重15kgf(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 7.1"
4,,"含铬量:V式及I式3.0～5.5%以内","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 7.1"
5,"钢头","圆顶后端中央点至先端距离____mm","40~60","40~60","30~60","40~60","40~60","30~60","CNS 6863 5.2.3"
6,,"高度:____mm(含)以上",33,33,28,33,33,28,"CNS 6863 5.2.3"
7,,"摺边尺寸:3mm(含)以上,如为斜角者1mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 5.2.3"
8,,"耐压扁 :空隙22mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 7.2"
9,,"耐蚀性:不得有腐蚀痕迹","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 7.2"
10,"鞋底","材质分析:合成橡胶大底","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 7.3"
11,,"止滑性:具止滑作用","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 2.1"
,,"最薄处厚度:____mm(含)以上",3.5,3,2.5,3.5,3,2.5,"CNS 6863 5.2.4"
12,,"抗拉强度:____kgf/cm2(含)以上",140,140,100,140,140,100,"CNS 6863 7.3.(CNS3553,#2号试片)"
13,,"伸长率:____%(含)以上",300,300,200,300,300,200,"CNS 6863 7.3(CNS3553,#2号试片)"
14,,"撕裂强度:____kgf/cm(含)以上",35,35,30,35,35,30,"CNS 6863 7.3(CNS3559,#B号试片)"
15,,"硬度Hs(含)以上",60,60,50,60,60,50,"CNS 6863 7.3(CNS3553,Type-A)"
16,,"耐油性","+10%~-0%","+10%~-0%","+30%~-0%","+10%~-0%","+10%~-0%","+30%~-0%","CNS 6863 7.3.(CNS3562,40±1℃*22H)"
17,,"老化后鞋底弯折:不得折断","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 7.3(70±1℃*120H)"
18,,"老化5天后抗拉强度降低率____%(含)以下",15,15,"-",15,15,"-","CNS 68637.3 (CNS3556,70±1℃*120H) "
19,"鞋底用缝线","抗拉强度:钩缝,内缝线28kgf/根以上,露缝线19 kgf/根以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 7.5"
20,"成品鞋","耐压扁:空隙15mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 4.1"
21,,"耐冲击:空隙15mm(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","CNS 6863 4.1"
22,,"胶著力:____kgf(含)以上",30,30,25,30,30,25,"CNS 6863 4.2(鞋底与鞋面)"
23,,"耐穿刺:静荷重50 kgf是否贯穿鞋底","ˇ","ˇ","-","ˇ","ˇ","-","CNS 6863 4.3(可依据需求增加)"
24,,"抗静电试验:符合CNS 8878要求","ˇ","ˇ","ˇ","-","-","-","CNS 8878(可依据需求增加)"
25,,"耐电压:不得有任何异样且泄漏电流最大不得超过16mA","-","-","-","ˇ","ˇ","ˇ","60Hz交流电压15,000伏特连续1分钟(可依据需求增加)"
26,,"破坏电压:未贯穿","-","-","-","ˇ","ˇ","ˇ","60Hz交流电压20,000伏特连续1分钟(可依据需求增加)"
27,,"止滑性试验:乾式0.5(含)以上;湿式0.3(含)以上","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","ASTM-F1677(可依据需求增加)"
28,,"耐磨耗:150mm3(含)以下","ˇ","ˇ","ˇ","ˇ","ˇ","ˇ","DIN53516(可依据需求增减)"
29,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
30,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每10公分"
,," 需有10针(含)以上. "
31,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案,文"
,," 字批号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
,,"3. 贴有经济部标准检验局授权之合格认证标签;或通过ISO9000国际品质认证或是通过经济部标准检验局"
,," 安全鞋产品登录认证."
32,"验收","1. 规范表第29,30,31项由适用机关以目视检查办理."
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制造厂"
,," 之检验报告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验合格其费用"
,," 由适用机关负担,如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数量在500双 (含"
,," )以上,适用机关得选择(1)制造厂检验报告或(2)制造厂送交具公信力第三者检验单位(如经济部标准检"
,," 验局,鞋类暨运动休闲科技研发中心等),得会同立约商代表依CNS2779 Z4006(计数值检验程序及抽样"
,," 表)(采用S-1特殊检验水准,以双为单位,允收水准AQL为4%),办理抽样及检验,检验费用由立约"
,," 商负担."
"第7组PU鞋底安全鞋"
"第7组;第页;共2页"
"第7组:PU鞋底安全鞋(CNS 12708)采购规范表"
"※作业性质分类:PU-S为普通作业用;PU-L为轻工作用"
"项目",,,"第1项","第2项","第3项","第4项","检验方法"
"规格"
1,"性质","作业性质分类","(PU-S)","(PU-L)","(PU-S)","(PU-L)","-"
2,"鞋面","材质:皮革__(含)以上",1.5,1.2,1.5,1.2,"CNS 6863 5.2"
3,,"面皮龟裂:高度6.0mm(含)以上,载重15.0kgf(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 8.4"
4,,"含铬量:V式及I式3.0～5.5%以内","ˇ","ˇ","ˇ","ˇ","CNS 6863 8.4"
5,"钢头","圆顶后端中央点至先端距离____mm","40~60","30~50","40~60","30~50","CNS 6863 5.2.3"
6,,"高度:____mm(含)以上",33,28,33,28,"CNS 6863 5.2.3"
7,,"摺边尺寸:3mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 5.2.3"
8,,"耐压扁 :空隙15mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 8.1"
9,,"耐撞击 :空隙15mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 8.2"
10,,"耐蚀性:不得有腐蚀痕迹","ˇ","ˇ","ˇ","ˇ","CNS 6863 8.5"
11,"鞋底","大底材质分析:PU大底","ˇ","ˇ","ˇ","ˇ","红外线光谱仪"
12,,"抗拉强度:____kgf/cm2(含)以上",60,60,60,60,"CNS 6863 8.6(CNS3553,#2号试片)"
13,,"伸长率:____%(含)以上",300,300,300,300,"CNS 6863 8.6(CNS3553,#2号试片)"
14,,"撕裂强度:____kgf/cm(含)以上",25,25,25,25,"CNS 6863 8.6(CNS3559,#B号试片)"
15,,"老化(抗拉强度变化率)____%","±20%","±20%","±20%","±20%","CNS 6863 8.6(70±1℃*120H)"
16,,"耐油(体积变化率)","+10%~-0%","+10%~-0%","+10%~-0%","+10%~-0%","CNS3562,40±1℃*22H"
17,,"抗剥离性:____ kgf",30,25,30,25,"CNS 6863 8.3"
18,"成品鞋","耐压扁:空隙15mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 4.1"
19,,"耐冲击:空隙15mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 4.1"
20,,"胶著力:____kgf(含)以上",30,25,30,25,"CNS 6863 4.2(鞋底与鞋面)"
21,,"耐穿刺:静荷重50 kgf是否贯穿鞋底","-","-","ˇ","ˇ","CNS 6863 4.3(可依据需求增加)"
22,,"抗静电试验:符合CNS 8878要求","-","-","ˇ","ˇ","CNS 8878(可依据需求增加)"
23,,"止滑性试验:乾式0.5(含)以上;湿式0.3(含)以上","-","-","ˇ","ˇ","ASTM-F1677(可依据需求增加)"
24,,"耐磨耗:250mm3(含)以下","-","-","ˇ","ˇ","DIN53516. (可依据需求增减) "
25,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
26,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每"
,," 10公分需有10针(含)以上. "
27,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图"
,," 案,文字批号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
,,"3. 贴有经济部标准检验局授权之合格认证标签;或通过ISO9000国际品质认证或是通过经济部标准"
,," 检验局安全鞋产品登录认证."
28,"验收","1. 规范表第25,26,27项由适用机关以目视检查办理."
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制"
,," 造厂之检验报告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验"
,," 合格其费用由适用机关负担,如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购"
,," 数量在500双(含)以上,适用机关得选择(1)制造厂检验报告或(2)制造厂送交具公信力第三者检验"
,," 单位(如经济部标准检验局,鞋类暨运动休闲科技研发中心等),得会同立约商代表依"
,," CNS2779 Z4006(计数值检验程序及抽样表)(采用S-1特殊检验水准,以双为单位,允收水准AQL"
,," 为4%),办理抽样及检验,检验费用由立约商负担."
"第8组国产雨鞋"
"第8组;第页;共1页"
"第8组:国产雨鞋采购规范表"
"项目",,,"第1项","第2项","检验方法"
"规格"
1,"鞋面","材质","橡胶","PVC","放大镜分析"
2,,"高度(筒身橡胶部分离地高度)____cm,中,短统雨鞋(男性用)不限高度","30±2cm","30±2cm","CNS 4870(可依需求增减)"
3,,"抗拉强度:____kgf/cm2(含)以上",30,30,"CNS 3479"
4,,"耐寒试验","无异状","无异状","CNS 3479"
5,,"浸水试验","无异状","无异状","CNS 3479"
6,"鞋垫","材质不限,由厂商自行提供","ˇ","ˇ","-"
7,"鞋底","材质:","橡胶或复合底","PVC","放大镜分析"
8,,"厚度:不著地 cm(含)以上",0.2,0.2,"CNS 4869(橡胶,PVC)"
9,,"抗拉强度:____kgf/cm2(含)以上",30,30,"CNS 3479"
10,,"延伸率: %(含)以上",120,120,"CNS 3479"
11,,"不渗透性","不渗漏,未膨胀,未硬化及未龟裂","不渗漏,未膨胀,未硬化及未龟裂","CSN12707 A-1"
12,,"止滑系数:乾式0.6(含)以上","ˇ","ˇ","ASTM-F1677"
13,,"止滑系数:湿式0.4(含)以上","ˇ","ˇ"
14,"筒身","筒身顶部:须有绳索束紧功能并带lock装置","ˇ","ˇ","放大镜分析"
15,,"厚度:0.1cm(含)以上","ˇ","ˇ","CNS 4870"
16,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
17,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每10 "
,," 公分需有10针(含)以上."
18,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案"
,," ,文字批号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
19,"验收","1. 规范表第16,17,18项由适用机关以目视检查办理. "
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制造"
,," 厂之检验报告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验由适"
,," 用机关负担,如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数量在500双(含)"
,," 以上,适用机关得选择(1)制造厂检验报告或(2)制造厂送交具公信力第三者检验单位(如经济部标准"
,," 检验局,鞋类暨运动休闲科技研发中心等),得会同立约商代表依CNS2779 Z4006(计数值检验程序"
,," 样表)(采用S-1特殊检验水准,以双为单位,允收水准AQL为4%),办理抽样及检验,检验费用"
,," 由立约商负担."
"第9组国产消防救护用工作鞋"
"第9组;第页;共3页"
"第9组:国产消防救护用工作鞋采购规范表"
"项目",,,"第1项","第2项","第3项","第4项","检验方法"
"规格"
1,"鞋面","材质:牛皮","ˇ","ˇ","ˇ","ˇ","放大镜分析"
2,,"厚度:1.6~1.8mm","ˇ","ˇ","ˇ","ˇ","CNS 1274"
3,,"抗拉强度:120kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1278"
4,,"撕裂强度:3kgf/mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1279"
5,,"破裂强度:25kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1353"
6,,"延伸率:30%(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1281"
7,"鞋统","材质:纺织材料+泡棉或针轧棉","ˇ","ˇ","ˇ","ˇ","放大镜分析"
8,,"泡棉或针轧棉厚度:2.5mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1274"
9,"内里","材质:纺织衬里+吸震发泡材料","ˇ","ˇ","ˇ","ˇ","放大镜分析"
10,,"发泡材料厚度:3mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1274"
11,"后包","材质:牛皮","ˇ","ˇ","ˇ","ˇ","放大镜分析"
12,,"厚度:1.6~1.8mm","ˇ","ˇ","ˇ","ˇ","CNS 1274"
13,"鞋舌","材质:纺织材料+泡棉或针轧棉","ˇ","ˇ","ˇ","ˇ","放大镜分析"
14,,"泡棉或针轧棉厚度:2.2mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1274"
15,"滚口","材质:纺织材料+泡棉或针轧棉","ˇ","ˇ","ˇ","ˇ","放大镜分析"
16,,"泡棉或针轧棉厚度:20mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 1274"
17,"鞋眼","古铜色单脚D型环7个(1-2,4-8)及古铜色双脚D型环1个(3)","ˇ","ˇ","ˇ","ˇ","放大镜分析"
18,"鞋垫","材质1:牛皮衬里+吸震发泡材料","ˇ","ˇ","-","-","放大镜分析"
19,,"材质2:纺织衬里+吸震发泡材料","-","-","ˇ","ˇ","放大镜分析"
20,,"抗菌:接触面无细菌滋生","ˇ","ˇ","ˇ","ˇ","AATCC147:98金色葡萄球菌ATCC6538P"
21,"鞋底","材质:橡胶或复合底","ˇ","ˇ","ˇ","ˇ","放大镜分析"
22,,"厚度:3.5mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 4869(橡胶)"
23,,"抗拉强度:140kgf/cm2(含)以上","ˇ","ˇ","ˇ","ˇ","CNS3553,2型试片(橡胶),CNS 1278(皮革)"
24,,"撕裂强度:30kgf/cm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS3559,B型试片"
25,,"延伸率:300%(含)以上","ˇ","ˇ","ˇ","ˇ","CNS3553,2型试片"
26,,"耐油性:+10%~-0%","ˇ","ˇ","ˇ","ˇ","CNS3562,40±1℃*22H"
27,"鞋跟","耐磨:损失量150mm3(含)以下","ˇ","ˇ","ˇ","ˇ","DIN 53516"
28,"成品鞋","耐压扁:空隙15mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 4.1(H级)"
29,,"耐冲击:空隙15mm(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 4.1(H级)"
30,,"胶著力:30kgf(含)以上","ˇ","ˇ","ˇ","ˇ","CNS 6863 4.2(鞋底与鞋面)"
31,,"耐穿刺:静荷重50 kgf是否贯穿鞋底","ˇ","ˇ","ˇ","ˇ","CNS 6863 4.3(可依据需求增加)"
32,,"抗静电试验:符合CNS 8878要求","ˇ","-","ˇ","-","CNS 8878(可依据需求增加)"
33,,"耐电压:不得有任何异样且泄漏电流最大不得超过16mA","-","ˇ","-","ˇ","60Hz交流电压15,000伏特连续1分钟(可依据需求增加)"
34,,"破坏电压:未贯穿","-","ˇ","-","ˇ","60Hz交流电压20,000伏特连续1分钟(可依据需求增加)"
35,"成品鞋","止滑性试验:乾式0.5(含)以上;湿式0.3(含以上)","ˇ","ˇ","ˇ","ˇ","ASTM-F1677(可依据需求增加)"
36,,"耐磨耗:150mm3(含)以下","ˇ","ˇ","ˇ","ˇ","DIN53516. (可依据需求增减) "
37,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
38,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每"
,," 10公分需有10针(含)以上. "
39,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案"
,," ,文字批号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
,,"3. 贴有经济部标准检验局授权之合格认证标签;或通过ISO9000国际品质认证或是通过经济部标准检"
,," 验局安全鞋产品登录认证."
40,"验收","1. 规范表第37,38,39项由适用机关以目视检查办理. "
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制"
,," 造厂之检验报告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验合"
,," 格其费用由适用机关负担,如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数"
,," 量在500双(含)以上,适用机关得选择(1)制造厂检验报告或(2)制造厂送交具公信力第三者检验单"
,," 位(如经济部标准检验局,鞋类暨运动休闲科技研发中心等),得会同立约商代表依"
,," CNS2779 Z4006(计数值检验程序及抽样表)(采用S-1特殊检验水准,以双为单位,允收水准AQL为"
,," 4%),办理抽样及检验,检验费用由立约商负担."
"第10组海巡勤务工作鞋"
"第10组;第页;共页"
"第10组:海巡勤务工作鞋采购规范表"
"项目",,,"第1项","第2项","第3项","检验方法"
"规格"
1,"鞋面","材质:","牛皮","珠面牛皮(防泼水处理)","光面黄牛珠面皮","材质分析"
2,,"厚度:1.5mm(含)以上","ˇ","ˇ","ˇ","CNS 1274"
3,,"抗拉强度:__ kgf/cm2(含)以上",120,120,120,"CNS 1278"
4,,"撕裂强度:__ kgf/mm(含)以上",3,3,3,"CNS 1279"
5,,"破裂强度:__ kgf/cm2(含)以上",25,25,35,"CNS 1353"
6,"内里","材质:","(1)透气细布 (2)防水透气膜 (3)透气泡绵 (4)纺织品","0.8mm以上牛皮","0.6~1.0mm牛皮全里","材质分析,厚度CNS1274"
7,"中底","材质:","皮克隆","中底纸浆版","纸浆定型中底,中置铁心","材质分析"
8,"鞋垫","发泡材料+抗菌布料(无细菌滋生)","ˇ","ˇ","ˇ","材质分析 抗菌性能-AATCC 147:1998 金色葡萄球菌 ATCC 6538P"
,,"防霉(1级) 纺织品+吸震垫+EVA边墙脚杯","-","-","ˇ","防霉性试验-白癣菌 ASTM G21-96 ATCC 9533"
9,"鞋底","材质:","耐油橡胶±10%以下,加上EVA,双密度成型,重量超轻,软,耐电压3300伏特","橡胶","耐油橡胶±10%以下+防印记(4级)","放大镜分析 耐油-CNS 6863,IRM#903 23±2℃×22hrs 不留痕迹试验-4级 灰色标比对"
10,"鞋底","抗拉强度:__kgf/cm2(含)以上",120,120,120,"CNS3553,2型试片"
11,,"撕裂强度:__kgf/cm(含)以上",35,35,35,"CNS3559,B型试片"
12,,"延伸率: %(含)以上",350,350,350,"CNS3553,2型试片"
13,,"耐磨:损失量____mm3(含)以下",200,200,200,"DIN 53516"
14,,"止滑系数:乾式__(含)以上",0.8,0.8,"0.8","ASTM-F1677"
,,"止滑系数:湿式__(含)以上",0.5,0.5,0.5
15,"耐挠性","__次不生龟裂",40000,40000,40000,"SATRA TM77 弯曲角度600"
16,"制造方式",,"加州作法C式成型;高温高压成型绝不脱胶","鞋面与鞋底采胶著黏合+大底车缝","固特异(G式)","制造种类判定"
17,"要求事项",,"-","-","1,黑色半高筒款系带式,成品完整并附鞋带2条. 2,鞋面与鞋身车缝部分以30番进口尼龙车缝,车缝针距每10公分约32针(含)以上.","游标卡尺"
18,"外观","1. 鞋面皮需平整无皱折,刮痕,破损,色差,不洁等瑕疵. 2. 全鞋之平稳性需佳,左右脚高度一致不可歪斜不正."
19,"制工","1. 鞋面缝制需良好整齐,无歪斜,跳针,浮线,漏缝等现象,每英吋10针(含)以上."
,,"2. 鞋底与鞋面接合处不得有开口及贴合不良缝隙,机关下订时其样鞋之鞋款需车缝大底线者,则每10公分需有"
,," 10针(含)以上. "
20,"包装标示","1. 每双用小纸盒包装,注明颜色,型号,尺寸等,每箱装12双或依适用机关要求办理."
,,"2. 每个纸箱外面需注明品名,颜色,型号,数量,出厂日期等.如遇适用机关需印制其它标志,图案,文字批"
,," 号,符号或如套量个人之单位,姓名等,立约厂商需无条件配合办理."
,,"3. 删除"
21,"验收","1. 规范表第18,19,20项由适用机关以目视检查办理. "
,,"2. 立约商交货时提出之检验报告:【1】若单一项次或单一鞋款订购数量未达500双,立约商应检附制造厂之检"
,," 验报告,若适用机关对於制造厂检验报告有疑虑,得会同立约商办理抽样及检验,检验合格其费用由适用机"
,," 关负担,如不合格检验费用由立约商负担.【2】若单一项次之单一鞋款订购数量在500双(含)以上,适用机"
,," 关得选择(1)制造厂检验报告或(2)制造厂送交具公信力第三者检验单位(如经济部标准检验局,鞋类暨运动"
,," 休闲科技研发中心等),得会同立约商代表依CNS2779 Z4006(计数值检验程序及抽样表)(采用S-1特殊检验"
,," 水准,以双为单位,允收水准AQL为4%),办理抽样及检验,检验费用由立约商负担."
,," "
"第11组伞兵长统皮鞋"
"第11组;第页;共页"
"第11组伞兵长统皮鞋采购规范"
"第1项:伞兵长统皮鞋-固特异底",,,,,,"第2项:伞兵长统皮鞋-橡胶注射底"
"编号:MPC-S-304-00013F(原编号:MPC-304-033E)"
"1.适用范围:本规格适用於陆军伞兵皮鞋检验用"
"2.适用资料:(本节说明规格制订时所适用之规格标准)"
" 2-1中华民国国家标准"
" CNS2779Z4006 计数值检验抽样程序及抽样表"
" CNS734K6047 橡胶磨耗试验标准"
" CNS3555K6346 硫化或热塑性橡胶硬度试验法"
" CNS3553K6344 硫化橡胶拉伸试验法"
" CNS 3689 Z 7043 第6.4.1节 中国国家标准之程式"
" CNS3556K6347 硫化橡胶老化试验法"
" CNS6863Z2029 皮革制安全鞋."
" CNS4799S1092 橡胶底帆布皮鞋及全橡胶之标准铸模尺度"
" CNS4801S1094 皮鞋楦头之标准尺度"
" 2-2国军军品规格"
" CMS-P-050001 面皮"
" CMS-C-050006 皮鞋里皮"
"3.品质要求:"
" 3-1成品构造须符合军品确样样品规定."
" 3-2鞋面之缝制须良好,线路整齐,无歪斜,跳针,漏缝及断裂等现象,针码每3公分8-12针,各部线"
" 头长度不得超过0.3公分."
" 3-3鞋面面皮须光亮均匀,无破损,刀伤,烫伤,碰伤,筋疤,麻点,脏污,沾胶及发霉等不良现象."
" 3-4鞋内不得留有钉子等异物."
" 3-5鞋面上梆须端正不得左右歪斜0.5公分以上. "
" 3-6双鞋后部高度相差不得超过0.5公分以上. "
" 3-7鞋眼须扎实紧密,无脱落,变形或缺件."
" 3-8鞋内中底须平整无鼓起现象."
" 3-9每双成品以一双鞋带连接系好."
" 3-10每只成品鞋,鞋内须塞入纸团,不得少於三张."
" 3-11每双成品鞋装入小纸盒,须每单脚以塑胶袋包装,并置入1公克乾燥剂一包."
" 3-12成品鞋后踵须平整."
" 3-13鞋底车沿条应扎实紧密,针码每5公分7-9针(固特异贴底)."
" 3-14鞋垫须贴正,贴牢,裁制大小适中,不得有过大皱摺或过小未覆盖中底之现象."
" 3-15鞋底与鞋面粘合需紧密,不得有脱胶开缝,齿角凹凸及鞋面皱摺之现象."
" 3-16每双鞋须吊挂保养使用须知,外盒并标示型号并置入纸撑及隔板."
" 3-17注射鞋底应无显著气泡,杂物等现象,每只鞋底缺胶部分,面积超过0.5X0.5平方公分者不得超过"
" 3处,外底边缘应修剪整齐,鞋底与鞋面接合处胶边余胶部分长度或高度不得超过0.5公分."
" 3-18上胶部份应均匀,且刷胶高度不得超过0.5公分."
"4.批之组成:"
" 本规格所谓之批量系指在同生产工厂,在同一规格,同一时期,同一制程下之产量(最大批量50000"
" 双)."
"5.抽样与检验:"
" 5-1抽样:"
" 5-1-1外观及包装抽样依CNS2779Z4006实施抽样,使用一般检验水准I级,正常单次抽样计画."
" 5-1-2尺寸检验抽样:各型号依合约批量抽取(如鞋楦抽样表),其中1双尺寸不符即全批判定不合"
" 格;尺寸要求如表2."
,,"鞋楦抽样表","批量(双)",,"抽样数(每型号)"
,,,"1~3000",,"1双"
,,,"3001~6000",,"2双"
,,,"6001以上",,"5双"
" 5-1-3物性检验抽样:依CNS2779Z4006实施抽样,使用特殊检验水准S-1级,单次抽样计画,AQL"
" 4.0%抽样计画."
" 5-2检验:"
" 5-2-1外观及包装检验:严重疵病其中1项疵病即全批判定不合格,主要疵病AQL6.5%,次要疵病"
" AQL10%(详如下表)"
"严重疵病","1.型号不符.",,,,,,"目视检查"
,"2.鞋内有U型钉等异物.",,,,,,"目视检查"
,"3.鞋面破损,刀伤不良现象.",,,,,,"目视检查"
"主要疵病","1.后踵不平整.",,,,,,"目视检查"
,"2.鞋面上梆歪斜,齿角凹凸及鞋面皱摺之现象.",,,,,,"目视检查"
,"3.砸眼不牢,歪斜,脱落,缺件.",,,,,,"目视检查"
,"4.鞋垫未贴正,贴牢,裁制大小不适中,有过大皱摺或过小未覆盖中",,,,,,"目视检查"
," 底之现象."
,"5.鞋面与鞋底粘合不良,有脱胶开缝之现象.(宽度或深度超过1公分 ",,,,,,"目视及量尺检查"
," 含以上)"
,"6.鞋面有烫伤,碰伤,麻点,发霉及筋疤等不良现象.",,,,,,"目视检查"
,"7.胶底缺胶,不熟鼓起,表面不平整或成海绵状,脱跟,脱底(橡胶注",,,,,,"目视检查"
," 射成型)."
"次要疵病A级","1.沿条车外线针码每5公分不足7~9针.(固特异贴底)",,,,,,"量尺量测"
,"2.鞋面缝线针码不对,歪斜,跳针,漏缝,断裂等不良现象.",,,,,,"目视检查"
,"3.车沿条针码每5公分7-9针.",,,,,,"量尺量测"
,"4.鞋垫及中底不平整,有鼓起现象.",,,,,,"手触及量尺检查"
,"5.鞋面脏污,沾胶.",,,,,,"目视检查"
,"6.鞋面与鞋底粘合不良,有脱胶开缝之现象.(宽度或深度小於1公分)",,,,,,"目视及量尺检查"
,"7.鞋面烫伤或经整烫后留有明显刷痕,未恢复鞋面之亮度.",,,,,,"目视检查"
,"8.刷胶高度超过0.5公分",,,,,,"卡尺量测"
"次要疵病B级","1.双鞋后部高度相差不得超过0.5公分以上. ",,,,,,"量尺量测"
,"2.各部线头长度不得超过0.3公分. ",,,,,,"量尺量测"
,"3.未系鞋带或未吊挂保养使用须知.",,,,,,"目视检查"
,"4.鞋内未塞入纸团及少於三张薄纸片.",,,,,,"目视检查"
,"5.成品鞋装入小纸盒未以塑胶袋包装.",,,,,,"目视检查"
,"6.塑胶袋内未装入1公克乾燥剂.",,,,,,"目视检查"
" 5-2-1-1检验扣点标准:"
" 5-2-1-1-1 1个主要疵病扣1点,2个次要疵病A级扣1点,3个次要疵病B级扣1点,同1双成品鞋最多"
" 扣1点."
" 5-2-1-1-2 同1双成品鞋有1个以上主要疵病,折算扣1点,或有2个以上次要疵病A级或有3个以上次"
" 要疵病B级,折算扣1点."
" 5-2-1-1-3若在不同成品鞋上,其所有疵病数累加计算."
" 5-2-2尺寸检验:依合约委制各型号数量抽取,其中1双尺寸不符即全批判定不合格:尺寸要求如表"
" 2."
" 5-2-3物性检验:物性检验需符合物性要求表1."
" 5-2-4检验方法(半成品):"
" 5-2-4-1固特异橡胶大底试片及橡胶射出底试片:"
" 5-2-4-1-1硬度:依CNS3555K6346法检验之(A型硬度计量测)."
" 5-2-4-1-2伸长率:依CNS3553K6344第3号试验片测试之."
" 5-2-4-1-3抗拉强度:依CNS3553K6344第3号试验片测试之."
" 5-2-4-1-4耐磨性:依CNS734K6047法,磨角15度,荷重2磅检验之."
" 5-2-4-1-5老化试验(橡胶注射底适用):依CNS3556K6347中「空气加热老化试验」(常态烘箱法"
" )规定,先将试样以70±3℃做连续加速老化120小时后再依前项第(5-2-4-1-3)节同方"
" 法测定其抗拉强度,并计算老化处理前后之变化率."
" 5-2-5成品检验方法:"
" 5-2-5-1固特异贴底成型剥离力试验:依CNS6863Z2029第8.3节检验之."
" 5-2-5-2成品橡胶注射成型剥离力:先将面皮及后跟割开取下,再自鞋尖中心切割至后踵,将鞋切"
" 成两半作成两样条(不可破坏任何胶底与面皮粘合部分);并将中底清理乾净(避免影响测试"
" 之精密度)再任意取其一样条一端,剥离约40㎜长后,剥离两端分别夹於拉力试验机上,以"
" 每分钟200㎜±2㎜之拉速拉之,取记录值较高一端波状各顶点之胶著荷重之平均值即为剥离"
" 力需符合表2之要求."
" 5-2-5-3成品铁钉穿透性试验:依CNS6863Z2029第8.8节方法检验.(以100公斤静载重10秒,检查"
" 铁钉是否贯穿鞋底;若无加钢片则免验)."
" 5-3但书:1.本项产品(半成品)於进料时检测,成品鉴测时5-2-4-1-1硬度,5-2-4-1-2伸长率,"
" 5-2-4-1-3抗拉强度,5-2-4-1-4耐磨性及5-2-4-1-5老化试验不再实施,惟需提供合格之"
" 进料检验纪录备查."
" 2.半成品之获得方式属於采购行为者依采购权责办理."
" 3.本项成品「铁钉穿透性」试验,视委制单位需求办理."
"6.包装与标志:"
" 6-1包装:同批量之包装数须一致(每箱不得超出10双;零头数另行包装),另每双装入小纸盒平放,"
" 小纸盒外标示型号及批号."
" 6-2标志:每个纸箱外面须注明品名,颜色,型号,批号,数量,单位,包装重量,出厂日期,制补"
" 单位及保固年限(含储存及穿著使用年限):2年,每只鞋鞋舌内面须盖印型号及批号."
"7.附表(图)成品图示:(图示仅供参考,依军种确样之样品为主) "
" "
"表1,物性要求表"
"固特异贴底","硬度",,,,"75±5(A型硬度计测量)"
,"伸长率",,,,"310%以上"
,"抗拉强度",,,,"105公斤/平方公分以上"
,"耐磨性",,,,"0.35立方公分/2000转以下(磨角15度,荷重2磅)"
,"成品剥离力(鞋面与大底间)",,,,"20公斤以上(全鞋底剥离)"
"橡胶注射底","硬度",,,,"65±5 (A型硬度计测量)"
,"伸长率",,,,"400%以上"
,"抗拉强度",,,,"140公斤/平方公分以上"
,"耐磨性",,,,"0.35立方公分/2000转以下"
,,,,,"(磨角15度,荷重2磅)"
,"老化试验",,,,"抗拉强度降低率25%以下"
,"成品剥离力(鞋面与大底间)",,,,"5公斤以上(鞋底单边剥离)"
"成品耐铁钉穿透性",,,,,"100㎏鞋底不得贯穿"
"表2,鞋楦尺寸表 "
"备注","1.单位:㎜,公差±2㎜ ",,,,"(1)底长"
,"2.底长依CNS4799S1092法,量测由A点至B点之楦头底面之长度. ",,,,,"A"
,"3.楦头周径尺度依CNS4801S1094法,量测由B点绕鞋面经过C点再回至B点,测定其距离."
,"4.型号未明订之底长尺寸则依比例大小级放. ",,,,,"B"
," ",,,,"(2)楦头周径 "
," "
"共6页第3页"
"第12组女官士皮鞋"
"第12组;第页;共页"
"第12组女官士高跟,平跟皮鞋采购规范"
"第1项:女官士高跟鞋",,,,,,"第2项:女官士平跟鞋"
"编号:MPC-S-203-00073H(原编号:MPC-S-304-00014G)"
"1.适用范围:本规格适用於各款(高,低跟及平底)三军女性军士官及员工皮鞋检验用."
"2.适用资料:(本节说明规格制订时所适用之规格标准)"
" 2-1中华民国国家标准"
" CNS2779Z4006 计数值检验抽样程序及抽样表"
" CNS734K6047 橡胶磨耗试验标准"
" CNS3555K6346 硫化或热塑性橡胶硬度试验法"
" CNS3553K6344 硫化橡胶拉伸试验法"
" CNS3689Z7043 第6.4.1节 中国国家标准之程式"
" CNS4869S1096 鞋用橡胶底"
" CNS742S2009 运动鞋类检验法"
" CNS4801S1094 皮鞋楦头之标准尺度"
" 2-2美国测试与材料学会(ASTM)标准"
" ASTM D1894 止滑性试验法"
" 2-3国军军品规格"
" CMS-P-050025 女用鞋面皮"
" CMS-C-2046a 猪(面)里皮"
" CMS-C-1180b 鞋用人造衬料"
"3.品质要求:"
" 3-1原料要求:"
" 3-1-1鞋面皮:需符合CMS-P-050025各项要求."
" 3-1-2鞋里皮:需符合CMS-C-2046a猪面皮各项要求."
" 3-1-3港宝:需符合CMS-C-1180b 1.3 mm人造衬料各项要求."
" 3-1-4鞋底:需符合3.2.3物性各项要求."
" 3-2成品要求:"
" 3-2-1工艺,外观及包装:符合第4.3.1节所列各项疵病允收值要求."
" 3-2-2尺寸:符合表1之尺寸要求."
"表1:尺寸要求表 橡胶鞋底尺寸要求表 型号 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 长度 233 237 240 243 246 250 253 256 260 263 266 270 273 276 279 PCU鞋底尺寸要求表 型号 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 长度 218 222 226 230 234 238 242 246 250 254 258 262 266 270 274 备注 一.长度以楦头长度量测,量测方法:依CNS4801S1094法执行. 二.单位:公厘,公差为 2公厘. 三.表内未订型号,其尺寸要求按长度级放比例制作. 四.后跟高度(含天皮):(每双成品后跟高度公差为 1/16吋) (一)平底:1吋(不含)以下. (二)低跟:1吋(含)至1.5吋(不含). (三)高跟:1.5吋(含)以上. "
" 3-2-3物性:符合表2之物性要求."
"表2:物性要求表 橡胶鞋底 硬度 70±5(A型硬度计测量) . 伸长率 250%以上. 抗拉强度 120公斤/平方公分以上. 耐磨性 0.40立方公分/2000转以下(磨角15度,荷重2磅). 成鞋胶著力(鞋底与鞋面间) 7公斤以上. 成鞋止滑效果量测 测试厚度须为2.5㎜以上. PCU鞋底 弯曲试验 试验鞋面与大底间5万次不得有开缝之现象. 止滑性试验(静摩擦系数) 乾 式 0.5以上. 湿 式 0.4以上."
"4.品质保证及检验:"
" 4-1品保规定:"
" 4-1-1检验权责:如合约上无其他规定,由规格鉴测中心实施成品抽样检验,检验纪录应保持完整 ,以备有关上级谘询及查验."
" 4-1-2产品品鉴:制供商应提供下列资料:"
" 4-1-2-1产品零件(原料)检验报告单."
" 4-1-2-2军品合格保证单."
" 4-2检验规定:"
" 4-2-1产品之批量:本规格所谓之批量系指在同生产工厂,在同一规格,同一时期,同一制程下之 产量(最大批量10000双). 4-2-2抽样: 4-2-2-1工艺,外观及包装:抽样依CNS2779Z4006实施抽样,使用一般检验水准I级,正常单次抽样 计画. 4-2-2-2尺寸检验抽样:各型号依合约批量抽取(如鞋楦抽样表),其中1双尺寸不符即全批判定不 合格."
,,"鞋楦抽样表","批量(双)",,"抽样数(每型号)"
,,,"1~3000",,"1双"
,,,"3001~6000",,"2双"
,,,"6001以上",,"5双"
" 4-2-2-3物性检验抽样:依CNS2779Z4006实施抽样,使用特殊检验水准S-1级,单次抽样计画 AQL4.0%."
" 4-3检验:"
" 4-3-1工艺,外观及包装检验:依据下表所列之疵病分类及检验方法进行检验,其中严重疵病只要1项即全批判定不合格;而主要疵病AQL6.5%,次要疵病AQL10%,并依表后所列扣点标准计算之."
,"严重疵病","1.型号不符",,,,,"目视检查"
,,"2.鞋内有U型钉等异物",,,,,"目视检查"
,,"3.鞋跟大底应接(贴)合欠牢固,有松动及歪斜之现象.",,,,,"目视检查"
,,"4.鞋面破损,刀伤",,,,,"目视检查"
,,"5.成品构造未符合确样样鞋规定",,,,,"目视检查"
,"主要疵病","1.鞋面与鞋底贴合不正有歪斜现象.",,,,,"目视检查"
,,"2.鞋面与鞋底粘合不良,有脱胶开缝3现象(宽度或深度超过1公分含以上)",,,,,"目视及量尺"
,,"3.鞋面烫伤,碰伤,烙印及麻点",,,,,"目视检查"
,,"4.港宝(热熔胶片)歪斜,变形及结梆后痕迹外显",,,,,"目视检查"
,,"5.鞋面上梆歪斜有凹凸及齿角等不良现象",,,,,"目视检查"
,"次要疵病A级","1.鞋面缝制针码每公分4-6针",,,,,"量尺量测"
,,"2.线头长度超过0.3公分",,,,,"量尺量测"
,,"3.鞋面缝制线路起皱,歪斜,跳针,漏缝",,,,,"目视检查"
,,"4.成品左右鞋高度超过0.3公分",,,,,"量尺量测"
,,"5.成品磨粗高度超出0.3公分以上或未烫平整,或喷漆不均匀",,,,,"目视及量尺检查"
,,"6.鞋面与鞋底粘合不良,有脱胶开缝之现象(宽度或深度小於1公分)",,,,,"目视及量尺检查"
,"次要疵病 B级","1.鞋垫贴合不平整,有过大浮鼓或过小未覆盖中底之现象",,,,,"目视检查"
,,"2.包装与第5-1节规定不符",,,,,"目视检查"
,,"3.标示与第5-2节规定不符",,,,,"目视检查"
,,"4.鞋面有筋疤,皱摺现象",,,,,"目视检查"
,,"5.上胶部分不均或刷胶高度超过0.3公分",,,,,"目视检查"
,,"6.鞋面各部位(含内里)有沾胶,发霉,污染不洁等现象",,,,,"目视检查"
"※疵病检验扣点标准:"
" (1)成品鞋中之1个主要疵病扣1点,2个次要疵病A级扣1点,3个次要疵病B级扣1点,同1双成品鞋最 多扣1点."
" (2)若疵病出现在不同成品鞋上,则其所有疵病数累加计算."
" 4-3-2尺寸检验:依合约委制各型号数量抽取,其中1双尺寸不符即全批判定不合格:尺寸要求如表1."
" 4-3-3物性检验:"
" 4-3-3-1橡胶鞋底试片: 4-3-3-1-1硬度:依CNS3555K6346法检验之(A型硬度计量测). 4-3-3-1-2伸长率:依CNS3553K6344第3号试验片测试之. 4-3-3-1-3抗拉强度:依CNS3553K6344第3号试验片测试之. 4-3-3-1-4耐磨性:依CNS734K6047法,磨角15度,荷重2磅检验之. 4-3-3-1-5成鞋胶著力试验:依CNS 742 S 2009第16.1节检验之. 4-3-3-1-6成鞋止滑效果量测:依CNS4869S1096第4.1节检验之. 4-3-3-2 PCU鞋底: 4-3-3-2-1成鞋弯曲试验:取试样二双,后跟及前掌部份分别固定於鞋子弯曲试验机上,调整机器前 掌板动角度40～50度,速度为每分钟100～105次,注意沿条与鞋底间是否 有脱开或任何龟裂现象. 4-3-3-2-2成鞋止滑性试验(静摩擦系数) :依ASTM D1894法检验之."
"5.包装及标志:"
" 5-1包装:同批量之包装数须一致(每箱不得超出20双;零头数另行包装),小纸盒外标示型号及批号 及盒内置入立可擦(马上亮皮革油);每只鞋置入1公克乾燥剂再装入透明塑胶袋或不织布鞋 袋. 5-2标志:每个纸箱外面须注明品名,合约案号,型号,数量,包装重量,包装日期,制补单位及每只 鞋内侧腰及每个纸箱外须盖印批号,型号."
"6.备注:"
" 6.1成品图示:(图示仅供参考,依军种确样之样品为主)"
"第13组陆,空军飞行皮靴"
"第13组;第页;共页"
"第13组陆,空军飞行皮靴采购规范"
"第1项:陆军飞行皮靴-PU射出底",,,,,,"第4项:空军新式飞行皮靴-PU射出底"
"第2项:陆军飞行皮靴-橡胶射出底",,,,,,"第5项:空军新式飞行皮靴-橡胶射出底"
"第3项:陆军飞行皮靴-固特异贴底",,,,,,"第6项:空军新式飞行皮靴-固特异贴底"
"编号:MP-304-065A"
"1.适用范围:本规格适用於飞行靴检验用."
"2.适用资料:"
" 2-1材料规格"
" CMS-C-050001 面皮"
" CMS-C-02046a 猪面(里)皮"
" CMS-P-050006 皮鞋里皮"
" CMS-P-050017 鞋用汽眼"
" CMS-C-01144c 人造中底(加纱布)(PU注射)"
" CMS-C-1928a 皮浆中底(橡胶注射)"
" MP-304-019B 皮革拉鍊盘"
" 2-2中国国家标准"
" CNS2779Z4006 计数值检验抽样程序及抽样表"
" CNS734K6047 橡胶磨耗试验标准"
" CNS3555K6346 硫化或热塑性橡胶硬度试验法"
" CNS3553K6344 硫化橡胶拉伸试验法"
" CNS 3689 Z 7043 第6.4.1节 中国国家标准之程式"
"3.品质要求:"
" 3-1成品构造须符合样鞋规定,各项材料检测纪录需备查."
" 3-2鞋面之缝制须良好,线路整齐,无歪斜,跳针,漏缝,脱线,浮线及断线等不良现象,针码每3公"
" 分8-10针,各部线头长度不得超过0.3公分."
" 3-3鞋面面皮须光亮均匀,无破损,刀伤,烫伤等不良现象."
" 3-4鞋底车沿条应扎实紧密,针码每5公分8-10针(固特异贴底);如为注射鞋底应无显著气泡,杂物"
" 等现象,每只鞋底缺胶部分,面积超过0.5X0.5平方公分者不得超过3处,外底边缘应修剪整齐,鞋"
" 底与鞋面接合处胶边余胶部分长度或高度不得超过0.5公分."
" 3-5鞋内不得留有U型钉等异物."
" 3-6鞋面(含后踵部位)上梆须端正,圆顺,不得歪斜及凹凸,齿角等钳帮不良之现象."
" 3-7成品左右鞋高度差异不得超过0.5公分."
" 3-8上胶部分应均匀,且刷胶高度不得超过0.3公分."
" 3-9鞋眼须扎实紧密,无脱落,变形,不牢或缺件."
" 3-10鞋垫须平正贴合,不得有脱落之现象,且裁制大小适中,无皱摺或过小未覆盖中底之现象."
" 3-11每双成品须置入皮革拉鍊盘乙付於包装纸盒内(如军种未要求配置免验)."
" 3-12成品皮革拉链盘须以牛面皮缝合10号古铜拉链或6.5吋黑塑钢拉鍊,缝线针码每3公分8-10针,线"
" 路应整齐,无歪斜,跳针,漏缝,脱线,浮线及断线等不良现象."
" 3-13每双鞋须吊挂保养使用须知,外盒并标示型号并置入纸撑及隔板. "
" 3-14每双港宝须端正置入,不得歪斜,变形塌陷之现象."
" 3-15内里应缝制(贴合)平整牢固,不得有脱开之现象"
" 3-16成品磨粗高度不得超出0.3公分(含)以上(低於0.3公分须整烫平整,喷漆均匀)."
" 3-17成品余胶胶边高度不得超出0.5公分(含)以上."
" 3-18前头须车缝外线一道(本项适用於固特异飞行靴)"
" 3-19鞋面与鞋底间粘合牢固,不得有脱胶开缝之现象."
"4.批之组成:"
" 本规格所谓之批量系指在同一生产工厂,在同一规格,同一时程,同一制程下之产品(最大批量为"
" 10000双)."
"5.抽样与检验:"
" 5-1抽样:"
" 5-1-1外观及包装抽样:依CNS2779 Z 4006实施抽样,使用一般检验水准一级,正常单次抽样计画抽样."
" 5-1-2尺寸检验抽样:依合约委制各型号数量抽取(如鞋楦抽样表),其中1双尺寸不符即全批判定不"
" 合格:尺寸要求如表1."
,,"鞋楦抽样表(每型号)"
,,"批量(双)",,"抽样数"
,,"1~3000",,"1双"
,,"3001~6000",,"2双"
,,"6001以上",,"5双"
" 5-1-3物性检验抽样:依CNS2779Z4006实施抽样,使用特殊检验水准S-1级,正常单次抽样计划,AQL"
" 4.0%抽样计划表."
" 5-2检验:"
" 5-2-1外观及包装检验:严重疵病其中1项疵病即全批判定不合格,主要疵病AQL6.5%,次要疵病AQL"
" 10%(详如下表)"
,"严重疵病","1.型号不符.",,,,,,"目视检查"
,,"2.鞋内U型钉未拔除.",,,,,,"目视检查"
,,"3.成品外观须符合军种确样样鞋.",,,,,,"目视检查"
,,"4.鞋面破损.",,,,,,"目视检查"
,,"5.前头未车缝外线一道(固特异飞行靴).",,,,,,"目视检查"
,"主要疵病","1.皮革拉链盘未以牛面皮缝合10号古铜拉鍊或6.5吋黑塑钢拉",,,,,,"目视检查"
,," 鍊,缝线针码未能每3公分8-10针,线路歪斜,跳针,漏"
,," 缝,脱线,浮线及断线等不良现象."
,,"2.鞋面及后踵上梆歪斜有凹凸,齿角等钳帮不良之现象.",,,,,,"目视检查"
,,"3.鞋面前,后包刀伤致鞋面损伤.",,,,,,"目视检查"
,,"4.包装与标志不符.",,,,,,"目视检查"
,,"5.胶底缺胶,不熟鼓起,表面不平整或成海绵状,脱跟,脱",,,,,,"目视检查"
,," 底(橡胶注射成型)."
,,"6.鞋面与鞋底间粘合不良,有脱胶开缝之现象(宽度或深度",,,,,,"目视及量尺检查"
,," 超过1公分含以上)."
,"次要疵病A级","1.刷胶高度超过0.3公分.",,,,,,"量尺检查"
,,"2.鞋面喷漆未均匀光亮.",,,,,,"目视检查"
,,"3.砸眼不牢,歪斜,脱落,缺件.",,,,,,"目视检查"
,,"4.鞋面缝线针码不正确,线路歪斜,跳针,漏缝,脱线,浮",,,,,,"目视及量尺检查"
,," 线及断线等不良现象,针码每3公分8-10针."
,,"5.车沿条针码每5公分8-10针.",,,,,,"目视检查"
,,"6.港宝未端正置入,有歪斜,变形塌陷之现象.",,,,,,"目视检查"
,,"7.鞋面脏污,沾胶,发霉.",,,,,,"目视检查"
,,"8.缝线处未烧断,线头过长,超过0.3公分.",,,,,,"目视检查"
,,"9.鞋面前,后碰伤及刮伤致鞋面损伤.",,,,,,"目视检查"
,,"10.鞋面与鞋底间粘合不良,有脱胶开缝之现象(宽度或深度",,,,,,"目视及量尺检查"
,," 小於1公分)."
,"次要疵病B级","1.左右鞋高相差超过0.5公分.",,,,,,"量尺检查"
,,"2.鞋底与鞋面接合处胶边余胶部分长度或高度超过0.5公分(",,,,,,"目视及量尺检查"
,," 含)以上."
,,"3.磨粗高度过高,超过0.3公分(含)以上(低於0.3公分须",,,,,,"目视及量尺检查"
,," 整烫平整,喷漆均匀)."
,,"4.鞋垫贴合不平整,有脱落及过大浮鼓或过小未覆盖中底之",,,,,,"目视检查"
,," 现象."
,,"5.内里缝制(贴合)不平整牢固,有脱开之现象.",,,,,,"目视检查"
,,"6.未系(或未置入)皮革拉鍊盘及鞋带或未吊挂保养使用须知",,,,,,"目视检查"
,,"7.每双飞行靴未置入纸撑及隔板.",,,,,,"目视检查"
" 5-2-1-1检验扣点标准:"
" 5-2-1-1-11个主要疵病扣1点,2个次要疵病A级扣1点,3个次要疵病B级扣1点,同1双成品鞋最多扣1点"
" ."
" 5-2-1-1-2同1双成品鞋有1个(含)以上主要疵病,折算扣1点,或有2个(含)以上次要疵病A级或有3"
" 个(含)以上次要疵病B级,折算扣1点."
" 5-2-1-1-3若在不同成品鞋上,其所有疵病数累加计算."
" 5-2-2尺寸检验:依合约委制各型号数量抽取,其中1双尺寸不符即全批判定不合格:尺寸要求如表1."
" 5-2-3物性检验:物性检验需符合物性要求表2."
" 5-2-4检验方法(半成品):"
" 5-2-4-1 PU大底试片及橡胶大底试片:"
" 5-2-4-1-1硬度:依CNS3555K6346法检验之(A型或E型硬度计量测)."
" 5-2-4-1-2伸长率:依CNS3553K6344第3号试验片测试之."
" 5-2-4-1-3抗拉强度:依CNS3553K6344第3号试验片测试之."
" 5-2-4-1-4耐磨性:依CNS734K6047法,磨角15度,荷重2磅检验之."
" 5-2-4-1-5老化试验(橡胶鞋底适用):依CNS3556K6347中「空气加热老化试验」(常态烘箱法)规定"
" ,先将试样以70±3℃做连续加速老化120小时后再依前项第(5-2-4-1-3)节同方法测定其抗"
" 拉强度,并计算老化处理前后之变化率."
" 5-2-5成品检验方法:"
" 5-2-5-1固特异贴底成型剥离力试验:依CNS6863Z2029第8.3节检验之."
" 5-2-5-2成品橡胶注射成型剥离力:先将面皮及后跟割开取下,再自鞋尖中心切割至后踵,将鞋切成两"
" 半作成两样条(不可破坏任何胶底与面皮粘合部分);并将中底清理乾净(避免影响测试之精密"
" 度)再任意取其一样条一端,剥离约40㎜长后,剥离两端分别夹於拉力试验机上,以每分钟"
" 200㎜±2㎜之拉速拉之,取记录值较高一端波状各顶点之胶著荷重之平均值即为剥离力需符合"
" 表 2之要求."
" 5-2-5-3成品铁钉穿透性试验:依CNS6863Z2029第8.8节方法检验.(以100公斤静载重10秒,检查铁钉"
" 是否贯穿鞋底)."
" 5-3但书:1.本项产品(半成品)於进料时检测,成品鉴测时5-2-4-1 PU大底(试片)及橡胶大底(试"
" 片)检验不再实施,惟需提供合格之进料检验纪录备查."
" 2.半成品之获得方式属於采购行为者依采购权责办理."
" 3.本项成品「铁钉穿透性」试验,视委制单位需求办理."
"6.包装与标志:"
" 6-1包装:同批量之包装数须一致(每箱不得超出10双;零头数另行包装)另每双装入小纸盒平放,小"
" 纸盒外须标示型号."
" 6-2标志:每个纸箱外面须注明品名,颜色,型号,批号,数量,单位,包装重量,出厂日期,制补单"
" 位及保固年限(含储存及穿著使用年限):2年,若产品属PU注射成型鞋底,须於每个纸盒"
" ,纸箱外注明「PU鞋底,请於出厂日期后半年内拨发使用」,每只鞋鞋舌内面须盖印型号及"
" 批号."
"7.附表(图) "
,"表1,尺寸要求表:"
,"表2,物性要求表:"
,"PU射出底","硬度",,,"75±5 (E型硬度计测量)"
,,"抗拉强度",,,"30公斤/平方公分(含)以上"
,,"伸长率",,,"300%(含)以上"
,,"耐磨性",,,"0.45立方公分/2000转(含)以下(磨角15度,荷重2磅)"
,"橡胶射出底","硬度",,,"65±5 (A型硬度计测量)"
,,"抗拉强度",,,"140公斤/平方公分(含)以上"
,,"伸长率",,,"400%(含)以上"
,,"耐磨性",,,"0.35立方公分/2000转(含)以下(磨角15度,荷重2磅)"
,,"老化试验",,,"抗拉强度降低率25%以下"
,,"成品剥离力(鞋面与大底间)",,,"5公斤(含)以上(鞋底单边剥离)"
,"固特异贴底","硬度",,,"60±5 (A型硬度计测量)"
,,"抗拉强度",,,"100公斤/平方公分(含)以上"
,,"伸长率",,,"300%(含)以上"
,,"耐磨性",,,"0.35立方公分/2000转(含)以下(磨角15度,荷重2磅)"
,,"成品剥离力(鞋面与大底间)",,,"20公斤(含)以上(全鞋底剥离)"
,"成品铁钉穿透性试验",,,,"100㎏鞋底不得贯穿"
"共6页第2页"
"共6页第4页"
"前 包 "
"后 包 "
"第14组陆军仪队长统皮鞋"
"第14组;第页;共页"
"第14组陆军仪队长统皮鞋采购规范"
"第1项:陆军仪队长统皮鞋"
"编号:MPC-304-020E"
"1.适用范围:本规格适用於三军仪队皮鞋(胶底胶跟或皮底皮跟含天皮)检验用"
"2.使用材料:"
" 2-1面皮(CMS-C-02044)"
" 2-2纸浆中底(CMS-C-01144)"
" 2-3三股合纤线(CMS-C-01422)"
" 2-4缝线胶底含胶跟或缝线皮底皮浆跟含天皮(物性要求如表一)"
" 2-5各种材料检测记录需备查"
"3.品质要求:"
" 3-1鞋面,鞋底,中底型号须一致,成品构造须符合样品规定."
" 3-2鞋面之缝制须良好,线路整齐,无歪斜,跳针,漏缝等现象,针码每公分3-4针,各部线头长度不"
" 得超过0.3公分,且缝线处须烧断."
" 3-3每双成品鞋装入小纸盒,须每只以塑胶袋包装,并罝入1公克乾燥剂一包及要领表."
" 3-4鞋面面皮须光亮均匀,无破损,刀伤,烫伤,碰伤,筋疤,麻点,烙印等不良现象."
" 3-5鞋内不得留有U型钉子等异物."
" 3-6鞋面上梆须端正不得歪斜±0.5公分."
" 3-7左右鞋高度相差应在0.5公分以内."
" 3-8上胶部份应均匀,且刷胶高度不得超过0.3公分."
" 3-9鞋眼须扎实紧密,无脱落,变形,不牢或缺件."
" 3-10鞋内鞋垫须平整,贴牢."
" 3-11每双成品以一双鞋带连接系好."
" 3-12鞋底车外线应扎实紧密,针码每5公分8~10针(另皮大底加贴橡胶底免验,且需加钉10根钉子)."
" 3-13后跟底部天皮须钉8~9根螺纹钉(依军种样品为准)."
" 3-14后跟垫须贴正,贴牢,裁制大小适中,不得有过大皱摺或过小未覆盖中底之现象."
" 3-15鞋面与鞋底贴合,不得有开口,漏缝等不良现象."
" 3-16每双热熔胶片(港宝)处须平整罝入,不得有歪斜,变形塌陷等不良现象."
" 3-17鞋面不得有沾胶,发霉,污染不洁等情形."
"4.批之组成:"
" 本规格所称之批量系指在同生产工厂,同一规格,同一时期,同一制程下之产量(最大批量10000双)"
"5.检验:"
" 5-1外观及包装检查:"
" 5-1-1抽样:依CNS2779Z4006实施抽样,使用一般检验水准一级,正常单次抽样计画,严重疵病:其"
" 中乙项疵病即判定不合格,主要疵病:AQL6.5%,次要疵病:AQL10%(详如下表)"
" 严重疵病",,"1.型号不符",,,,,"目视检查"
,,"2.鞋内钉子未拔除",,,,,"手触及目视检查"
"主要疵病",,"1.鞋面破损,刀伤,烫伤,筋疤,麻点,烙印等不良现象",,,,,"目视检查"
,,"2.鞋面上梆歪斜±0.5公分",,,,,"目视检查"
,,"3.后踵须平整",,,,,"目视检查"
,,"4.砸眼不牢,歪斜,脱落,缺件",,,,,"目视检查"
,,"5.后跟垫未贴正,贴牢,裁制大小不适中,有过大皱摺或过小未覆盖中底之现象",,,,,"目视检查"
,,"6.鞋面与鞋底贴合,有开口,漏缝等不良现象",,,,,"目视检查"
,,"7.每双热熔胶片(港宝)处未平整罝入,有歪斜,变形塌陷等不良现象",,,,,"目视检查"
,,"8.包装与标志及批号不符",,,,,"目视检查"
" 次要疵病A级",,"1.车外线针码每5公分8~10针(或皮大底加贴橡胶底未加钉十跟钉子)",,,,,"量尺及目视检查"
,,"2.缝线针码不对,线路歪斜,跳针",,,,,"目视检查"
,,"3.刷胶高度超过0.3公分",,,,,"量尺量测"
,,"4.鞋垫须平整,无鼓起现象",,,,,"手触及目视检查"
,,"5.后跟底部天皮未钉8~9根螺丝钉(依军种样品为准)",,,,,"目视检查"
,,"6.鞋面脏污,沾胶,发霉",,,,,"目视检查"
"次要疵病B级",,"1.左右鞋高度相差超过0.5公分",,,,,"量尺量测"
,,"2.线头过长超过0.3公分",,,,,"量尺量测"
,,"3.喷漆不均匀或光亮度不够",,,,,"目视检查"
,,"4.缝线处烧断",,,,,"目视检查"
,,"5.未系鞋带",,,,,"目视检查"
,,"6.未置入1公克乾燥剂或要领表",,,,,"目视检查"
" 5-1-2检验扣点标准:"
" 5-1-2-1一个主要疵病扣一点,二个次要疵病A级扣一点,三个次要疵病B级扣一点,同一双成品鞋"
" 最多扣一点."
" 5-1-2-2同一双成品鞋有一个(含)以上主要疵病,折算扣一点,或有二个(含)以上次要疵病A级"
" ,或有三个次要疵病B级,折算扣一点."
" 5-1-2-3若在不同成品鞋上,其所有疵病数累加计算."
" 5-2物性检验:"
" 5-2-1抽样:依CNS2779Z4006实施抽样,使用特殊检验水准S-1级,正常单次抽样计划,AQL10%抽样计"
" 划表,物性要求如表一."
" 5-2-2检验方法:"
" 5-2-2-1硬度:依CNS3555K6346法A型硬度计检验之."
" 5-2-2-2伸长率:依CNS3553K6344第3号试验片测试之."
" 5-2-2-3抗拉强度:依CNS3553K6344第3号试验片测试之."
" 5-2-2-4耐磨性:依CNS734K6047检验之,磨角15度,荷重2磅."
" 5-3尺寸检验:"
" 5-3-1抽样:於量产前依CNS2779Z4006实施抽样,量测鞋楦尺寸,使用特殊检验水准S-1级,单次抽样"
" 计划,AQL6.5%抽样计划表,尺寸要求如表二,产品鉴测时不再实施."
" 5-4但书:本项产品(半成品)於进料时检测,成品鉴测时5-2-2大底物性检验不再实施,惟需提供合"
" 格之进料检验纪录备查(惟外包产品之购料应送至军品鉴测处检验.有军品鉴测处之进料检"
" 验合格报告者,鉴测时就不再对原料进行检验;无军品鉴测处之进料检验合格报告者,鉴测"
" 时仍需由军品鉴测处依规格实施原料之检验."
"6.包装与标志:"
" 6-1包装:每箱装10双,每双装入小纸盒平放,小纸盒外须标示型号."
" 6-2标志:每个纸箱外面须注明品名,颜色,型号,批号,数量,单位,包装重量,出厂日期,制补单"
" 位及储存年限:二年,每只鞋鞋舌内面须盖印型号及批号."
"7.参考资料:"
" CNS2779Z4006 CMS-C-02044 CMS-C-01422 CMS-C-02044"
" CMS-C-01633 CNS3555K6346 CNS3553K6344 CNS734K6047"
"8.附表(图):"
"表一,物性要求表"
,"硬度",,,"75±5"
,"伸长率",,,"310%(含)以上"
,"抗拉强度",,,"105公斤/平方公分(含)以上"
,"耐磨性",,,"0.2立方公分/2000转(含)以下(磨角15度,荷重2磅)"
"表二,尺寸要求表"
"图一,成品图"
"第15组空军军乐队皮鞋"
"第15组;第页;共页"
"第15组空军军乐队皮鞋采购规范"
"第1项:空军军乐队半高统马靴-橡胶登山底",,,,,"第2项:空军军乐队半高统马靴-三合一组合底"
"编号:MP-304-038D"
"1.适用范围:本规格适用於双拉鍊半高统马靴(登山底或皮大底)及军乐队半高统马靴("
" 三合一组合底或皮大底)检验用."
"2.使用材料:(本节说明制作时所用之主要材料及规格)"
" 2-1面皮(CMS-C-02044b)或可丽柔漆皮(CMS-C-02021)"
" 2-2猪面里皮(CMS-C-02046a)"
" 2-3纸浆中底(CMS-C-01144c)"
" 2-4黄牛底皮(CMS-C-00708)"
" 2-5橡胶登山鞋底或三合一组合底(物性要求如表二)"
" 2-6各种材料检测记录需备查"
"3.品质要求:"
" 3-1鞋面,鞋底,型号须符合一致,成品构造须符合样品规定."
" 3-2成品大底总成沿条不得脱落及脱底之现象(适用於登山底)."
" 3-3鞋面之缝制须良好,线路整齐,无歪斜,跳针,漏缝,脱线,浮线及断线等不良现象,针码每公分"
" 4-5针及各部线头长度不得超过0.5公分."
" 3-4鞋面面皮须光亮均匀无破损,刀伤,烫伤,碰伤及不得有筋疤,麻点,烙印,不平整等不良现象."
" 3-5鞋舌内里盖印型号及批号不得模糊不清,无法辨认."
" 3-6鞋内不得留有U型钉等异物."
" 3-7鞋面上梆(含后踵部份)须端正圆顺不得歪斜(±0.5公分以内)及凹凸,齿角等钳帮不良现象."
" 3-8左右鞋高度相差应在0.5公分以内."
" 3-9鞋面及鞋底间贴合不可有脱胶,开口之现象."
" 3-10抹胶部份应均匀,且刷胶高度不得超过0.3公分."
" 3-11成品部位(含内里)不得有沾胶,发霉,污染不洁等情形."
" 3-12鞋内里皮,中底须平整,缝牢."
" 3-13鞋垫须贴正,贴牢,不得有歪斜,脱落之现象."
" 3-14每双成品单只装入透明塑胶袋内,另一只亦放透明塑胶袋内,以避免磨擦,每个塑胶袋内装入(1"
" 公克)乾燥剂."
" 3-15成品鞋面双边拉鍊需平顺且不得损坏."
" 3-16鞋面各部位需平整,无皱摺,龟裂等现象."
"4.批之组成:"
" 本规格所称之批量系指在同生产工厂,同一规格,同一时期,同一制程下之产量.(最大批量35000双)"
"5.检验:"
" 5-1外观及包装检查:"
" 5-1-1抽样:依CNS2779Z4006实施抽样,使用一般检验水准一级,正常单次抽样计画,严重疵病(其"
" 中乙项疵病即全批判定不合格),主要疵病AQL6.5%,次要疵病AQL10%,详如下表"
" 严重疵病",,"1.成品构造与样品不符",,,,,,"目视检查"
,,"2.大底总成沿条脱落,脱底(适用於登山底)",,,,,,"目视检查"
,,"3.鞋面破损,刀伤,烫伤等不良现象",,,,,,"目视检查"
,,"4.鞋内钉子未拔除",,,,,,"手触及目视检查"
,,"5.拉鍊损坏",,,,,,"目视检查"
" 主要疵病",,"1.鞋面面皮不光亮均匀",,,,,,"目视检查"
,,"2.鞋面及鞋底间贴合有脱胶,开口之现象",,,,,,"手触及目视检查"
,,"3.中底未平整,鼓起现象",,,,,,"目视检查"
,,"4.鞋里皮未紧贴面皮,浮起现象",,,,,,"目视检查"
,,"5.鞋面各部位不平整(起角),有皱摺,龟裂等现象",,,,,,"目视检查"
"次要疵病A级",,"1.鞋面脏污,沾胶,发霉",,,,,,"目视检查"
,,"2.缝线针码不对,线路歪斜,跳针,漏缝,脱线,浮线及断线",,,,,,"目视检查"
,,"3.鞋面有筋疤,麻点,烙印,等不良现象",,,,,,"目视检查"
,,"4.包装与标志及批号不符",,,,,,"目视检查"
,,"5.鞋舌内里未盖印型号及批号",,,,,,"目视检查"
,,"6.左右鞋高度相差超过0.5公分",,,,,,"量尺量测"
,,"7.鞋面上梆歪斜±0.5公分",,,,,,"目视检查"
" 次要疵病B级",,"1.未置入乾燥剂及装於透明塑胶袋内",,,,,,"目视检查"
,,"2.刷胶高度超过0.3公分",,,,,,"卡尺量测"
,,"3.缝线处未烧断",,,,,,"目视检查"
,,"4.鞋垫未贴正,贴牢,歪斜,脱落现象",,,,,,"目视检查"
,,"5.线头过长超过0.5公分",,,,,,"卡尺量测"
,,"6.批号模糊不清",,,,,,"目视检查"
" 5-1-2检验扣点标准:"
" 5-1-2-1一个主要疵病扣一点,二个次要疵病A级扣一点,三个次要疵病B级扣一点,同一双成品鞋最"
" 多扣一点."
" 5-1-2-2同一双成品鞋有一个(含)以上主要疵病,折算扣一点,或有二个(含)以上次要疵病A级或"
" 有三个次要疵病B级,折算扣一点."
" 5-1-2-3若在不同成品鞋上,其所有疵病数累加计算."
" 5-2尺寸检验:"
" 5-2-1抽样:每型号至少抽取乙双,每批抽取数不得少於八双,其中乙双尺寸不符即全批判定不合格."
" 5-3物性检验:"
" 5-3-1抽样:依CNS2779Z4006实施抽样,使用特殊检验水准S-1级,正常单次抽样计划,AQL4.0%抽样计"
" 划表."
" 5-3-2检验方法:"
" 5-3-2-1橡胶大底及三合一组合底:"
" 5-3-2-1-1硬度:依CNS 3555 K 6346法萧氏A型硬度计检验."
" 5-3-2-1-2抗拉强度:依CNS 3553 K 6344法以3号试验片检验."
" 5-3-2-1-3伸长率:依CNS 3553 K 6344法以3号试验片检验."
" 5-3-2-1-4耐磨性:依CNS 734 K 6047法,荷重2磅,角度15°检验."
" 5-3-2-2成品剥离力:裁取鞋底试样,仅留鞋底及面皮粘合部分为1.5～2.5公分之宽度,将面皮与鞋底"
" 分开5公分长,分别夹於拉力试验机上,以每分钟200㎜±2㎜之拉速拉之,求取平"
" 均值."
" 5-3-2-3成品弯折试验:取试样二双,后跟及前掌部份分别固定於鞋子弯折试验机上,调整机器前掌板"
" 动角度40～50度,速度为每分钟90～100次,注意PVC沿条与胶底间是否有"
" 脱开或任何龟裂现象."
" 5-4但书:1.本项产品(半成品)於进料时检测,成品鉴测时5-3-2-1-1硬度,5-3-2-1-2伸长率,"
" 5-3-2-1-3抗拉强度,5-3-2-1-4耐磨性等四项检验不再实施,惟需提供合格之进料检验纪"
" 录备查."
" 2.半成品之获得方式属於采购行为者,则应於产品鉴测时提供符合「军事机关财物劳务采购"
" 作业规定」合格进料检验纪录备查."
"6.包装与标志:"
" 6-1包装:每箱装12双,箱内每双用小纸盒包装,并注明型号."
" 6-2标志:每个纸箱外面须注明品名,颜色,提制文号,型号,数量,单位,包装重量,出厂日期,制"
" 补单位."
" 6-3批号:每只鞋鞋舌内面及每个纸箱外右上方须盖印批号."
"7.参考资料:"
" CNS2779Z4006 CMS-C-02044 CMS-C-02021 CMS-C-01770"
" CMS-C01252 CMS-C-01144 CMS-C-00708 CNS3555K6346"
" CNS3553K6344 CNS734K6047"
"8.附图(表):"
"表一,尺码表"
,"备 注","一,单位:㎜,公差±1.5㎜"
,,"二, 尺寸依CNS4799S1092检验,以楦头量测",,,,," "," A"
,,"AB:楦头底面长度 "
,,,,,,,," B"
"表二,物性要求表"
,"橡胶登山底","硬度",,,,,"70±5"
,,"伸长率",,,,,"250%(含)以上"
,,"抗拉强度",,,,,"120公斤/平方公分(含)以上"
,,"耐磨性",,,,,"0.4立方公分/2000转(含)以下"
,,"成品剥离力",,,,,"7公斤(含)以上"
,,"成品弯折试验",,,,,"试验鞋面与沿条及大底间10万次(含)以上无剥离现象"
,"三合一组合底","硬度",,,,,"70±5"
,,"伸长率",,,,,"250%(含)以上"
,,"抗拉强度",,,,,"120公斤/平方公分(含)以上"
,,"耐磨性",,,,,"0.4立方公分/2000转(含)以下"
,,"成品剥离力",,,,,"7公斤(含)以上"
,,"成品弯折试验",,,,,"试验鞋面与沿条及大底间10万次(含)以上无剥离现象"
"图一,成品图示:"
""
"共5页第5页 "
"共5页第5页 "
"第16组钢包头安全鞋"
"第16组;第页;共页"
"第16组钢包头安全鞋采购规范"
"第1项:钢包头安全鞋",,,,,"第2项:钢包头安全鞋(H级)"
"第3项:钢包头安全防滑鞋",,,,,"第4项:钢包头安全防滑鞋(H级)"
"编号:MP-304-026G"
"1.适用范围:本规格适用於钢包头安全鞋及钢包头安全运动鞋检验用."
"2.使用材料:"
" 2-1面皮(CMS-C-2044b)"
" 2-2人造中底(加纱布)(CMS-C-1144c)"
" 2-3皮革制安全鞋(CNS6863Z2029)"
" 2-4 PU鞋底或橡胶鞋底(物性如表一)"
" 2-5各项材料检测纪录需备查"
"3.品质要求:"
" 3-1鞋面,鞋垫,型号须符合一致,成品构造须符合样品规定."
" 3-2鞋面之缝制须良好,线路整齐,无歪斜,跳针等现象,针码每公分3-4针,各部线头长度不得超过"
" 0.3公分(含)."
" 3-3鞋面面皮须光亮均匀,无破损,刀伤及皱摺等不良现象."
" 3-4鞋内不得留有U型钉,线头等异物."
" 3-5鞋面与鞋底贴合须端正,不得歪斜,且刷胶高度不可超过0.5公分."
" 3-6鞋底车外线每5公分4-5针(PU鞋底免验)."
" 3-7成品不得有发霉,污染不洁等情形."
" 3-8每双成品须内置一双鞋垫须贴牢,不得有不平整,歪斜等现象"
" 3-9左右鞋高度相差应该在1公分(含)以内."
" 3-10每双成品须以一双鞋带连接系好,以包装纸或塑胶袋相对包装於纸盒内,不得碰撞,刮伤."
" 3-11成品内须置入1公克乾燥剂."
" 3-12鞋面上帮须端正不得左右歪斜0.5公分(含)."
" 3-13鞋底贴合需牢固,不得有开缝脱胶."
" 3-14鞋眼须扎实紧密,无脱落,变形,松动不牢或缺件."
" 3-15鞋内里不可起皱打摺及贴合不良之现象."
" 3-16钢包头内面接合之材料,应贴合平顺,牢固,不可有包空,脱落之现象."
" 3-17护趾钢包头需平正置入,不得歪斜,松动."
"4.批之组成:"
" 本规格所谓之批量系指在同生产工厂,在同一规格,同一时期,同一制程下之产品.(最大批量为"
" 50000双) "
"5.检验:"
" 5-1外观及包装检查:"
" 5-1-1抽样:依CNS2779Z4006实施抽样,使用一般检验水准一级,正常单次抽样计画,严重疵病其中"
" 乙项疵病即全批判定不合格,主要疵病AQL6.5%,次要疵病AQL10%详如下表"
,"严重疵病","1.成品构造与样品不符",,,,,,"目视检查"
,,"2.鞋面破损,刀伤",,,,,,"目视检查"
,,"3.护趾钢包头需平正置入,不得歪斜,松动",,,,,,"目视检查"
,,"4.鞋内留有U型钉",,,,,,"目视检查"
,"主要疵病","1.鞋面上帮不得左右歪斜0.5公分(含)",,,,,,"量尺检查"
,,"2.鞋底贴合开缝脱胶超过5公分(含)以上",,,,,,"量尺检查"
,,"3.成品发霉",,,,,,"目视检查"
,,"4.钢包头内面所接合之材料,未贴合平顺,有皱摺,包空之现象",,,,,,"目视检查"
,,"5.鞋眼未扎实紧密,有脱落,歪斜,变形,松动不牢及缺件",,,,,,"目视检查"
,"次要疵病A级","1.包装与标志不符",,,,,,"目视检查"
,,"2.缝线针码不对,歪斜,跳针,浮线,漏线,脱线,针码每公分3-4针",,,,,,"目视及量尺检查"
,,"3.鞋底车外线每5公分4-5针",,,,,,"量尺检查"
,,"4.鞋面与鞋底贴合不正",,,,,,"目视检查"
,,"5.刷胶高度超过0.5公分(含)",,,,,,"量尺检查"
,,"6.鞋内里起皱打摺及贴合不良之现象",,,,,,"目视检查"
,,"7.成品粘胶,污染不洁等情形",,,,,,"目视检查"
,,"8.鞋面喷漆亮度不均匀及皱摺现象",,,,,,"目视检查"
,,"9.鞋底贴合开缝脱胶小於5公分",,,,,,"量尺检查"
,"次要疵病B级","1.成品未置入鞋垫及贴牢,不平整,歪斜现象",,,,,,"目视检查"
,,"2.左右鞋高度相差超过1(含)公分",,,,,,"量尺检查"
,,"3.线头过长超过0.3(含)公分",,,,,,"量尺检查"
,,"4.未置入1公克乾燥剂",,,,,,"目视检查"
,,"5.鞋面,鞋垫,型号须符合一致",,,,,,"目视检查"
" 5-1-2检验扣点标准:"
" 5-1-2-1一个主要疵病扣一点,二个次要疵病A级扣一点,三个次要疵病B级扣一点,同一双成品鞋最多"
" 扣一点."
" 5-1-2-2同一双成品鞋有一个(含)以上主要疵病折算扣一点,或有二个(含)以上次要疵病A级或有三个"
" 以上次要疵病B级折算扣一点."
" 5-1-2-3若在不同成品鞋上,其所有疵病数累加计算. "
" 5-2物性检验:"
" 5-2-1抽样:依CNS2779Z4006实施抽样,使用特殊检验水准S-1级,正常单次抽样计画AQL4.0%,物性"
" 要求如表一."
" 5-2-2检验方法:"
" 5-2-2-1成品检验:"
" 5-2-2-1-1成品耐压扁试验:依CNS 6863 Z 2029 第8.1节,压扁荷重1400公斤."
" 5-2-2-1-2成品耐冲击试验:依CNS 6863 Z 2029 第8.2节,重锤质量23公斤,落下高度450㎜."
" 5-2-2-1-3成品剥离性试验:依CNS6863Z2029第8.3节."
" 5-2-2-1-4成品铁钉穿透性试验:依CNS6863Z2029第8.8节(若无加钢片则免验)."
" 5-2-2-1-5鞋底(含后跟)最薄厚度量测试验:依CNS6863Z2029第8.6(1)节."
" 5-2-2-2材料试片检验:"
" 5-2-2-2-1橡胶鞋底检验:"
" 5-2-2-2-1-1硬度:依CNS3555K6346法A型硬度计检验之."
" 5-2-2-2-1-2伸长率:依CNS3553K6344第3号试验片测试之."
" 5-2-2-2-1-3抗拉强度:依CNS3553K6344第3号试验片测试之."
" 5-2-2-2-1-4耐磨性:依CNS734K6047检验之."
" 5-2-2-2-1-5鞋底(含后跟)最薄厚度量测试验:依 CNS 6863Z2029第8.6(1)节."
" 5-2-2-2-2 PU鞋底检验:鞋底材料之物理性能试验按下列各项施行之,但试片须由鞋底之聚胺酯泡棉"
" 层制成;但重叠胶合之合成橡胶试片则用与成品鞋底同一材料或成品取下制成之."
" 5-2-2-2-2-1抗拉试验:依CNS3553K6344第2号试验片测试之."
" 5-2-2-2-2-2撕裂试验:依CNS3559K6350第B型试验片测试之."
" 5-2-2-2-2-3老化试验:依CNS3556K6347第2.1节(温度70℃±1℃,120小时)2号试验片测试之.(参"
" 考CNS12708Z2078第8.8.3节)"
" 5-2-2-2-2-4比重试验:依CNS5341K6458法之规定."
" 5-2-2-2-2-5耐油性试验:依CNS3562K6353中之试验方法试算出体积变化率,但试验用油为NO.3油,试"
" 验用油温度40±1 C,浸泡时间为22小时.(参考CNS12708Z2078第8.8.5节)"
" 5-3尺寸检验:"
" 5-3-1抽样:各型号依合约批量抽取(如鞋楦抽样表),其中乙双尺寸不符即全批判定不合格:尺寸要"
" 求如表一. "
,,"鞋楦抽样表","批量(双)",,,"抽样数(每型号)"
,,,"1~10000",,,"1双"
,,,"10001~30000",,,"2双"
,,,"30001~50000",,,"3双"
" 5-3-2尺寸要求:如表二."
" 5-4但书:1.本项产品(半成品)於进料时检测,成品鉴测时半成品检验不再实施,惟需提供合格之进"
" 料检验纪录备查."
" 2.半成品之获得方式属於采购行为者依采购权责办理."
"6.包装与标志:"
" 6-1包装:采用一般商业包装,同批量之包装数须一致(零头数另行包装)."
" 6-2标志:每个纸箱外面须注明品名,颜色,型号,批号,数量,单位,包装重量,出厂日期,制补单"
" 位及保固年限(含储存及穿著使用年限):二年,每只鞋鞋舌内面须盖印型号及批号."
"7.参考资料:"
" CNS2779Z4006 计数值检验抽样程序及抽样表"
" CNS6863Z2029 皮革制安全鞋"
" CNS3555K6346 硫化橡胶硬度试验法"
" CNS3553K6344 硫化橡胶拉伸试验法"
" CNS734K6047 橡胶磨耗试验标准"
" CNS3559K6350 硫化橡胶抗撕裂强度试验法"
" CNS3556K6347 硫化橡胶老化试验法"
" CNS5341K6458 硫化橡胶密度之测定法"
" CNS3562K6353 硫化橡胶浸渍试验法"
" CNS4799S1092 橡胶底帆布鞋及全橡胶鞋之标准铸模尺度"
" CNS4801S1094 皮鞋楦头之标准尺度"
" CNS12708Z2078 发泡聚胺酯鞋底安全鞋"
" CMS-C-1144c 人造中底(加纱布)"
"8.附表(图): "
"图一,成品图:钢包头安全鞋"
"图二,成品图:钢包头安全鞋(H)级"
"表一,物性要求表"
,"成品","耐压扁试验",,,"中底和护趾钢头间之空隙必须有15㎜(含)以上."
,,"耐冲击试验",,,"中底和护趾钢头间之空隙必须有15㎜(含)以上."
,,"剥离力试验(鞋底与鞋面间)",,,"30㎏(含)以上."
,,"耐铁钉穿透性",,,"鞋底不得贯穿."
,,"鞋底最薄厚度(鞋底含后跟)",,,"鞋底最薄部,测试厚度须为3.0㎜(含)以上.(H级鞋底最薄部,测试厚度须为3.5㎜(含)以上)"
,"橡胶鞋底","硬度",,,"70±5"
,,"抗拉强度",,,"140公斤¤平方公分(含)以上."
,,"伸长率",,,"300%(含)以上."
,,"耐磨性",,,"0.3立方公分¤ 2000转(含)以下(以磨角15度,荷重2磅)."
,,"鞋底最薄厚度(鞋底含后跟)",,,"鞋底最薄部,测试厚度须为3.0㎜(含)以上.(H级鞋底最薄部,测试厚度须为3.5㎜(含)以上)"
,"PU鞋底","抗 拉 强 度",,,"抗拉强度",,"60公斤¤平方公分(含)以上."
,,,,,"伸长率",,"300%(含)以上."
,,"撕裂试验",,,"25公斤¤公分(含)以上."
,,"老化试验",,,"抗拉强度之变化率±20%以内."
,,"比重试验",,,"0.5(含)以上."
,,"耐油性试验",,,"体积变化率+10%,-0%"
"表二,尺码表"
,"备注","一.单位:㎜,公差±2㎜ "
,,"二.底长依CNS4799S1092法,量测由A点至B点之楦头底面之长度."
,,"三.楦头周径尺度依CNS4801S1094法,量测由B点绕鞋面一周至C点,测定其距离."
,,"四.型号未明订之底长及楦头周径尺寸则依比例大小级放."
,,"(1)底长",,"A"
,," "
,,,,"B"
,,"(2)楦头周径"
·下一篇：运动的重要