iR3300数码复印机的维修调整\"  文件类型：XLS/Microsoft Excel   文件大小：字节

\"iR2200;iR2800;iR3300数码复印机的维修调整\"
\"制作:WGF\"
\"共页 ,第页\"
,,\"CANON 佳能 iR2200/iR2800/iR3300 数码复印机维修/调整\"
,,\"定期维修周期\",,,,,,,\"每12万印张进行一次\"
,,\"维修程序模式进入法:\",,,,,,,\"按面板操作部的用户方式(星号\\\"*\\\")键→同时按住数字键\\\"2\\\"和\\\"8\\\"→再按面板操作部的用户方式(星号\\\"*\\\")键\"
,,\"打印维修模式一览表\",,,,,,,\"COPIER>FUNCTION>MISC-P>LBL-PRNT\",,,,,,,,,,\"用手进纸盒,选择LBL-PRNT显示反转后按OK键,打印出一张维修模式一览表\"
,,\"打印维修模式设定值的一览表\",,,,,,,\"COPIER>FUNCTION>MISC-P>P-PRINT\",,,,,,,,,,\"选择P-PRINT,显示反转后按OK键,打印出打印维修模式一览表\"
,,\"打印操作面板的按键输入记录\",,,,,,,\"COPIER>FUNCTION>MISC-P>KEY-HIST\",,,,,,,,,,\"选择KEY-HIST,显示反转后按OK键,打印出操作面板的按键输入记录\"
,,\"打印卡纸记录/出错代码记录\",,,,,,,\"COPIER>FUNCTION>MISC-P>HIST-PRT\",,,,,,,,,,\"选择HIST-PRT,显示反转后按OK键,打印出维修模式的卡纸记录/出错代码记录\"
,,\"打印用户模式一览表\",,,,,,,\"COPIER>FUNCTION>MISC-P>USER-PRT\",,,,,,,,,,\"选择USER-PRT,显示反转后按OK键,打印出用户模式一览表\"
,,\"故障码清除:\",,,,,,,\"选择ERR,显示反转后按OK键盘(全部操作要在3秒内完成),再将主电源开关OFF/ON \"
,,\"用户设定的[规格设定/密码模式/部门ID/模式记忆等]后备数据的清除\"
,,,,,,,,,\"COPIER>FUNCTION>CLEAR>MMI\",,,,,,,,,,\"选择MMI,显示反转后按OK键;OFF/ON主电源开关\"
,,\"E000～E004定影故障码清除:\",,,,,,,\"COPIER>FUNCTION>CLEAR>ERR \",,,,,,,,,,\"选择ERR,显示反转后按OK键盘,再将主电源开关OFF/ON \"
,,\"E032清除:\",,,,,,,\"COPIER>FUNCTION>CLEAR>ERR \",,,,,,,,,,\"选择ERR,显示反转后按OK键盘,再将主电源开关OFF/ON 清除故障码\"
,,\" E717清除:\",,,,,,,\"COPIER>FUNCTION>CLEAR>ERR \",,,,,,,,,,\"选择ERR,显示反转后按OK键盘,再将主电源开关OFF/ON 清除故障码\"
,,\"E345清除\",,,,,,,\"COPIER>FUNCTION>CLEAR>E345-CLR\",,,,,,,,,,\"选择E345-CLR,显示反转后按OK键;OFF/ON主电源开关,清除E345\"
,,\"E355清除\",,,,,,,\"COPIER>FUNCTION>CLEAR>E355-CLR\",,,,,,,,,,\"选择E355-CLR,显示反转后按OK键;OFF/ON主电源开关,清除E355\"
,,\"清除维修模式的后备数据\",,,,,,,\"COPIER>FUNCTION>CLEAR>SERVICE\",,,,,,,,,,\"选择SERVICE,显示反转后按OK键;OFF/ON主电源开关\"
,,\"清除卡纸记录\",,,,,,,\"COPIER>FUNCTION>CLEAR>JAN-HIST\",,,,,,,,,,\"选择JAM-HIST,显示反转后按OK键;OFF/ON主电源开关\"
,,\"清除出错记录\",,,,,,,\"COPIER>FUNCTION>CLEAR>ERR-HIST\",,,,,,,,,,\"选择ERR-HIST,显示反转后按OK键;OFF/ON主电源开关\"
,,\"用户模式[系统管理]密码的清除\",,,,,,,\"COPIER>FUNCTION>CLEAR>PWD-CLR\",,,,,,,,,,\"选择PWD-CLR,显示反转后按OK键;OFF/ON主电源开关\"
,,\"主控板计数的维修计数器的清除\",,,,,,,\"COPIER>FUNCTION>CLEAR>CNT-MCON\",,,,,,,,,,\"选择CNT-MCON,显示反转后按OK键;OFF/ON主电源开关\"
,,\"DC板计数的维修计数器的清除\",,,,,,,\"COPIER>FUNCTION>CLEAR>CNT-DCON\",,,,,,,,,,\"选择CNT-DCON,显示反转后按OK键;OFF/ON主电源开关\"
,,\"计数器清除步骤:\",,,,,,,\"COPIER>COUNTER>××××>××××\",,,,,,,,,,\"选择要清除的××××计数器项目,该项目显示反转后按清除键,\"
,,\"定期更换/消耗品零部件(定期更换PRDC-1/消耗品零部件DRBL-1/消耗品零部件DRBL-2)计数器的检查: \"
,,\"例:TR-ROOL / 00000201 / 00240000 / 0% !! 000082\"
,,\"TR-ROOL,零部件名称, 本例中的TR-ROOL为转印电极辊\"
,,\"00000201 为转印电极辊计数器实际已使用张数 (该零部件更换后要将该计数器清除)\"
,,\"00240000 为转印电极辊零部件寿命限定的使用张数 \"
,,,,\"(在该项目中的数据可以设定,数据设定后按\\\"OK\\\"键)\"
,,\"0% 为实际使用张数与限定使用张数的比值,\"
,,\"!! 为实际使用张数与限定使用张数的比值达到90～100%时显示1个 ! ;超过100%时显示2个 !! \"
\" \",\" \",\"000082 为预计在82天后需要更换转印电极辊零部件. \"
,,\"检查图像位置\",,,,,,,,,,,,,,,,\"3-3T\"
,,,\"纸盒前/后位置调整(图像横向对位调整),\"
,,,\"首先用下例维修模式调整,如果不能解决问题,可分别调整每个纸盘的机械位置(每个刻多度大约1毫米)\"
,,,\"纸盒1水平(横向)对位自动调整\",,,,,,,\"COPIER>FUNCTION>MISC-P>C1-ADJ-Y\",,,,,,,,,\"选择C1-ADJ-Y显示反转后按OK键,从纸盒1输纸打印出一张半色调PG图像\"
,,,,,,\"2.5±1.5毫米\",,,,,,,,,,,,,\"同时水平对位传感器PS11测试移动量,并把数据存入内存储器\"
,,,\"纸盒2水平(横向)对位自动调整\",,,,,,,\"COPIER>FUNCTION>MISC-P>C2-ADJ-Y\",,,,,,,,,\"选择C2-ADJ-Y显示反转后按OK键,从纸盒2输纸打印出一张半色调PG图像\"
,,,,,,\"2.5±1.5毫米\",,,,,,,,,,,,,\"同时水平对位传感器PS11测试移动量,并把数据存入内存储器\"
,,,\"纸盒3水平(横向)对位自动调整\",,,,,,,\"COPIER>FUNCTION>MISC-P>C3-ADJ-Y\",,,,,,,,,\"选择C3-ADJ-Y显示反转后按OK键,从纸盒3输纸打印出一张半色调PG图像\"
,,,,,,\"2.5±1.5毫米\",,,,,,,,,,,,,\"同时水平对位传感器PS11测试移动量,并把数据存入内存储器\"
,,,\"纸盒4水平(横向)对位自动调整\",,,,,,,\"COPIER>FUNCTION>MISC-P>C4-ADJ-Y\",,,,,,,,,\"选择C4-ADJ-Y显示反转后按OK键,从纸盒4输纸打印出一张半色调PG图像\"
,,,,,,\"2.5±1.5毫米\",,,,,,,,,,,,,\"同时水平对位传感器PS11测试移动量,并把数据存入内存储器\"
,,,\"手进纸盒水平(横向)对位自动调整\",,,,,,,\"COPIER>FUNCTION>MISC-P>MF-ADJ-Y\",,,,,,,,,\"选择MF-ADJ-Y显示反转后按OK键,从手进纸盒输纸打印出一张半色调PG图像\"
,,,,,,,,,,,,,,,,,,,\"同时水平对位传感器PS11测试移动量,并把数据存入内存储器\"
,,,\"侧纸仓(L1)水平(横向)对位自动调整\",,,,,,,\"COPIER>FUNCTION>MISC-P>DK-ADJ-Y\",,,,,,,,,\"选择DK-ADJ-Y显示反转后按OK键,从侧纸仓(L1)输纸打印出一张半色调PG图像\"
,,,,,,\"2.5±1.5毫米\",,,,,,,,,,,,,\"同时水平对位传感器PS11测试移动量,并把数据存入内存储器\"
,,,\"打印出一张维修模式一览表\",,,,,,,\"COPIER>FUNCTION>MISC-P>LBL-PRNT\",,,,,,,,,\"用手进纸盒,选择LBL-PRNT显示反转后按OK键,打印出一张维修模式一览表\"
,,,\"纸盒1激光写开始位置调整\",,,,,,,\"COPIER>ADJUST>MISC>C1-ADJ-Y\",,,,,,,,,\"调整范围-32～ 32,每步0.16毫米\"
,,,\"纸盒2激光写开始位置调整\",,,,,,,\"COPIER>ADJUST>MISC>C2-ADJ-Y\",,,,,,,,,\"调整范围-32～ 32,每步0.16毫米\"
,,,\"纸盒3激光写开始位置调整\",,,,,,,\"COPIER>ADJUST>MISC>C3-ADJ-Y\",,,,,,,,,\"调整范围-32～ 32,每步0.16毫米\"
,,,\"纸盒4激光写开始位置调整\",,,,,,,\"COPIER>ADJUST>MISC>C4-ADJ-Y\",,,,,,,,,\"调整范围-32～ 32,每步0.16毫米\"
,,,\"手进纸盒激光写开始位置调整\",,,,,,,\"COPIER>ADJUST>MISC>MF-ADJ-Y\",,,,,,,,,\"调整范围-32～ 32,每步0.16毫米\"
,,,\"侧纸仓(L1)激光写开始位置调整\",,,,,,,\"COPIER>ADJUST>MISC>DK-ADJ-Y\",,,,,,,,,\"调整范围-32～ 32,每步0.16毫米\"
,,,\"双面再进纸时横向对位调整\",,,,,,,\"COPIER>ADJUST>FEED-ADJ>ADJ-REFE\",,,,,,,,,\"调整范围-100～ 100\",,,,,\"每步0.1毫米\"
,,,\"横向对位检测动作\",,,,,,,\"1,横向对位传感器的原位位置检测:当主电源开关ON,或卡纸复位期间,或前门开关关闭时检测\"
,,,,,,,,,,\"2,横向对位传感器的检测开始位置检测:检测开始位置是当对位传感器PS10 ON时,参考手进纸盘纸宽挡板和纸盘纸尺寸数据,\"
,,,,,,,,,,\" 驱动横向对位传感器步进电机M3将横向对位传感器移到离开纸横向边缘大约10毫米处\"
,,,,,,,,,,\"3,当对位传感器PS10检测到纸前沿后,横向对位传感器步进电机M3向横向对位检测开始位置移动,\"
,,,,,,,,,,\" 从横向对位检测开始位置到纸的横向边缘大约可移动10毫米,根据横向对位传感器步进电机M3每个脉冲大约移动0.16毫米来确定纸实际位置\"
,,\"进纸对位置调整(对位离合器ON时序调整)\"
,,,\"对位离合器ON时序调整\",,,,,,,,,\"COPIER>ADJUST>FEED-ADJ>REGIST\",,,,,,,,,\"调整范围-600～ 600,每步0.1毫米,数据大对位离合器ON时序延迟\"
,,\"图像前/后位置调整(图像横向对位调整)\"
,,,\"主扫描方向图像读取开始位置调整\",,,,,,,,,\"COPIER>ADJUST>ADJ-XY>ADJ-Y\",,,,,,,,,\"调整范围100～400,每12步1毫米,标准2.5±2.0毫米,数据大移向前边\"
,,,\"DADF主扫描方向图像读取开始位置调整\",,,,,,,,,\"COPIER>ADJUST>ADJ-XY>ADJ-Y-DF\",,,,,,,,,\"调整范围100～400\",,,,\"每步0.1毫米\"
,,\"图像前沿空白调整\"
,,,\"扫描器图像前沿开始位置调整\",,,,,,,,,\"COPIER>ADJUST>ADJ-XY>ADJ-X\",,,,,,,,,\"调整范围250～290,每12步1毫米,标准2.5±2.0毫米,数据大移向后移\"
,,,\"光学扫描原位位置调整(原位传感器PS400)\",,,,,,,,,\"COPIER>ADJUST>ADJ-XY>ADJ-S\",,,,,,,,,\"调整范围16～128,工厂调整用,每步0.1毫米\"
,,,\"DADF流动扫描CCD读取位置的调整\",,,,,,,,,\"COPIER>ADJUST>ADJ-XY>STRD-POS\",,,,,,,,,\"调整范围0～60\",,,,\"每步0.1毫米\"
,,\"激光主扫描速度(横向倍率)调整\",,,,,,,,,,\"COPIER>ADJUST>MISC>FRAME-X\",,,,,,,,,\"调整范围-50～ 50,每步1%\"
,,\"副扫描方向扫描速度(纵向倍率)调整\",,,,,,,,,,\"COPIER>ADJUST>MISC>FRAME-Y\",,,,,,,,,\"调整范围-50～ 50,每步1%\"
,,\"主板向DC板送数据时,副扫描方向图像延迟调整\",,,,,,,,,,\"COPIER>ADJUST>MISC>IMG-DLY\",,,,,,,,,\"调整范围-20～ 20,每步0.1毫米\"
,,\"\\\"漏电继电器开关\\\"的检查:\",,,,,,,,\"按\\\"漏电继电器开关\\\"的检查按钮,\\\"漏电继电器开关\\\"跳到开关OFF的位置并将电源切断,\"
,,,,,,,,,,\"如果按检查按钮后,\\\"漏电继电器开关\\\"动作不正常,要更换\\\"漏电继电器开关\\\"后再进行检测\"
,,\"主电源开关,操作面板电源开关ON时时序:\"
,,,\"主电源开关SW1接通复印机AC电源,操作面板电源开关ON时时序:\"
,,,\"加热器开关SW2,接通镜头,扫描反光镜,纸盒加热器的AC电源\"
,,,\"门开关SW3,第1,2组接点接通定影加热器;选购件辅助电源板的AC电源;第3组接点检测门打开/关闭状态,接通主电机.定影电机,复合电源板的24VU1 SW电源\"
,,\"机器启动时序\",,,,,,\"主电源开关ON后主控制板的CPU首先执行辅助ROM中的自诊断程序,检查SDRAM和硬盘 的状态,如果检测到自诊断异常显示\"
,,,,,,,,,\"E601-0000\",,\"硬盘驱动;主控制板\",,,,,\"主控制板与硬盘驱动器图像传输中,主控制板检测到控制信息异常\"
,,,,,,,,,\"E601-0001\",,\"硬盘驱动;主控制板\",,,,,\"主控制板与DC控制板图像传输中,DC控制板检测到控制信息异常\"
,,,,,,,,,\"E602-0001\",,\"硬盘驱动;主控制板\",,,,,\"从BOOT ROM 启动硬盘时检测到硬盘安装异常\"
,,,,,,,,,\"E602-0002\",,\"硬盘驱动;主控制板\",,,,,\"从BOOT ROM 启动硬盘时检测到硬盘读出数据异常\"
,,,,,,,,\"如果自诊断正常,辅助ROM中的辅助程序将系统软件从硬盘中读出并写入SDRAM中系统程序区,此后SDRAM中的系统软件启动,\"
,,,,,,,,\"进行各部分的初始化初,始化完成后显示正常操作画面;复印键的LED灯由红变绿\"
,,\"显示环境传感器检测到的机内温度\",,,,,,,,,,,\"COPIER>DISPLAY>ANALOG>TMPE\",,,,,,,,,,\"单位℃\"
,,\"显示环境传感器检测到的机内相对湿度\",,,,,,,,,,,\"COPIER>DISPLAY>ANALOG>HUM\",,,,,,,,,,\"单位%RH\"
,,\"机内湿度绝对值\",,,,,,,,,,,\"COPIER>DISPLAY>ANALOG>ABS-HUM\",,,,,,,,,,\"单位g\"
,,\"显示OPC鼓周围温度\",,,,,,,,,,,\"COPIER>DISPLAY>ANALOG>DR-TMPE\",,,,,,,,,,\"单位℃\"
,,\"显示主热敏电阻M-TH1检测到定影薄膜中间的温度\",,,,,,,,,,,\"COPIER>DISPLAY>ANALOG>FIX-C\",,,,,,,,,,\"单位℃ \"
,,\"显示副热敏电阻S-TH2检测到定影薄膜边缘的温度\",,,,,,,,,,,\"COPIER>DISPLAY>ANALOG>FIX-E\",,,,,,,,,,\"单位℃\"
,,\"CANON 佳能 iR5000/iR6000 数码复印机读出(扫描)部分维修/调整\"
,,\"进入维修程序模式法:\",,,,,,\"按面板操作部的用户方式(星号\\\"*\\\")键→同时按住数字键\\\"2\\\"和\\\"8\\\"→再按面板操作部的用户方式(星号\\\"*\\\")键\"
,,\"更换读出控制板后执行\",,,,,,\"1,将旧读出控制电路板上的EEPROM取下装到新的读出控制电路板上\"
,,,,,,,,\"2,检查COPIER>ADJUST>AE>的全部项目; COPIER>ADJUST>ADJ-XY>和COPIER>ADJUST>CCD>的全部项目,\"
,,,,,,,,,\"如果与维修模式的值不相同,将新板上的数据登记到维修标签记录卡上\"
,,\"电源ON时扫描时序\",,,,,,\"扫描灯架原位传感器PS400检测到扫描灯架在原位后开始前进扫描动作,然后再返回到原位,曝光灯点亮1秒后进行光补偿(增益调整);\"
,,,,,,,,\"OFF一定间隔后再次ON,100秒后进行光补偿(CCD原稿尺寸检测用临界电平调整),完成扫描准备(SREADY)动作\"
,,\"原稿曝光系统\"
,,\"原稿尺寸检测:\",,,,,,\"1,原稿台读取模式,副扫描方向的原稿尺寸由原稿长度传感器SD1;主扫描方向的原稿尺寸由CCD上的原稿尺寸检测位置的4个检测点\"
,,,,,,,,\"2,ADF的流动读取模式,由ADF的原稿尺寸检测传感器完成\"
,,\"原稿尺寸检测时序\",,,,,\"原稿台盖板打开工作模式时\"
,,,,,,,,\"1,原稿台打开,第1反光镜灯架从待机时的扫描原位传感器PS400位置前进到CCD上设定的4个原稿尺寸检测位置;\"
,,,,,,,,,\"原稿扫描曝光(氙灯)OFF,进行CCD外光检测\"
,,,,,,,,\"2,放置原稿后CCD上的4个原稿检测点如果有的检测点检测到外光,该位置被判定未被原稿盖住表示无原稿\"
,,,,,,,,\"3,按复印键后曝光灯点亮,检测主扫描方向上CCD的原稿原稿尺寸检测点的输出电平;副扫描方向的原稿尺寸由原稿长度传感器SD1检测,\"
,,,,,,,,,\"组合后确定出原稿尺寸\"
,,,,,,,\"原稿台盖板关闭工作模式时\"
,,,,,,,,\"1,原稿台打开,第1反光镜灯架从待机时的扫描原位传感器PS400位置前进到CCD上设定的4个原稿尺寸检测位置;\"
,,,,,,,,,\"原稿扫描曝光(氙灯)OFF,进行CCD外光检测\"
,,,,,,,,\"2,放置原稿后CCD上的4个原稿检测点如果有的检测点检测到外光,该位置被判定未被原稿盖住表示无原稿\"
,,,,,,,,\"3,原稿台盖板关闭角度传感器PS401检测到低于25度时曝光灯点亮,检测主扫描方向上CCD的原稿原稿尺寸检测点的输出电平;\"
,,,,,,,,\"副扫描方向的原稿尺寸由原稿长度传感器PS43检测,组合后确定出原稿尺寸\"
,,\"原稿曝光动作时序\",,,,,\"书本模式/一页原稿/原稿台盖板(闭)\"
,,,,,,,,\"1,稿台打开,第1反光镜灯架从待机时的扫描原位传感器PS400位置前进到原稿尺寸检测位置;原稿扫描曝光(氙灯)OFF,进行CCD外光检测\"
,,,,,,,,\"2,原稿台盖板关闭,曝光灯点亮检测原稿尺寸;原稿尺寸检测后曝光灯OFF,第1反光镜灯架从\"
,,,,,,,,,\"原稿尺寸检测位置返回到扫描原位传感器PS400位置,进行光补偿\"
,,,,,,,,\"3,按复印键后,第1反光镜灯架从扫描原位传感器PS400位置,向左移动到流动读出的开始位置后再开始原稿扫描\"
,,,,,,,,\"4,原稿图像扫描终了,第1反光镜灯架从停止位置返回到流动读出的开始位置后再回到扫描原位传感器PS400位置\"
,,,,,,,\"书本模式/一页原稿/原稿台盖板(开)\"
,,,,,,,,\"1,稿台打开,第1反光镜灯架从待机时的扫描原位传感器PS400位置前进到原稿尺寸检测位置,;原稿扫描曝光(氙灯)OFF,进行CCD外光检测\"
,,,,,,,,\"2,按复印键曝光灯点亮后,检测原稿尺寸,检测后曝光灯OFF,第1反光镜灯架从原稿尺寸检测位置返回到扫描原位传感器PS400位置,\"
,,,,,,,,\"3,进行光补偿,光补偿后,第1反光镜灯架从扫描原位传感器PS400位置,向左移动到流动读出的开始位置后再开始原稿扫描\"
,,,,,,,,\"4,原稿图像扫描终了,第1反光镜灯架从停止位置返回到流动读出的开始位置后再回到原稿尺寸检测位置\"
,,\"原稿扫描曝光LAMP1(氙灯)\",,,,,,,,\"注:曝光灯亮度不可调整;光强度:40000LX\"
,,\"更换\\\"曝光(氙)灯\\\"执行:\",,,,,,,,\"进入维修程序模式, \",,,,\"1,选择COPIER>FUNCTION>CCD>CCD-ADJ 进行CCD自动调整;\"
,,,,,,,,,,,,,,\"2,选择COPIER>ADJUST>CCD>全部项目 进行CCD调整数据\"
,,\"原稿扫描曝光(氙)灯异常\",,,,,,,,\"E220-0001\",,,,\"曝光(氙)灯用的将 24V电压变换为高频高压的(DC/AC)变换电路的INV-ERR信号在读取电路控制板\"
,,,,,,,,,,,,,,\"的待机时检测到灯ON,复印读取时检测到灯OFF;读取电路板故障\"
,,\"曝光(氙)灯电路,CCD/AP电路异常\",,,,,,,,\"E225-0000\",,,,\"电源开关ON后在CCD放大电路光补偿补正中,未收到规定的曝光灯电平信号\"
,,\"曝光(氙)灯电路,CCD/AP电路异常\",,,,,,,,\"E225-0002\",,,,\"顶端放大补正值与前一张的补正值相比超过规定电平\"
,,\"复印倍率: \",,,,,,,,,,,,\"1,ADF模式: 25～800%(第1反光镜架固定在流动读取位置的曝光玻璃下,原稿由ADF输送)\"
,,,,,,,,,,,,,,\"2,原稿台读取模式: 25～800%\"
,,\"倍率变化:\",,,,,,,,\"主扫描方向\",,,,\"主扫描方向25～800%,由主控制板图像处理的变倍程序软件完成,\"
,,,,,,,,,,\"副扫描方向\",,,,\"副扫描方向50%以上由第1反光镜架的扫描速度或ADF的原稿搬送速度确定\"
,,,,,,,,,,,,,,\"副扫描方向25%～49%和401%～800%由主控制板图像处理的变倍程序软件完成,\"
\" \",,\"原稿扫描电机,扫描原位传感器\",,,,,,,,\"E202-0001\",,,,\"电源开关ON后或按复印键后光学系统前进40毫米,扫描原位传感器PS400未OFF;或扫描电机M3故障\"
,,\"原稿扫描电机,扫描原位传感器\",,,,,,,,\"E202-0002\",,,,\"光学系统返回450毫米,光学系统扫描原位传感器PS400未ON;\"
,,,,,,,,,,,,,,\"注:键盘锁住,不显示E202;可进入维修程序模式,选择COPIER>DISPLAY>ERR 中确定故障码\"
,,\"图象前沿检测信号故障(ADF)\",,,,,,,,\"E204-0001\",,,,\"ADF板或读取板故障,打印过程中未收到ADF来的图象前沿信号;扫描灯架前进时未收到图象前沿信号. \"
,,,,,,,,,,,,,,\"注:键盘锁住,不显示E204;可进入维修程序模式,选择COPIER>DISPLAY>ERR 中确定故障码\"
,\"扫描位置调整\",,,,,,,,,\"ADJ-XY\",,,\"COPIER>ADJUST>ADJ-XY>\"
,,\"副扫描方向图像读取开始位置调整\",,,,,,,,\"COPIER>ADJUST>ADJ-XY>ADJ-X\",,,,,,,,,\"调整范围250～290\",,,,\"每步0.1毫米\",,,\"数据大移向稿台刻度\",,,,,\"标准2.5±1.5毫米\"
,,\"主扫描方向图像读取开始位置调整\",,,,,,,,\"COPIER>ADJUST>ADJ-XY>ADJ-Y\",,,,,,,,,\"调整范围100～400\",,,,\"每步0.1毫米\",,,\"读取开始位置在稿台玻璃左后方,数据大移向前边\"
,,\"光学原位位置调整(HP传感器)\",,,,,,,,\"COPIER>ADJUST>ADJ-XY>ADJ-S\",,,,,,,,,\"调整范围55～70\",,,,\"每步0.1毫米\",,,\"调整值改变后必修将ADF打开再关闭\"
,,\"ADF主扫描方向图像读取开始位置调整\",,,,,,,,\"COPIER>ADJUST>ADJ-XY>ADJ-Y-DF\",,,,,,,,,\"调整范围100～400\",,,,\"每步0.1毫米\"
,,\"用ADF移动扫描时CCD读取位置的调整\",,,,,,,,\"COPIER>ADJUST>ADJ-XY>STRD-POS\",,,,,,,,,\"调整范围0～60\",,,,\"每步0.1毫米\"
,\"图像处理系统\",,,,,,,\"CCD/AP板(CCD驱动;模拟图像处理;A/D变换)注:CCD,600dpi(7450象素);255级灰度;读取控制板(光补偿补正;自动浓度调整)\"
,,\"模拟图像处理\",,,,,,\"由CCD/AP板完成:CCD驱动;模拟图像处理(CCD输出的增益补正,不均匀性补正);CCD输出的A/D变换\"
,,\"CCD输出的增益补正,不均匀性补正\",,,,,,,,\"由于CCD(7450个象素)各象素的光电转换效率不可能相同,要进行CCD输出的模拟图像信号增益补正,;\"
,,,,,,,,,,\"使无入射光时的输出电压为一定值,进行不均匀性补正;注:CCD,600dpi(7450象素);255级灰度(8bit A/D变换)\"
,,\"数字图像处理\",,,,,,\"由读取控制板完成 遮蔽Shading补偿补正,自动浓度调整\"
,,\"遮蔽Shading补偿\",,,,,,\"由于CCD各象素的感光度不均匀;镜头中心与边缘透光率不同;曝光灯中间与边光量不同和老化\"
,,,,,,,,\"遮蔽Shading补偿分:用维修模式确定目标值的遮蔽Shading补偿调整和\"
,,,,,,,,,,,,\" 每次原稿扫描时进行的遮蔽Shading补偿补正;短期光量变动的补正用增益来补正\"
,,\"遮蔽Shading补偿调整\",,,,,,\"测定白纸和标准白板的浓度数据经演算处理并记忆这些参数作为遮蔽Shading补偿的目标值(更换曝光灯或光量变化后用维修模式进行)\"
,,\"遮蔽Shading补偿补正\",,,,,,\"每次原稿扫描时进行,先测定标准白板的数据然后与遮蔽Shading补偿补正的目标值进行比较将其差值作遮蔽Shading补偿补正值来设定\"
,,,,,,,,\"补偿原稿扫描时的各CCD的图像的偏差使图像浓度均匀\"
,,\"端部增益补正(ADF用)\",,,,,,\"ADF进行流动读出时,第1反光镜灯架固定在流动读出位置,为检测光量的变化在流动读出玻璃的后端部安装了\"
,,,,,,,,\"端部增益补正测试板(灰色)读出该测试板反射回来光量,经过计算后作为增益值,使用该数据进行光量变化的补正\"
,,\"标准白纸的浓度数据设定\",,,,,,\"如有底灰降低设定数\",,,,,,,\"COPIER>ADJUST>CCD>PPR\",,,,,,,,\"设定范围0～255\"
,,\"标准白板的浓度数据设定\",,,,,,,,,,,,,\"COPIER>ADJUST>CCD>PLT\",,,,,,,,\"设定范围0～255\"
,,\"CCD输出的增益调整值输入\",,,,,,,,,,,,,\"COPIER>ADJUST>CCD>GAIN-E/O\"
,,\"CCD输出的不均匀性Offset调整值输入\",,,,,,,,,,,,,\"COPIER>ADJUST>CCD>OFST-E/O\"
,,\"遮蔽Shading补偿补正时标准白纸和标准白板的白电平比例数据\",,,,,,,,,,,,,\"COPIER>ADJUST>CCD>SH-RATIO \"
,,\"遮蔽Shading补偿正时的白色程度目标值输入\",,,,,,,,,,,,,\"COPIER>ADJUST>CCD>SH-TRGT\"
,,\"CCD的顶端放大补正开始位置调整值输入\",,,,,,,,,,,,,\"COPIER>ADJUST>CCD>EGGN-ST\"
,,\"CCD的顶端放大补正结束位置调整值输入\",,,,,,,,,,,,,\"COPIER>ADJUST>CCD>EGGN-END\"
,,\"实时AE模式的文字浓度调整\",,,,,,,,,,,,,\"COPIER>ADJUST>AE>AE-TBL\",,,,,,,\"调整范围1～9,缺省值5,数据大文字浓度加深\"
,,,,,,,,,,,,,,,\"对报纸类等底色浓的原稿为了使复印件不再出现原稿的底色,\"
,,,,,,,,,,,,,,,\"本调整在自动浓度模式或文字模式有效,ABC回路进行数据处理\"
,,\"CCD光补偿自动补正的自动调整:\",,,,,,,\"COPIER>FUNCTION>CCD>CCD-ADJ\"
,,,,,,,,,,,,,,,\"1,稿台上放10张标准白纸\"
,,,,,,,,,,,,,,,\"2,选择COPIER>FUNCTION>CCD>CCD-ADJ \"
,,,,,,,,,,,,,,,\"3,CCD-ADJ,显示反转后按OK键后进行自动调整\"
,,,,,,,,,,,,,,,\"4,COPIER>ADJUST>CCD>的整个项目已更新,要在维修标签中进行登记\"
,,\"CCD 遮蔽(Shading)补偿位置调整:\",,,,,,,\"COPIER>FUNCTION>CCD>SHDG-POS\",,,,,,,,,\"遮蔽(Shading)补偿的标准白板上的位置自动调整的数据,调整范围240～ 320\"
,,\"CCD 遮蔽(Shading)补偿位置设定:\",,,,,,,\"COPIER>FUNCTION>CCD>SH-PS-SET\",,,,,,,,,\"遮蔽(Shading)补偿的标准白板上的位置自动调整的数据\"
,,,,,,,,,,,,,,,\"更换稿台玻璃(标准白色板)以后或中间色调中有明显的白色条时要执行该模式\"
,,,,,,,,,,,,,,,\"执行该模式前要进行COPIER>FUNCTION>CCD>CCD-ADJ 调整\"
,,,,,,,,,,,,,,,\"1,清洁稿台玻璃\"
,,,,,,,,,,,,,,,\"2,选择COPIER>FUNCTION>CCD>SH-PS-SET,按OK键 \"
,,,,,,,,,,,,,,,\"3,按OK执行自动CCD 遮蔽(Shading)补偿位置设定调整,调整后自动停止.\"
,,\"CCD的端部放大补正的自动调整\",,,,,,,\"COPIER>FUNCTION>CCD>EGGN-POS\",,,,,,,,,\"(仅使用RADF进行流动读出时有效)\"
,,,,,,,,,,,,,,,\"1,打开ADF,\"
,,,,,,,,,,,,,,,\"2,选择该项目按OK键,\"
,,,,,,,,,,,,,,,\"3,自动调整,(大约分钟)调整后自动停止\"
,,,,,,,,,,,,,,,\"(如果显示NG检查:ADF是否打开;移动读出用扫描玻璃安装是否正确;\"
,,,,,,,,,,,,,,,\"玻璃顶端(后面)的灰色放大补正板是否有问题;原稿曝光灯点亮是否正确)\"
,,,,,,,,,,,,,,,\"由于COPIER>ADJUST>CCD>EGGN-ST和EGGN-END的项目已更新,要在维修标签中进行记录\"
,,\"图像清晰度电平设定\",,,,,,,\"COPIER>OPTION>BODY>SHARP\",,,,,,,,\"设定范围:1～5 ;缺省值=3,数值大清晰度高(焦距增大)\"
,\"更换CCD/AP单元后要执行:\"
,,\"1.CCD光补偿自动补正的自动调整: COPIER>FUNCTION>CCD>CCD-ADJ\"
,,,,,\"1,稿台上放10张标准白纸\"
,,,,,\"2,选择COPIER>FUNCTION>CCD>CCD-ADJ \"
,,,,,\"3,CCD-ADJ,显示反转后按OK键后进行自动调整\"
,,,,,\"4,COPIER>ADJUST>CCD>的整个项目已更新,要在维修标签中进行登记\"
,,\"2.CCD的端部放大补正的自动调整: COPIER>FUNCTION>CCD>EGGN-POS\",,,,,,,,,,,,,,,,,\"(仅使用ADF进行流动读出时有效)\"
,,,,,\"1,打开ADF,\"
,,,,,\"2,选择该项目按OK键,\"
,,,,,\"3,自动调整,\"
,,,,,\"4,调整后自动停止显示OK/NG,\"
,,,,,\"(如果显示NG检查:ADF是否打开;移动读出用扫描玻璃安装是否正确;玻璃顶端(后面)的灰色放大补正板是否有问题;原稿曝光灯点亮是否正确)\"
,,,,,\"5,由于COPIER>ADJUST>CCD>EGGN-ST和EGGN-END的项目已更新,要在维修标签中进行记录\"
,,\"3.CCD调整数据: COPIER>ADJUST>CCD>的全部\",,,,,,,,,,,,,,,\"进行COPIER>FUNCTION>CCD>CCD-ADJ操作后,图像有问题时,输入维修标签上的值\"
,,,,,\"电信号补偿正时的白色程度目标值输入\",,,,,,,,,,,,\"COPIER>ADJUST>CCD>SH-TRGT\"
,,,,,\"电信号补偿正时的标准白色纸与标准白板之比率数据值\",,,,,,,,,,,,\"COPIER>ADJUST>CCD>SH-RATIO\"
,,,,,\"CCD的端部放大补正开始位置调整值输入\",,,,,,,,,,,,\"COPIER>ADJUST>CCD>EGGN-ST\"
,,,,,\"CCD的端部放大补正结束位置调整值输入\",,,,,,,,,,,,\"COPIER>ADJUST>CCD>EGGN-END\"
,,\"CCD读取位置调整\",,,,,,,,\"ADJ-XY\"
,,\"主扫描方向图像读取开始位置调整\",,,,,,,,\"COPIER>ADJUST>ADJ-XY>ADJ-Y\",,,,,,,,,\"调整范围100～400\",,,,\"每步0.1毫米\",,,\"数据大移向前边\"
,,\"副扫描方向图像读取开始位置调整\",,,,,,,,\"COPIER>ADJUST>ADJ-XY>ADJ-X\",,,,,,,,,\"调整范围250～290\",,,,\"每步0.1毫米\",,,\"数据大移向稿台刻度\",,,,,\"标准2.5±1.5毫米\"
,,\"光学原位(白板读取位置)调整(HP传感器)\",,,,,,,,\"COPIER>ADJUST>ADJ-XY>ADJ-S\",,,,,,,,,\"调整范围55～70\",,,,\"每步0.1毫米\",,,\"调整值改变后必修将ADF打开再关闭\"
,,\"ADF主扫描方向图像读取开始位置调整\",,,,,,,,\"COPIER>ADJUST>ADJ-XY>ADJ-Y-DF\",,,,,,,,,\"调整范围100～400\",,,,\"每步0.1毫米\"
,,\"用ADF移动扫描时CCD读取位置的调整\",,,,,,,,\"COPIER>ADJUST>ADJ-XY>STRD-POS\",,,,,,,,,\"调整范围30～60\",,,,\"每步0.1毫米\"
,,\"电信号补偿正时的白色程度目标值输入\",,,,,,,,\"COPIER>ADJUST>CCD>SH-TRGT\"
,,\"标准白纸和标准白板的白电平比例数据\",,,,,,,,\"COPIER>ADJUST>CCD>SH-RATIO\",,,,,,,,,\"CCD光补偿正时,标准白纸和标准白板的白电平比例数据\"
,,\"CANON 佳能 iR5000/iR6000 数码复印机打印部分维修/调整\"
,,\"OPC感光鼓\",,,,,,,,,\"更换OPC感光鼓后要执行鼓电阻检测控制(APVC),COPIER>FUNCTION>DPC>D-GAMMA\"
,,\"1,预曝光使鼓清洁消电\",,,,,,,,,\"OPC感光鼓消电用的预曝光灯LAMP2:为8个保险丝式灯,PEXP/\"
,,\"2,一次充电辊充电电流\",,,,,,,,,\"一次充电辊DC电压:大约-750V(23度时)到-850V;AC电压1800Hz:大约2000到2300V,\"
,,,,,,,,,,,\"一次充电电流随着工作环境(温度,湿度)充电辊老化,OPC鼓磨损/老化等因素鼓的电阻发生变化,为了保持复印质量稳定,\"
,,,,,,,,,,,\"该机采用根据每累积复印张数达500张时的鼓后旋转期检测一次鼓电阻发生的变化,来修改一次充电辊充电电流,\"
,,,,,,,,,,,\"或当强行执行鼓电阻检测控制(APVC)\\\"COPIER>FUNCTION>DPC>D-GAMMA\\\",当前输出电平被测试和校正\"
,,,,,,,,,,,\" 1.主电源开关打开时,基准电压加到一次充电辊,当前测试的输出电平反馈到PW-CPU\"
,,,,,,,,,,,\" 2,用PW-CPU检测到的反馈电压电平控制一次充电辊的充电电压\"
,,,,,,,,,,,\"OPC鼓周围温度检测传感器U701,用于校整一次充电辊DC电压:大约-750V(23度时)到-850V\"
,,,,\"环境传感器ON/OFF\",,,,,,,\"COPIER>OPTION>BODY>HUM-SW\",,,,,,,,\"0:环境传感器自动控制;1:固定模式,高湿度;2:固定模式,中湿度;3固定模式,低湿度\"
,,,,,,,,,,,\" 环境传感器S3检测到的机内相对湿度,校整一次充电辊AC电压,以35%湿度为基准在10000张前不进行湿度校整2300微安.\"
,,,,,,,,,,,\" 10000张以后开始进行湿度校整,小于35%湿度为2150微安;大于35%湿度为2100微安\"
,,,,\"一次充电辊的清洁\",,,,,,,\"在执行用户模式的调整/清洁,一次充电辊清洁电磁铁动作可使一次充电辊清洁垫压在一次充电辊上并前后移地\"
,,\"显示当前鼓电阻检测控制的电流值\",,,,,,,,,\"COPIER>DISPLAY>HV-STS>PRIMARY\",,,,,,,,,\"一次充电电流小于353微安,好鼓;353～485微安鼓尚可使用;大于485微安换鼓\"
,,\"图像区域一次充电辊的负DC电压调整\",,,,,,,,,\"COPIER>ADJUST>HV-PRI>P-DC\",,,,,,,,,\"调整范围0～255\",,,,,\"DC-500～-850\"
,,\"图像区域一次充电辊的AC电压调整\",,,,,,,,,\"COPIER>ADJUST>HV-PRI>P-AC\",,,,,,,,,\"调整范围0～255\",,,,,\"AC2.0～2.3KV;Vf=1.8KHz\"
,,\"鼓电阻检测控制(APVC)增益调整值的调整\",,,,,,,,,\"COPIER>ADJUST>HV-PRI>AGS-GANE\",,,,,,,,,\"调整范围0～255,更换复合电源板时,把复合电源板上的标签值输入\"
,,\"鼓电阻检测控制(APVC)ofst调整值的输入\",,,,,,,,,\"COPIER>ADJUST>HV-PRI>AGS-OFST\",,,,,,,,,\"调整范围0～255,更换复合电源板时,把复合电源板上的标签值输入\"
,,\"一次充电辊的负DC电压ofst调整\",,,,,,,,,\"COPIER>ADJUST>HV-PRI>OFST1-DC\",,,,,,,,,\"调整范围0～255\"
,,\"一次充电辊的AC电压ofst调整\",,,,,,,,,\"COPIER>ADJUST>HV-PRI>OFST1-AC\",,,,,,,,,\"调整范围0～255\"
,,\"图像区域的一次充电辊的AC2电压调整\",,,,,,,,,\"COPIER>ADJUST>HV-PRI>P-AC2\",,,,,,,,,\"调整范围0～255\"
,,\"图像区域的一次充电辊的AC3电压调整\",,,,,,,,,\"COPIER>ADJUST>HV-PRI>P-AC3\",,,,,,,,,\"调整范围0～255\"
,,\"强行执行鼓电阻检测控制(APVC)\",,,,,,,,,\"COPIER>FUNCTION>DPC>D-GAMMA\",,,,,,,,,\"更换鼓后或使用旧鼓或复印浓度调整无结果时用\"
,,,,,,,,,,,,,,,,,,,,\"缺省值0:正常模式;1:执行鼓电阻测量(APVC)控制,选择D-GAMMA显示反转后\"
,,,,,,,,,,,,,,,,,,,,\"按OK键打印出1张黑色样板,在COPIER>DISPLAY>HV-STS>PRIMARYK中\"
,,,,,,,,,,,,,,,,,,,,\"可以显示出当前鼓电阻测量控制(APVC)的一次鼓充电辊电流结果\"
,,\"3,激光扫描曝光:\",,,,,,,,,\"可视激光(780nm)1个光束,6个光反射面菱镜,激光扫描器的激光投向OPC感光鼓有图象信号的黑区\"
,,,,\"激光读出同步\",,,,\"主扫描方向:\",,,\"由激光原位信号BD确定同步时间,双面时,由横向对位传感器PS11(Y-REG-PD检测结果再由BD信号确定激光读出的同步;\"
,,,,,,,,,,,\"手送纸时由对位传感器PS29检测到复印纸前沿开始激光读出的同步\"
,,,,,,,,\"副扫描方向:\",,,\"由对位辊前的激光读出图像前沿传感器PS12检测到复印纸前沿启动激光读出开始的同步;\"
\" \",,\"4,显影偏压(AC 负DC)\",,,,,,,,,\"干式单组分磁性墨粉(墨粉带负极性电荷) 跳跃显影,磁辊(φ20)\"
,,,,\"显示显影DC偏压(单位V)\",,,,,,,\"COPIER>DISPLAY>HV-STS>BIAS\",,,,,,,,,\"DC偏压:0～-650V\"
,,,,\"图像区域显影偏压DC输出的调整\",,,,,,,\"COPIER>ADJUST>DEVELOP>DE-BC\",,,,,,,,,\"DC偏压:0～-650V\",,,,\"调整范围:0图像浓～255图像淡\"
,,,,,,,,,,,,,,,,,,,,\"AC偏压:Vpp=810V,Vf=1.8KHz\"
,,,,\"显影偏压DC输出值的调整OFST\",,,,,,,\"COPIER>ADJUST>DEVELOP>DE-OFST\",,,,,,,,,\"DC输出值的调整\",,,,\"调整范围:0图像浓～255图像淡(在缺省值±30内调整)\"
,,\"5,转印辊充电高压(正DC)\"
,,,,\"基准电压\",,,,,,,\"转印辊电阻检测控制(ATVC),主电源开关打开时的鼓预旋转期间或根据每累积复印张数达1000张时的鼓后旋转期间或\"
,,,,,,,,,,,\"用户模式执行调整/清洁期间,检测转印辊电阻发生的变化,把基准电压加到转印辊,当前转印辊的输出电平被测试和校正,\"
,,,,,,,,,,,\"该输出电平并反馈到PW-CPU,PW-CPU用检测到的反馈电压电平控制转印辊充电高压的输出\"
,,,,\"负转印辊清洁偏压\",,,,,,,\"按复印键后的预旋转期间或复印结束的后旋转期间;卡纸排除或出错复位后的预旋转期间;或用户模式执行调整/清洁期间\"
,,,,,,,,,,,\" 在转印辊上加上负转印辊清洁偏压将粘在转印辊的墨粉返回到OPC鼓上\"
,,,,\"连续复印页到页间偏压\",,,,,,,\"连续复印页到页间的无图像区转印辊充电电压被降低以防止墨粉粘在转印辊上\"
,,,,\"负转印导板偏压\",,,,,,,\"在转印导板上加上负600V 防止带负极性电荷的墨粉粘在转印导板上\"
,,,,\"显示当前转印辊充电的电流(微安)\",,,,,,,\"COPIER>DISPLAY>HV-STS>TR\",,,,,,,,,,\"0:转印电压恒压模式;1:转印电压恒压模式(中等);\"
,,,,,,,,,,,\"COPIER>DISPLAY>HV-STS>TR-V\",,,,,,,,,,\"2:转印电压恒压模式(大);3:转印电压恒压模式(小)\"
,,,,\"显示转印充电辊表面电位控制\",,,,,,,,,,,,,,,,,\"1500～6000V:转印充电辊系统正常,大于6001V:转印充电辊卡住;\"
,,,,,,,,,,,,,,,,,,,,,\"小于1499V:转印充电辊漏或转印充电辊故障\"
,,,,\"转印辊正高压电流的调整\",,,,,,,\"COPIER>ADJUST>HV-TR>TR-N1\",,,,,,,,\"第1面\",,\"调整范围0～10,更换DC控制板时,输入维修标签上的值\",,,\"单位:微安\"
,,,,\"转印辊正高压电流的调整\",,,,,,,\"COPIER>ADJUST>HV-TR>TR-N2\",,,,,,,,\"第2面\",,\"调整范围0～10,更换DC控制板时,输入维修标签上的值\"
,,,,\"转印辊正高压OFST的调整\",,,,,,,\"COPIER>ADJUST>HV-TR>TR-OFST\",,,,,,,,,,\"调整范围0～255,更换DC控制板时,输入维修标签上的值\"
,,,,\"转印辊正高压电流的调整\",,,,,,,\"COPIER>ADJUST>HV-TR>TR-SPP\",,,,,,,,\"厚纸\",,\"调整范围0～10,更换DC控制板时,输入维修标签上的值\"
,,,,\"大尺寸纸时转印辊电流输出控制\",,,,,,,\"COPIER>OPTION>BODY>TRANS-SW\",,,,,,,,,,\"0:正常(自动模式);\"
,,,,,,,,,,,,,,,,,,,,,\"1:恒定电压控制(手动模式),\",,,,,,\"对手进纸盘选择厚纸模式时有效\"
,,,,,,,,,,,,,,,,,,,,,,\"选择1后还要在COPIER>ADJUST>HV-TR>TR-N1中设定\"
,,\"6,分离放电针高压(负DC)\",,,,,,,,,\"分离放电针DC定电压控制,由环境传感器和纸类型控制\"
,,,,,,,,,,,\"在低湿度环境,使用薄纸或双面的第2面分页器分离不良,分离放电针高压增加到-2.3KV到-3.0KV之间\"
,,\"7,定影\",,\"定影热辊采用定影薄膜,定影器由电机M4驱动;主/副定影加热器 H1/H2 (637W);热敏开关TP1 动作温度240±度;\"
,,,,\"定影温度设修改选择\",,,,,,,\"COPIER>OPTION>BODY>FIX-TEMP\",,,,,,,,\"0:禁止(缺省值)\"
,,,,,,,,,,,,,,,,,,,\"1:保持定影温度恒定在目标温度-10度\"
,,,,,,,,,,,,,,,,,,,\"2:保持定影温度恒定在目标温度-6度\"
,,,,,,,,,,,,,,,,,,,\"3:保持定影温度恒定在目标温度-3度\"
,,,,,,,,,,,,,,,,,,,\"4:保持定影温度恒定在目标温度 3度\"
,,,,,,,,,,,,,,,,,,,\"5:保持定影温度恒定在目标温度 6度\"
,,,,,,,,,,,,,,,,,,,\"6:保持定影温度恒定在目标温度 10度\"
,,,,,,,,,,,,,,,,,,,\"7:保持定影温度恒定在目标温度 15度\"
,,,,\"显示主定影薄膜中间的温度\",,,,,,,\"COPIER>DISPLAY>ANALOG>FIX-C\",,,,,,,,\"显示主热敏电阻M-TH1检测到定影薄膜中间的温度,单位℃ \"
,,,,\"显示副定影薄膜边缘的温度\",,,,,,,\"COPIER>DISPLAY>ANALOG>FIX-E\",,,,,,,,\"显示副热敏电阻S-TH2检测到定影薄膜边缘的温度,单位℃ \"
,,,,\"厚纸定影辊薄膜速度调整\",,,,,,,\"COPIER>ADJUST>FIXING>FX-FL-TH\",,,,,,,,\"选择该项目显示反转后按OK键,调整范围-3～ 3,缺省值=0\"
,,,,\"普通纸定影辊薄膜速度调整\",,,,,,,\"COPIER>ADJUST>FIXING>FX-FL-SP\",,,,,,,,\"选择该项目显示反转后按OK键,调整范围-3～ 3,缺省值=0\"
\"iR2200,iR2800,iR3300 数码复印机维修程序\"
\"制作: WGF\"
\"共页 ,第页\"
,,,,,\"CANON 佳能 iR2200/iR2800/iR3300 数码复印机故障码\"
,\"进入维修程序模式法\",,,,,,\"按面板操作部的用户方式(星号\\\"*\\\")键→同时按住数字键\\\"2\\\"和\\\"8\\\"→再按面板操作部的用户方式(星号\\\"*\\\")键\"
,\"打印维修程序模式报表\",,,,,,\"进入维修程序模式,选择COPIER>FUNCTION>MISC-P>P-PRINT\\\"[打印维修模式(ADJUST,OPTION,COUNTER)的内容\\\"],\"
,,,,,,,\"P-PRINT显示反转后按OK键,可将维修模式当前值的清单一次全部打印出来.\"
,,,\"故障码表\",,,,,,,,,,,,\"6-2T\"
,,\"复印机定影部分故障E00×\"
,\"E000\",,\"定影升温故障\",,,,,\"电源开关ON后1秒,主(中间)热敏电阻M-TH1检测到定影热辊薄膜的温度低于30度,ON后2秒,温度低于70度\",,,,,,,,,,,\"J426(白线,大约1000～1400K欧母)\"
,,,,,,,,\"主热敏电阻M-TH1开路;定影薄膜加热器637W开路;热敏开关TP1开路;SSR故障;DC控制板故障\"
,\"E001\",\"0000\",,,,,,\"主热敏电阻M-TH1检测到定影热辊薄膜的温度超过250度;主热敏电阻M-TH1短路\"
,\"E001\",\"0001\",\"热敏电阻硬件电路检测到定影超温\",,,,,\"主/副热敏电阻硬件电路检测到定薄膜的温度过高;主(中间)/副(边缘)热敏电阻M-TH1/S-TH2短路\"
,,,,,,,,\"进入维修程序模式,选择COPIER>DISPLAY>ANALOG>FIX-C 或FIX-E\"
,,,,,,,,\"当显示反转后按OK键盘,显示定影主热敏电阻M-TH1检测到定影薄膜的中间温度FIX-C (250度),\"
,,,,,,,,\"副热敏电阻S-TH2检测到定影薄膜的边缘温度FIX-E(310度)\"
,\"E001\",\"0002\",\"定影超温\",,,,,\"副热敏电阻S-TH2检测到定影温度超过295度;主热敏电阻TH1短路\",,,,,,,,,,,\"J426(黑线,大约40～50K欧母)\"
,\"E002\",\"0000\",\"予热异常\",,,,,\"定影温度1秒后超过100度,但未达到115度;定影温度1秒后超过140度,但未达到150度;定影温度1秒后超过160度,但未达到165度\"
,\"E003\",\"0000\",\"予热异常\",,,,,\"复印纸通过定影热辊薄膜后,薄膜温度降低到140度\"
,\"E007\",\"0000\",\"定影热辊薄膜转动检测信号故障\",,,,,\"主热敏电阻M-TH1检测到定影热辊薄膜的温度达到100度后,定影电机转动6秒后,\"
,,,,,,,,\"定影热辊薄膜转动检测传感器PS26未检测到定影热辊薄膜转动信号FILM-ROT-D(100毫秒ON,440毫秒OFF)\"
,,\"电机故障\",,,,,,,,,,,,,,\"6-9T\"
,\"E010\",,\"主电机M1故障\",,,,,\"电机启动信号MM-ON输出后1.3秒未接收到电机转速正常(电机锁定信号J318-A10,MM-LOCK=1)信号\"
,\"E014\",,\"定影电机M4故障\",,,,,\"电机启动信号FSRM-ON输出后1.3秒未接收到电机转速正常(电机锁定信号J312-B4,FSRM-LOCK=1)信号\"
,\"E019\",,\"废墨粉瓶满\",,,,,\"废墨粉瓶粉满传感器(S2)检测到粉满打印100次,显示废墨粉瓶粉满警告信息,再打印200次还检测到废墨粉瓶粉满,显示\\\"E019\\\"\"
,,\"选购件计数器故障\",,,,,\" \",,,,,\" \",,,,\"6-10T\"
,\"E032\",\"0001\",\"DA选购件复印控制计数器\",,,,\" \",\"复印数据控制板或NE控制板未连接或出故障\",,,,,,,,\" \"
,\"E051\",\"0000\",\"驱动横向对位传感器步进电机M3\",,,,,\"横向对位传感器步进电机M3驱动后,横向对位传感器PS11,未检测到Y-REG-PD原位信号\"
,,\"复合电源板(一次,转印,显影偏压)出错\",,,,,,,,,,,,,,\"6-12T\"
,\"E064\",,\"复合电源板(一次,转印,显影偏压)出错\",,,,,\"复合电源板,一次,转印,显影偏压,漏电或电流过小出错\"
,,\"激光BD信号故障;激光驱动电路故障\",,,,,,,,,,,,,,\"6-13T\"
,\"E100\",\"0001\",\"激光原位信号(BD)故障\",,,,,\"激光驱动信号输出5毫秒后,在10毫秒内BD信号未检测到达10次以上\"
,\"E100\",\"0002\",\"激光原位信号(BD)故障\",,,,,\"激光发射中BD信号周期超过规定范围的状态连续出现达20次以上\"
,\"E100\",\"0003\",\"水平同步信号LSYNC出错\",,,,,\"激光发射中,水平同步信号LSYNC周期超过规定范围的状态连续出现达20次以上\"
\" \",\"E110\",\"0000\",\"激光扫描电机M10异常\",,,,,\"激光扫描电机ON后15秒,未收到LMRDY/信号(未达到规定的速度)\"
,,,\"原稿光学扫描,读取电路\",,,,,\" \",\" \",,,\" \",,,,\"6-15T\",,\" \"
\" \",\"E202\",\"0001\",\"原稿扫描电机,扫描原位传感器\",,,,,\"电源开关ON后或按复印键后光学系统前进40毫米,光学系统扫描原位传感器PS400未OFF;或扫描电机M3故障\"
,,\"0002\",\"原稿扫描电机,扫描原位传感器\",,,,,\"光学系统返回450毫米,光学系统扫描原位传感器PS400未ON;\"
,,,,,,,,\"注:键盘锁住,不显示E202;可进入维修程序模式,选择COPIER>DISPLAY>ERR 中确定故障码\"
,\"E204\",\"0001\",\"图象前沿检测信号故障(ADF)\",,,,,\"ADF控制板或读取控制板故障,打印过程中未收到ADF来的图象前沿信号;扫描灯架前进时未收到图象前沿信号. \"
,,,,,,,,\"注:键盘锁住,不显示E204;可进入维修程序模式,选择COPIER>DISPLAY>ERR 中确定故障码\"
,\"E220\",\"0001\",\"原稿扫描曝光(氙)灯异常\",,,,,\"曝光(氙)灯 24V变换到高频高压的(DC/AC)变换电路的INV-ERR信号在读取电路控制板的待机时检测到灯ON,\"
,,,,,,,,\"或复印读取时检测到灯OFF;读取电路板故障\"
,\"E225\",\"0000\",\"曝光(氙)灯电路,CCD/AP电路\",,,,,\"电源开关ON后在CCD放大电路光补偿补正中,未收到规定的曝光灯电平信号\"
,\"E225\",\"0002\",\"曝光(氙)灯电路,CCD/AP电路\",,,,,\"顶端放大补正值与前一张的补正值相比超过规定电平\",,,,,,,,,,\" \"
,,,\"通信不良\",,,,,,,,,,,,,\"6-16T\"
,\"E240\",\"0000\",\"DC控制板与主控制板通信不良\",,,,,\"DC控制板CPU与主控制板CPU通信不良\",,,,,,\" \",,,\" \"
,\"E243\",\"0000\",\"主控制板与操作面板通信不良\",,,,,\"主控制板CPU与操作面板CPU通信不良\"
,,,\"EEPROM故障\",,,,,,,,,,,,,\"6-17T\"
,\"E248\",\"0001\",\"读取电路板或EEPROM故障\",,,,,\"电源开关ON后读出的EEPROM内的ID码与ROM中的ID码不同\"
,\"E248\",\"0002\",\"读取电路板或EEPROM故障\",,,,,\"向EEPROM写入数据时,写入的数据与读出的数据不同\"
,\"E248\",\"0003\",\"读取电路板或EEPROM故障\",,,,,\"向EEPROM写入数据时,EEPROM内的ID码与ROM中的ID码不同\"
,,,,,,,,\"检查读取电路板上的EEPROM安装是否正确\"
,,,,,,,,\"进入维修程序模式,选择COPIER>FUNCTION>CLEAR>R-CON 选择R-CON,当显示反转后按OK键;OFF/ON主电源开关\"
,,,,,,,,\"清除读取电路板的RAM后重新输入维修模式中的数据,如果工作仍旧不正常更换EEPROM或DC控制板\"
,,,\"CCD/AP电路;读取电路板\",,,,,,,,,,,,,\"6-19T\"
,\"E302\",\"0001\",\"CCD/AP电路;读取电路板\",,,,,\"进行遮蔽Shading信号补偿时,经过1秒读取电路板的遮蔽Shading信号信号补偿处理未能结束\"
,\"E302\",\"0002\",\"CCD/AP电路;读取电路板\",,,,,\"在移动扫描时,经过10秒读取玻璃顶端的灰白色边缘补偿板时,附加处理未能结束\"
,\"E315\",,\"图像数据处理出错\",,,,,\"图像数据出错,图像的编码/解码出错,主控制板中的图像数据处理部分出错\"
,,,\"硬盘;主控制板\",,,,,,,,,,,,,\"6-21T\"
,\"E601\",\"0000\",\"硬盘驱动;主控制板\",,,,,\"主控制板与硬盘驱动器图像传输中,主控制板检测到控制信息异常\"
,\"E601\",\"0001\",\"硬盘驱动;主控制板\",,,,,\"主控制板与DC控制板图像传输中,DC控制板检测到控制信息异常\"
,\"E602\",\"0001\",\"硬盘驱动;主控制板\",,,,,\"从BOOT ROM 启动硬盘时检测到硬盘数额读出错误\"
,\"E602\",\"0002\",\"硬盘驱动;主控制板\",,,,,\"从BOOT ROM 启动硬盘时检测到硬盘读出数据异常\"
,\"E604\",\"0000\",\"图像存储器检测到出错\",,,,,\"硬盘失效;主控制板失效\"
,\"E605\",\"0001\",\"图像存储器的电池坏\"
,\"E606\",\"0001\",\"硬盘错误\",,,,,\"从BOOT ROM 启动硬盘时检测到硬盘安装错误\"
,,,\"打印板/传真板通信不良\",,,,,,,,,,,,,\"6-23T\"
,\"E674\",\"0001\",\"传真板与主控制板通信不良\",,,,,\"传真板与主控制板通信不良\"
,\"E677\",\"0001\",\"各种打印板与主控制板通信不良\",,,,,\"各种打印板,卡与主控制板通信不良\"
,,,\"不能初始化\",,,,,,,,,,,,,\"6-25T\"
,\"E710\",\"0001\",\"读取控制板\",,,,,\"电源ON时,读取控制板内的IPC不能进行初始化\"
,\"E710\",\"0002\",\"DC控制板\",,,,,\"电源ON时,DC控制板内的IPC不能进行初始化\"
,\"E710\",\"0003\",\"主控制板\",,,,,\"电源ON时,主控制板内的IPC不能进行初始化\"
,,,\"通信不良\",,,,,,,,,,,,,\"6-26T\"
,\"E711\",\"0001\",\"IPC通信不良\",,,,,\"1.5秒以内向读取控制电路板的IPC的出错记录的数据写入达4次以上\"
,,\"0002\",\"IPC通信不良\",,,,,\"1.5秒以内向DC控制电路板的IPC的出错记录的数据写入达4次以上\"
,,\"0003\",\"IPC通信不良\",,,,,\"1.5秒以内向主控制电路板的IPC的出错记录的数据写入达4次以上\"
,\"E712\",\"0001\",\"IPC通信不良\",,,,,\"向ADF控制板上的IPC的出错记录写入数据后经过3秒通信不能恢复\"
,,\"0002\",\"IPC通信不良\",,,,,\"在读取控制电路板的IPC的同步记录中,经过10秒信息发送位仍未起动\"
,\"E713\",,\"IPC通信不良\",,,,,\"复印机检测到复印机与Finisher控制板之间通信中断\"
,,,\"选购件\",,,,,,,,,,,,,\"6-29T\"
,\"E716\",\"0000\",\"复印机纸盘工作台\",,,,,\"检测到复印机纸盘工作台后在预定的周期内未检测到ID信号\"
,\"E717\",\"0001\",\"复印数据或NE控制器通信不良\",,,,,\"复印数据或NE控制器通信不良,进入维修程序模式,选择COPIER>FUNCTION>CLEAR>ERR 清除故障码\"
,\"E719\",\"0001\",\"投币机与主控制板通信不良\",,,,,\"投币机与主控制板通信不良,进入维修程序模式,选择COPIER>FUNCTION>CLEAR>ERR 清除故障码\"
,\"E732\",\"0001\",\"读取控制板与主控制板通信不良\",,,,,\"主控制板检测到读取控制板与主控制板通信不良\"
,\"E733\",\"0001\",\"DC控制板与主控制板通信不良\",,,,,\"DC控制板与主控制板通信不良\"
,\"E737\",\"0000\",\"DRAM检测出错\",,,,,\"电源ON后,DRAM检测到主控制板有故障\"
,\"E740\",\"0001\",\"LAN卡,主控制板出错\",,,,,\"电源ON时,在复印机插有LAN卡时检测到LAN网络卡出错\"
,\"E740\",\"0002\",\"LAN卡,主控制板出错\",,,,,\"检测到MAC地址出错\",,,,,,,,\"6-32T\"
,\"E740\",\"0003\",\"LAN卡,主控制板出错\",,,,,\"不能读出LAN网络卡地址\"
,\"E741\",,\"PCI总线异常\",,,,,\"PCI总线异常,可进入BOARD>OPTION,选择PIC1-OFF或PIC2-OFF或PIC3-OFF将出错的PIC口关闭\"
,\"E742\",,\"RIPI卡自检时检测到异常\",,,,,\"RIPI卡自检时检测到异常\"
,\"E743\",,\"读取控制板与主控制板通信不良\",,,,,\"读取控制板检测到读取控制板与主控制板通信不良\"
,\"E744\",,\"主板BOOT ROM和系统与软件出错\",,,,,\"主控制板上的BOOT ROM和系统与软件属于不同机型或不同类型\"
,\"E803\",\"0000\",\"电源板故障\",,,,,\"主电源板上 24V电源没有输出达1秒\",,,,,,,,\"6-34T\"
,,,\"风扇锁住故障\",,,,,,,,,,,,,\"6-35T\"
,\"E805\",\"0001\",\"显影排风扇(FM1)故障\",,,,,\"显影排风扇(FM1)在运转但5秒以上未收到FM1LCK同步信号\"
,\"E805\",\"0002\",\"定影排风扇(FM2)故障\",,,,,\"定影排风扇(FM2)在运转但5秒以上未收到FM2LCK同步信号\"
,\"E805\",\"0003\",\"电路部分排风扇(FM3)故障\",,,,,\"电路部分排风扇(FM3)在运转但5秒以上未收到FM3LCK同步信号\"
,\"E805\",\"0004\",\"卷曲减少风扇(FM4)故障\",,,,,\"卷曲减少风扇(FM4)在运转但5秒以上未收到FM4LCK同步信号\"
,\"E805\",\"0005\",\"卷曲减少风扇(FM5)故障\",,,,,\"卷曲减少风扇(FM5)在运转但5秒以上未收到FM5LCK同步信号\"
,,,\"输稿器(DADF-H1)部分的故障码\",,,,,,,,,,,,,\"6-37T\"
,\"E420\",\"0001\",\"EEPROM,ADF控制板\",,,,,\"电源ON时,不能读取EEPROM的后备数据时,或读取的数据异常\"
,\"E421\",\"0001\",\"EEPROM,ADF控制板\",,,,,\"电源ON时,不能在EEPROM上写入后备数据时,或写入的数据异常\"
,\"E422\",\"0001\",\"与复印机通信不良\",,,,,\"待机时输稿器(DADF-H1)和复印机通信中断达5秒;或DADF动作过程中和复印机通信中断达5秒\"
,,,\"选购件鞍式分页装订器-G1的故障码\",,,,,,,\"Saddle Finisher-G1\",,,,,,\"6-38T\"
,,,\"Finisher/Saddle单元\"
,\"E713\",,\"数据通信出错\",,,,,,,\"复印机检测到复印机与Finisher控制板之间通信中断\"
,\"E501\",\"0001\",\"数据通信不良\",,,,,,,\"分页器和打孔器电路板通信不良\"
,\"E505\",\"0001\",\"EEPROM出错\",,,,\" \",\" \",,\"电源ON时分页器控制板后援存储器EEPROM检查总和出错\"
,\"E505\",\"0002\",\"EEPROM出错\",,,,\" \",,,\"电源ON时打孔器控制板EEPROM检查总和出错\"
,\"E510\",\"0001\",\"纸输入电机M1,堆垛输送辊原位传感器PI12(上)\",,,,,,,\"纸输入电机驱动2秒后,堆垛输送辊未离开原位传感器PI12(上)\"
,\"E510\",\"0002\",\"纸输入电机M1,堆垛输送辊原位传感器PI12(上)\",,,,,,,\"纸输入电机驱动2秒后,输送辊未返回到原位传感器PI12(上)\"
,\"E514\",\"0001\",\"纸堆垛处理后排纸步进电机M3,排纸皮带原位PI7\",,,,,,,\"纸堆垛处理后排纸步进电机M3驱动3秒后,排纸皮带未离开原位PI7\"
\" \",\"E514\",\"0002\",\"纸堆垛处理后排纸步进电机M3,排纸皮带原位PI7\",,,,,,,\"纸堆垛处理后排纸步进电机M3驱动3秒后,排纸皮带未返回到原位PI7\"
,\"E530\",\"0001\",\"后拍纸整理电机M5,拍纸整理板原位传感器PI5\",,,,,,,\"电机ON后3秒,后拍纸整理板未离开后拍纸整理板原位传感器PI5\"
\" \",\"E530\",\"0002\",\"后拍纸整理电机M5,拍纸整理板原位传感器PI5\",,,,,,,\"电机ON后3秒,后拍纸整理板未返回到后拍纸整理板原位,PI5\"
,\"E531\",\"0001\",\"鞍式装订/对折纸电机M7,装订器原位传感器PI19\",,,,,,,\"电机ON后0.6秒,未离开装订器原位传感器PI19\"
,\"E531\",\"0002\",\"鞍式装订/对折纸电机M7,装订器原位传感器PI19\",,,,,,,\"电机ON后0.6秒,未返回到装订器原位传感器PI19\"
,\"E531\",\"0003\",\"鞍式装订/对折纸电机M7;电机时钟传感器PI14\",,,,,,,\"电机ON驱动后,机时钟传感器PI14有0.1秒未检到测脉冲\"
,\"E5F1\",\"0001\",\"鞍式装订/对折纸电机M7,折纸辊原位传感器PI11\",,,,,,,\"电机ON后1.5秒,折纸辊未离开折纸辊原位传感器PI11\"
,\"E5F1\",\"0002\",\"鞍式装订/对折纸电机M7,折纸辊原位传感器PI11\",,,,,,,\"电机ON后3.5秒,折纸辊未返回到折纸辊原位传感器PI11\"
,\"E5F1\",\"0003\",\"鞍式装订/对折纸电机M7,折纸辊原位传感器PI11\",,,,,,,\"电机ON驱动后,机时钟传感器PI14有1秒未检到测脉冲\"
,\"E532\",\"0001\",\"装订器滑动电机M8,滑动原位传感器PI18\",,,,,,\" \",\"电机ON后4.5秒,未离开装订器滑动原位传感器PI180\"
\" \",\"E532\",\"0002\",\"装订器滑动电机M8,滑动原位传感器PI18\",,,,,,,\"电机ON后4.5秒,未离返回到装订器滑动原位传感器PI18\",,,,,,,,\" \"
\" \",\"E537\",\"0001\",\"前拍纸整理电机M4,整理板原位传感器PI4\",,,,,,\" \",\"电机ON后3秒,前拍纸整理板未离开前拍纸整理板原位传感器PI4\"
,\"E537\",\"0002\",\"前拍纸整理电机M4,整理板原位传感器PI4\",,,,,,,\"电机ON后3秒,前拍纸整理板未返回到前拍纸整理板原位,PI4\"
,\"E540\",\"0001\",\"排出的纸接纸托盘电机M6驱动后,纸表面传感器PI9\",,,,,,,\"排出的纸接纸托盘升降电机M6驱动后,纸表面传感器PI9保持ON达10秒\"
,\"E540\",\"0002\",\"排纸托盘上升时,托盘上限传感器PI15激励\",,,,,,,\"排出的纸接纸托盘升降电机M6驱动后上升时检测到排纸托盘上限传感器PI15 ,ON\"
,\"E540\",\"0003\",\"排纸托盘升降电机时钟传感器PI17\",,,,,,,\"排出的纸接纸托盘升降电机M6驱动后,排纸托盘升降电机时钟传感器PI17有10秒未检到测脉冲\"
,\"E550\",\"0010\",\"鞍式分页装订器-G1的 Finisher单元电源故障\",,,,,,,\"鞍式分页装订器-G1的 分页器Finisher单元电源故障\"
,\"E577\",\"0001\",\"蹼轮电机M2,蹼轮原位传感器PI2\",,,,,,,\"蹼轮电机M2驱动后2秒,蹼轮未离开原位传感器PI2\"
,\"E577\",\"0002\",\"蹼轮电机M2,蹼轮原位传感器PI2\",,,,,,,\"蹼轮电机M2驱动后2秒,蹼轮未返回到原位传感器PI2\"
,\"E577\",\"0003\",\"蹼轮电机M2,托盘升降电机M6\",,,,,,,\"蹼轮电机M2驱动后2秒,排纸托盘升/降导板未离开原位\"
,\"E577\",\"0004\",\"蹼轮电机M2,托盘升降电机M6\",,,,,,,\"蹼轮电机M2驱动后2秒,排纸托盘升/降导板未返回到原位\"
,,,\"Puncher打孔组件\",,,,,,,\"Puncher打孔单元-J1:2孔;Puncher打孔单元-K1:2/3孔;Puncher打孔单元-G1:4孔;Puncher打孔单元-H1:4孔;\"
,\"E501\",\"00FF\",\"数据通信出错\",,,,,,,\"Puncher打孔单元间通信中断\"
,\"E505\",\"0020\",\"EEPROM出错\",,,,,,,\"电源ON时Puncher打孔单元控制板后援存储器EEPROM检查总和出错\"
,\"E550\",\"0020\",\"鞍式分页装订器-G1的Puncher电源故障\",,,,,,,\"鞍式分页装订器-G1的打孔单元Puncher的 24V电源故障\"
,\"E590 \",\"0001\",\"打孔原位传感器PI1P;打孔电机M1P\",,,,,,,\"打孔电机M1P转动250毫秒后,打孔器未返回到原位,PI1P\",,,,,,,,\" \"
,\"E590 \",\"0002\",\"打孔机电机时钟传感器PI3P;打孔电机M1P\",,,,,,\" \",\"打孔电机M1P转动后,电机时钟传感器PI3P有60毫秒未检测到脉冲\"
,\"E592\",\"0001\",\"水平对位传感器自动调整故障\",,,,,,,\"传感器自动调整时,光发射电压设定在4.4V光接收电压小于2.5V\"
,\"E592\",\"0002\",\"水平对位传感器自动调整故障\",,,,,,,\"传感器自动调整时,光发射电压设定在0V光接收电压大于2.5V\"
,\"E592\",\"0003\",\"水平对位传感器自动调整故障\",,,,,,,\"传感器输出自动调整后,光发射电压大于4.4V\"
,\"E592\",\"0004\",\"水平对位传感器自动调整故障\"
,\"E592\",\"0005\",\"水平对位传感器自动调整故障\"
,\"E592\",\"0006\",\"打孔器废孔纸满传感器PT131\",,,,,,,\"图4.1,打孔器废孔纸满传感器PT131检测信号DUSTPTR,检测到废孔纸满\"
,\"E593\",\"0001\",\"水平(横向)对位原位传感器PI2P;对位电机M2P\",,,,,,,\"打孔水平(横向)对位电机转动1秒,打孔器未离开横向对位原位传感器PI2P\"
,\"E593\",\"0002\",\"水平(横向)对位原位传感器PI2P;对位电机M2P\",,,,,,,\"打孔水平(横向)对位电机转动秒,打孔器未返回到横向对位原位传感器PI2P\",,,,,,,,\" \"
,,,\"选购件分页器-J1的故障码\",,,,,,,\"Finisher-J1\",,,,,,\"6-43T\"
,\"E500\",\"0000\",\"数据通信不良\",,,,,,,\"复印机与分页器之间通信中断在5秒内未恢复\"
,\"E514\",\"0000\",\"堆垛处理电机M2\",,,,,,,\"堆垛排纸前进驱动后,堆垛排纸杆原位传感器S8未OFF\"
,\"E585\",\"0000\",\"堆垛处理电机M2\",,,,,,,\"堆垛排纸返回驱动后,堆垛排纸杆原位传感器S8未ON\"
,\"E530\",\"0000\",\"后拍纸整理电机M4,后拍纸整理板原位传感器S7\",,,,,,,\"电机ON后,后拍纸整理板未离开后拍纸整理板原位传感器S7\"
\" \",\"E530\",\"0000\",\"后拍纸整理电机M4,后拍纸整理板原位传感器S7\",,,,,,,\"电机ON后,后拍纸整理板未返回到后拍纸整理板原位传感器S7\"
,\"E531\",\"0000\",\"装订电机M6,装订电机原位传感器S16\",,,,,,,\"装订电机M6前进驱动后,装订电机原位传感器S16未OFF\"
,\"E531\",\"0000\",\"装订电机M6,装订电机原位传感器S16\",,,,,,,\"装订电机M6返回驱动后,装订电机原位传感器S16未ON\"
\" \",\"E537\",\"0000\",\"前拍纸整理电机M3,整理板原位传感器S6\",,,,,,\" \",\"电机ON后3秒,前拍纸整理板未离开前拍纸整理板原位传感器S6\"
,\"E537\",\"0000\",\"前拍纸整理电机M3,整理板原位传感器S6\",,,,,,,\"电机ON后3秒,前拍纸整理板未返回到前拍纸整理板原位,S6\"
,\"E577\",\"0000\",\"堆垛输送电机M1,返回轮原位传感器S3\",,,,,,,\"堆垛输送电机M1返回驱动后,返回轮原位传感器S3未ON\"
,\"E580\",\"0000\",\"排纸托盘上升时,排纸托盘上限传感器S13\",,,,,,,\"排纸托盘升降电机M5驱动上升4秒后,排纸托盘上限传感器S13未ON\"
,\"E580\",\"0000\",\"排纸托盘下降时,排纸托盘上限传感器S13\",,,,,,,\"排纸托盘升降电机M5驱动下降4秒后,排纸托盘上限传感器S13未OFF\"
,\"E580\",\"0000\",\"排纸托盘升降电机M5时钟传感器S9\",,,,,,,\"排纸托盘升降电机M5驱动后,排纸托盘电机时钟传感器S9有0.8秒未检测到脉冲\"
,\"E580\",\"0000\",\"排纸托盘升降电机M5驱动后,排纸高度传感器S10\",,,,,,,\"排纸托盘升降电机M5驱动上升时,检测到排纸托盘上限传感器PI15 ,ON\"
,\"E590 \",\"0001\",\"打孔原位传感器PI1P;打孔电机M1P\",,,,,,,\"打孔电机M1P转动250毫秒后,打孔器未返回到原位,PI1P\",,,,,,,,\" \"
,\"E590 \",\"0002\",\"打孔原位传感器PI1P;打孔电机M1P\",,,,,,\" \",\"打孔电机M1P转动后,电机时钟传感器PI3P有60毫秒未检测到脉冲\"
,\"纸盘工作台-W1\"
,\"E901 \",\"0000\",\"纸盘工作台-W1主电机M1C\",,,,,,,\"纸盘工作台-W1主电机M1C驱动1.3秒后,\"
,,,,,\"CANON 佳能 iR2200/iR2800/iR3300 数码复印机维修程序\"
,\"1.1概要:维修程序画面由初始画面→大/中项目画面→小项目画面3个阶段构成\",,,,,,,,,,,,,,\"5-3T\"
,,\"维修程序模式共有7种\"
,,,\"No.\",,\"画面显示\"
,,,\"1\",,\"DISPLY\",,,\"显示模式\"
,,,\"2\",,\"I/O DISPLY\",,,\"输入/输出显示模式\"
,,,\"3\",,\"ADJUST\",,,\"调整模式\"
,,,\"4\",,\"FUNCTION\",,,\"动作/检查模式\"
,,,\"5\",,\"OPTION\",,,\"规格设定模式\"
,,,\"6\",,\"TEST\",,,\"测试打印模式\"
,,,\"7\",,\"COUNTER\",,,\"计数器模式\"
,\"1.2维修程序模式的进入\",,,,,,,,,,,,,,\"5-3T\"
,,\"1,按面板操作部的用户方式(星号\\\"*\\\")键\"
,,\"2,同时按住数字键\\\"2\\\"和\\\"8\\\"\"
,,\"3,再按面板操作部的用户方式(星号\\\"*\\\")键\"
,,\"液晶显示屏显示出维修程序模式的初始画面\"
,,,\"CPOIER\",,,,,\"复印机的维修程序模式\"
,,,\"FEEDER\",,,,,\"进稿器(ADF)的维修程序模式\",,,,,,\"(显示FEEDER表示选购件输稿器已连接)\"
,,,\"SORTER\",,,,,\"分页器的维修程序模式\",,,,,,\"(显示SORTER表示选购件分页器已连接)\"
,,,\"FAX\",,,,,\"传真机的维修程序模式\",,,,,,\"(显示FAX表示选购件的功能扩充板已连接)\"
,,,\"BOARD\",,,,,\"功能扩充板的维修程序模式\",,,,,,\"(显示BOARD表示选购件的功能扩充板已连接)\"
,\"1.3退出维修程序模式\",,,,,,,,,,,,,,\"5-3T\"
,,\"1,按1次复位键\\\" 〃 \\\",退出当前模式返回到维修程序模式的初始画面\"
,,\"2,按2次复位键\\\" 〃 \\\",退出维修程序模式返回到标准画面\"
,,\"注:使用维修程序的(ADJUST调整模式),(FUNCTION动作确认模式),\"
,,,\"(OPTION机器选购件功能设定模式)情况下退出维修程序模式后必须将主电源开关OFF后再ON.\"
,\"1.4维修程序模的后备设置\"
,,\"出厂时机器的调整值记录在维修标签上贴在前盖板内,读取控制板或DC控制板更换后,要将旧板上的EEPROM取下安装到新板上;RAM清除后,\"
,,\"调整后的(ADJUST调整模式),(OPTION机器选购件功能设定模式),的值恢复到缺省值,更改维修程序模的值时必须登记到维修标签上;\"
,,\"在维修程序模CPOIER复印的FUNCTION>MISC-P>P-PRINT\\\"[打印维修模式(ADJUST,OPTION,COUNTER)的内容\\\"],\"
,,,\"将选择P-PRINT项,显示反转后按OK键,可将维修模式当前值的清单一次全部打印出来.\"
,\"1.5基本操作\",,,,,,,,,,,,,,\"5-5T\"
,\"1.5.1 初始画面\"
,,\"液晶显示屏显示出维修程序模式的初始画面\"
,,,\"CPOIER\",,,,,\"复印机的维修程序模式\",,,,\"5-6T\"
,,,\"FEEDER\",,,,,\"进稿器(ADF)的维修程序模式\",,,,\"5-95T\",,\"(显示FEEDER表示选购件输稿器已连接)\"
,,,\"FAX\",,,,,\"传真机的维修程序模式\",,,,,,\"(显示FAX表示选购件的功能扩充板已连接)\"
,,,\"SORTER\",,,,,\"分页器的维修程序模式\",,,,\"5-95T\",,\"(显示SORTER表示选购件分页器已连接)\"
,,,\"BOARD\",,,,,\"功能扩充板的维修程序模式\",,,,\"5-96T\",,\"(显示BOARD表示选购件功能扩充板已连接)\"
,\"1.5.2\",\"大/中项目画面→小项目画面\",,,,,,,,,,\"5-6T\"
,,\"大项目画面\",,\"→\",,\"Display\",,\"I/O\",,\"Adjust\",,,\"Function\",,,\"Option\",,,\"Test\"
,,,,,,\"VERSION\",,,,,,\"显示ROM版本\"
,,,,,,\"USER\",,,,,,\"显示用户画面,有关用户项目\"
,,,\"中项目画面\",,\"→\",\"ACC-STS\",,,,,,\"显示选购件的接入状态\"
,,,,,,\"ANALOG\",,,,,,\"显示模拟传感器的测定值\"
,,,,,,\"CST-STS\",,\"SENSOR\",,,,\"显示纸盒的使用状况\",,,,,,\"显示传感器状态\"
,,,,,,\"JAM\",,\"MISC\",,,,\"显示卡纸数据\",,,,\"其他调整\"
,,,,,,\"ERR\",,,,,,\"显示故障码\"
,,,,,,\"HV-STS\",,\"ALARM-2\",,,,\"显示高压电压,电流的测定值\",,,,,,\"显示最新报警码-2\"
,\"5.1.3\",,\"小项目画面\"
,,,,,,\"Display\",,,\"I/O\",,\"Adjust\",,\"Function\",,,\"Option\",,,\"Test\",,\"Counter\"
,,,,,\"中项目画面\",,\"→\",\"\",,,,,\"\",,\"←共2页的第1页\",,,\"\",,\"维修/复印可以接受\"
,,,,,\"小项目画面\",,\"→\"
,,,,,,,,,\"DC-CON\",,,,,\"显示主控板用的DIMM(Flush-ROM)版本\"
,,,,,,,,,\"R-CON\",,,,,\"显示读取控制板用DIMM(Flush-ROM)版本\"
,,,,,,,,,\"PANEL\",,,,,\"显示操作面板用的ROM版本\"
,,,,,,,,,\"FEEDER\",,,,,\"显示输稿器控制板的ROM版本\"
,,,,,,,,,\"SORTER\",,,,,\"显示分页器控制板的ROM版本\"
,,,,,,,,,\"NIB\",,,,,\"显示网络软件的版本\"
,,,,,,,,,\"PS/PCL\",,,,,\"显示打印卡(PS/PCL)的版本\"
,,,,,,,,,\"LIPS\"
,,,,,\"退到前一页→\",,,\"←\",,,,\"←\",,\"←进入下一页\"
,,,,,\"注:\",\" 表示在位置可显示以下的项目:\"
,,,,,,\"\",,,\"在维修模式下可以进行复印\"
,,,,,,\"\",,,\"发生卡纸\",,,,,,\"\",,,\"发生出错\"
,,,,,,\"\",,,\"正在进行维修\",,,,,,\"\",,,\"没有墨粉\"
,,,,,,\"\",,,\"正在进行前回转等动作\",,,,,,\"\",,,\"废粉仓已满\"
,,,,,,\"\",,,\"机门打开\",,,,,,\"\",,,\"无纸\"
,,,,,,\"\",,,\"正在进行复印\",,,,,,\"\",,,\"没有复印动作\"
,,,\"Display\",,,\"I/O\",,\"Adjust\",,\"Function\",,,\"Option\",,,\"Test\",,\"Counter\"
,,,,,\"\",,,,,\"\",,,,,\"\"
,,,\"ADJ-X\",,,\"×××××\",,\"(yyyyy)\",,,\"aaaaa\",,\"～\",\"bbbbb\"
,,,\"↑ 按该项目后显示反转\"
,,,,,,\"×××××\",\"变更前的数值\",,,\"yyyyy\",\"输入的变更数值\",,,\"aaaaa～bbbbb\",,\"可输入的变更数范围\"
,,\"退到前一页→\",,,\"←\",,,\"←\",,\"←进入下一页\",,,,\" /—\",,,\"OK\"
,,,,,,,,,,,,\"数值的加/减改变↑\",,,,,\"↑输入数的确认\"
,\"2.\",\"复印>显示控制模式\",,,,,\"COPIER复印>DISPLAY显示\",,,,,,,,\"5-6T\"
,\"2.1 复印>显示控制模式的液晶显示屏画面\",,,,,,,,\"COPIER>DISPLAY\"
,,,\"Display\",,,\"I/O\",,\"Adjust\",,\"Function\",,,\"Option\",,,\"Test\",,\"Counter\"
,,,\"VERSION\",,,,,,\"显示ROM版本\"
,,,\"USER\",,,,,,\"显示用户画面,有关用户项目\"
,,,\"ACC-STS\",,,,,,\"显示选购件的接入状态\"
,,,\"ANALOG\",,,,,,\"显示模拟传感器的测定值\"
,,,\"CST-STS\",,,\"SENSOR\",,,\"显示纸盒的使用状况\",,,,,,\"显示传感器状态\"
,,,\"JAM\",,,,,,\"显示卡纸数据\"
,,,\"ERR\",,,,,,\"显示故障码\"
,,,\"HV-STS\",,,\"ALARM-2\",,,\"显示高压电压,电流的测定值\",,,,,,\"显示最新报警码-2\"
,\"显示复印机和选购件板用的ROM版本\",,,,,,,\"COPIER复印>DISPLAY>VERSION\",,,,,,,\"5-7T\"
,\"COPIER>DISPLAY>VERSION>DC-CON\",,,,,,,\"显示DC控板用ROM)版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>R-CON\",,,,,,,\"显示读取控制板用DIMM(Flush-ROM)版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>PANEL\",,,,,,,\"显示操作面板的CPU控制板用ROM版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>FEEDER\",,,,,,,\"显示输稿器控制板用ROM版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>SORTER\",,,,,,,\"显示分页器控制板用ROM版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>NIB\",,,,,,,\"显示网络软件的版本\"
,\"COPIER>DISPLAY>VERSION>PS/PCL\",,,,,,,\"显示打印卡(PS/PCL)的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LISP\",,,,,,,\"显示打印卡(LISP)的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>MN-CONT\",,,,,,,\"显示主控板用软件的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>BOOT-ROM\",,,,,,,\"显示主控板BOOT-ROM版本\",,,,,,,\"显示:复印模式,XX.YYC;PSPCL打印卡模式XX,YYP;PCL打印卡XX,YYL\"
,\"COPIER>DISPLAY>VERSION>DIGA-DVC\",,,,,,,\"显示自诊断装置的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>RUI\",,,,,,,\"显示RUI的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>PUNCH\",,,,,,,\"显示打孔器软件的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-EN\",,,,,,,\"显示英语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-FR\",,,,,,,\"显示法语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-DE\",,,,,,,\"显示德语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-IT\",,,,,,,\"显示意大利语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-JP\",,,,,,,\"显示日语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-CS\",,,,,,,\"显示捷克语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-DA\",,,,,,,\"显示丹麦语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-EL\",,,,,,,\"显示希腊语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-ES\",,,,,,,\"显示西班牙语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-ET\",,,,,,,\"显示爱沙尼亚语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-FI\",,,,,,,\"显示芬兰语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-HU\",,,,,,,\"显示匈牙利语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-KO\",,,,,,,\"显示伊斯兰语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-NL\",,,,,,,\"显示荷兰语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-NO\",,,,,,,\"显示挪威语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-PL\",,,,,,,\"显示波兰语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-PT\",,,,,,,\"显示葡萄牙语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-RU\",,,,,,,\"显俄罗斯语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-SL\",,,,,,,\"显示斯洛文尼亚语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-SV\",,,,,,,\"显示瑞典语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-TW\",,,,,,,\"显示繁体中文语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"COPIER>DISPLAY>VERSION>LANG-ZH\",,,,,,,\"显示简体中文语语言的版本\",,,,,,,\"XX:版本号;YY:开发管理号\"
,\"显示用户画面设置的语言及有关项目\",,,,,,,,\"USER\",,,,,,\"5-10T\"
,\"COPIER>DISPLAY>USER>LANGUAGE\",,,,,,,\"显示用户画面设置的语言文字及有关项目\",,,,,,,\"XXYY.ZZ.AA\"
,,,,,,,,,,,,,,,\"XX:国家码(见Jis);YY语言码(见ISO639)\"
,,,,,,,,,,,,,,,\"ZZ:适应码(00:佳能模式 ,01:OEM模式,02:公用(全部));AA:复印纸码\"
,,,,,,,,,,,,,,,\"(00:AB系列;01:英制系列;02:A系列;03:AB/英制系列)\"
,\"COPIER>DISPLAY>USER>MODEL\",,,,,,,\"机型\",,,,,,,\"0: iR2200; 1: Ir2800;2: iR3300\"
,\"显示选购件的连接状态\",,,,,,,\"ACC-STS\",,,,,,,\"5-10T\"
,\"COPIER>DISPLAY>ACC-STS>FEEDER\",,,,,,,\"显示输稿器连接状态\",,,,,,,\"0:ADF未按装; 1: ADF已按装\"
,\"COPIER>DISPLAY>ACC-STS>SORTER\",,,,,,,\"显示分页器连接状态\",,,,\"XY\",,,\"X=0:分页器未安装 ; 1:分页器 ; 2:鞍式分页器\"
,,,,,,,,,,,,,,,\"Y=0:打孔机未安装 ;1: 2孔的打孔机; 2: 3孔的打孔机; \"
,,,,,,,,,,,,,,,\"3: 4孔的打孔机(FRN); 4: 4孔的打孔机(SWDN)\"
,\"COPIER>DISPLAY>ACC-STS>DECK\",,,,,,,\"显示3500张(L1)右侧纸仓连接状态\",,,,,,,\"0:未按装; 1: 已按装\"
,\"COPIER>DISPLAY>ACC-STS>CARD\",,,,,,,\"显示控制卡连接状态\",,,,,,,\"0:CARD未按装; 1: CARD已按装\"
,\"COPIER>DISPLAY>ACC-STS>DATA-CON\",,,,,,,\"显示显示自诊断装置的连接状态\",,,,,,,\"0:未按装; 1: 复印数据控制卡板已按装; 2: NE控制卡已按装\"
,\"COPIER>DISPLAY>ACC-STS>RAM\",,,,,,,\"显示复印机主板的RAM总容量\",,,,,,,\"64MB ; 128MB\"
,\"COPIER>DISPLAY>ACC-STS>NIB\",,,,,,,\"显示网络卡的RAM连接状态\",,,,,,,\"0:未按装; 1: 以太网络卡已按装; \"
,,,,,,,,,,,,,,,\"2: 令牌环网络卡已按装;3: 以太网络卡和令牌环网络卡都能用\"
,\"COPIER>DISPLAY>ACC-STS>LIPS-RAM\",,,,,,,\"显示打印卡(LISP)的RAM总容量\",,,,,,,\"xxMB\"
,\"COPIER>DISPLAY>ACC-STS>LISP\",,,,,,,\"显示打印卡(LISP)的连接状态\",,,,,,,\"0:未按装; 1: 已按装; \"
,\"COPIER>DISPLAY>ACC-STS>PS/PCL\",,,,,,,\"显示打印卡(PS/PCL)的连接状态\",,,,,,,\"0:未按装; 1: PS/PCL已按装; 2: PS汉字\"
,\"COPIER>DISPLAY>ACC-STS>NETWARE\",,,,,,,\"显示NETWARE的连接状态\",,,,,,,\"0:未按装; 1: 已按装\"
,\"显示模拟传感器的测定值\",,,,,,,\"ANALOG\",,,,,,,\"5-11T\"
,\"COPIER>DISPLAY>ANALOG>TMPE\",,,,,,,\"显示环境传感器检测到的机内温度\",,,,,,,\"单位℃\"
,\"COPIER>DISPLAY>ANALOG>HUM\",,,,,,,\"显示环境传感器检测到的机内相对湿度\",,,,,,,\"单位%RH\"
,\"COPIER>DISPLAY>ANALOG>ABS-HUM\",,,,,,,\"机内湿度绝对值\",,,,,,,\"单位g\"
,\"COPIER>DISPLAY>ANALOG>DR-TMPE\",,,,,,,\"显示OPC鼓周围温度\",,,,,,,\"单位℃\"
,\"COPIER>DISPLAY>ANALOG>FIX-C\",,,,,,,\"显示主热敏电阻M-TH1检测到定影薄膜中间的温度\",,,,,,,\"单位℃ \"
,\"COPIER>DISPLAY>ANALOG>FIX-E\",,,,,,,\"显示副热敏电阻S-TH2检测到定影薄膜边缘的温度\",,,,,,,\"单位℃\"
,\"显示纸盒的纸宽度和纸尺寸\",,,,,,,\"CST-STS\",,,,,,,\"5-12T\"
,\"COPIER>DISPLAY>CST-STS>WIDTH-MF\",,,,,,,\"50张手进纸纸盘纸宽(毫米),纸尺寸\",,,,,,,\"宽度以整数表示,小数部分不表示\"
,\"显示卡纸故障历史档案\",,,,,,,\"COPIER>DISPLAY>JAM\",,,,,,,\"5-13T\"
,,,\"Display\",,,\"I/O\",,\"Adjust\",,\"Function\",,,\"Option\",,,\"Test\",,\"Counter\"
,,,\"AA\",,\"BBBB\",,\"CCCC\",\"DDDD\",,\"E\",,\"FFff\",,\"G\",\"HHHHHH\",,,\"IIIII\"
,,,,\"←\",,,\"→\",,,,,,\" /—\",,,,\"OK\"
,,,\"AA\",,,,\"卡纸发生的序号1～50,数字大卡纸发生的时间早\"
,,,\"BBBB\",,,,\"卡纸发生的月,日 (前2位表示月,后2位表示日)\"
,,,\"CCCC\",,,,\"卡纸发生的时间 (显示24小时)\"
,,,\"DDDD\",,,,\"卡纸恢复的时间 (显示24小时)\"
,,,\"E\",,,,\"卡纸发生的部位 (0:主机;1输稿器;2:分页器)\"
,,,\"FFFF\",,,,\"卡纸发生的种类和卡纸检测传感器 (前2位表示卡纸种类,后2位表示卡纸检测传感器)\"
,,,\"前2位FF表示卡纸种类:\",,,,\"00:无;01:延迟卡纸;02:滞留卡纸;0A:电源ON时纸残留卡纸;0B:复印时门打开卡纸;\"
,,,,,,,\"9003:逻辑卡纸(分页器-J1待机卡纸);9011:逻辑卡纸(图像无请求卡纸);10XX:分页器卡纸\"
,\"5-14T\",,\"后2位ff表示卡纸检测传感器\"
,,,,\"01\",\"对位传感器PS10\",,,,,,,,,\"13\",\"No.1接纸盘(机内基本接纸盘)排纸检测传感器PS15\"
,,,,\"02\",\"手送纸传感器PS28\",,,,,,,,,\"14\",\"No.2接纸盘(内置2路接纸托盘的上层)排纸检测传感器PS19B\"
,,,,\"03\",\"预对位传感器PS9\",,,,,,,,,\"15\",\"No.3接纸盘(外置接纸托盘)排纸检测传感器PS21B\"
,,,,\"04\",\"选购件纸盒工作台W1的纵向输纸道的输纸传感器Q1603\",,,,,,,,,\"21\",\"双面纸盘(单张纸盘)纸张进入传感器PS18\"
,,,,\"05\",\"前置纸盒1再进纸传感器PS7\",,,,,,,,,\"22\",\"双面纸盘(单张纸盘)纸张排出传感器PS18\"
,,,,\"06\",\"前置纸盒2再进纸传感器PS8\",,,,,,,,,\"33\",\"前门开关SW3打开\"
,,,,\"07\",\"选购件纸盒工作台W1的前置纸盒3再进纸传感器PS2C\",,,,,,,,,\"34\",\"右门开/关检测传感器PS23\"
,,,,\"08\",\"选购件纸盒工作台W1的前置纸盒4再进纸传感器PS3C\",,,,,,,,,\"35\",\"No.2接纸盘(内置2路纸托盘的上层)排纸开/关检测传感器PS24B\"
,,,,\"09\",\"选购件3500张右侧纸仓(L1)搓纸传感器PS1D(P-OUT-SENS)\",,,,,,,,,\"36\",\"选购件纸盒工作台W1的右门开/关检测传感器PS1C\"
,,,,\"0A\",\"选购件3500张右侧纸仓(L1)输纸传感器PS6D(FEED-SENS)\",,,,,,,,,\"37\",\"选购件3500张右侧纸仓(L1)连接到复印机检测传感器PS5D(DECK-MOUNT-SENS=1)\"
,,,,\"11\",\"纸前沿到达鼓前端的图像前沿传感器PS12,开始激光曝光\",,,,,,,,,\"39\",\"分页器前盖打开\"
,,,,\"12\",\"定影出口纸输送辊传感器PS13\"
,,,,,\"输稿器(DADF)卡纸检测传感器\",,,,,,,,,\"内置分页器Finisher-J1\"
,,,,,\"FFff\",\"卡纸检测传感器/卡纸类别\",,,,\"相关传感器\",,,,\"FFff\",\"卡纸检测传感器/卡纸类别\",,,,,\"相关传感器\"
,,,,,\"0001\",\"对位传感器延迟卡纸\",,,,\"PI6\",,,,\"0003\",\"入口传感器延迟卡纸\",,,,,\"S2\"
,,,,,\"0002\",\"对位传感器滞留卡纸\",,,,\"PI6\",,,,\"0004\",\"入口传感器滞留卡纸\",,,,,\"S2\"
,,,,,\"0003\",\"读取传感器延迟卡纸\",,,,\"PI6;PI7\",,,,\"0006\",\" 装订器装订针卡纸\",,,,,\"S17\"
,,,,,\"0004\",\"读取传感器滞留卡纸\",,,,\"PI7\",,,,\"0007\",\"电源ON卡纸\",,,,,\"S2\"
,,,,,\"0005\",\"输纸传感器延迟卡纸\",,,,\"PI7;PI8\",,,,\"0081\",\"堆垛推出\",,,,,\"S8\"
,,,,,\"0006\",\"输纸传感器滞留卡纸\",,,,\"PI8\",,,,\"0082\",\"堆垛返回\",,,,,\"S3\"
,,,,,\"0007\",\"RADF打开\",,,,\"PI1\",,,,\"0114\",\"中继纸排出传感器延迟卡纸\",,,,,\"PS19Z\"
,,,,,\"0008\",\"用户打开RADF\",,,,\"PI1\",,,,\"0214\",\"中继纸排出传感器滞留卡纸\",,,,,\"PS19Z\"
,,,,,\"0009\",\"RADF盖板打开\",,,,\"PI9\",,,,\"0081\",\"纸未到达纸堆垛输送杆原位传感器S8\"
,,,,,\"000A\",\"用户打开RADF盖板\",,,,\"PI9\",,,,\"0082\",\"纸未到达纸返回轮原位传感器S3\"
,,,,,\"000B\",\"初始滞留卡纸\",,,,\"PI6;PI7;PI8\",,,,\"0B35\",\"中继纸排出盖打开卡纸\",,,,,\"PS24Z\"
,,,,,\"000C\",\"搓纸失败\",,,,,,,,\"0B39\",\"前盖打开卡纸\",,,,,\"S1\"
,,,\"G\",,\"供纸位置:\",,,,,,,,,\"外置鞍式分页器Saddle Finisher-G1\"
,,,,,,,\"1\",\"前置纸盒1(500张)\",,,,,,\"FFff\",\"卡纸检测传感器卡纸类别\",,,,\"相关传感器\"
,,,,,,,\"2\",\"前置纸盒2(500张)\",,,,,,\"1006\",\"装订器装订针卡纸\",,,,\"PI9\"
,,,,,,,\"3\",\"前置纸盒3(500张)\",,,,,,\"1007\",\"电源ON卡纸\",,,,\"PI1;PI10\"
,,,,,,,\"4\",\"前置纸盒4(500张)\",,,,,,\"1008\",\"盖打开卡纸\",,,,\"PI22\'PI23;MS2\"
,,,,,,,\"5\",\"未用\",,,,,,\"1011\",\"入口传感器延迟卡纸\",,,,\"PI1;PI10\"
,,,,,,,\"6\",\"未用\",,,,,,\"1012\",\"对折纸<a name=baidusnap0></a><B style=\'color:black;background-color:#ffff66\'>位置传感器</B>延迟卡纸\",,,,\"PI10\"
,,,,,,,\"7\",\"选购件3500张右侧纸仓(L1)\",,,,,,\"1021\",\"入口传感器滞留卡纸\",,,,\"PI1\"
,,,,,,,\"8\",\"手送纸盘\",,,,,,\"1022\",\"对折纸<B style=\'color:black;background-color:#ffff66\'>位置传感器</B>滞留卡纸\",,,,\"PI10\"
,,,,,,,\"9\",\"双面部件\"
,,,\"HHHHHH\",,\"供纸段软计数器\"
,,,\"IIIII\",,\"纸尺寸\"
,\"显示故障码/报警码历史档案\",,,,,,\"ERR\",,,,,,,,\"5-16T\"
,,,\"Display\",,,\"I/O\",\"Adjust\",,,\"Function\",,,\"Option\",,,\"Test\",,\"Counter\"
,,,,\"\",,,,\"\",,,,,,,\"\"
,,,\"AA\",,\"BBBB\",,\"CCCC\",\"DDDD\",,\"EEEE\",,\"FFff\",,\"G\"
,,,\"AA\",,\"BBBB\",,\"CCCC\",\"DDDD\",,\"EEEE\",,\"FFff\",,\"G\"
,,,\"AA\",,\"BBBB\",,\"CCCC\",\"DDDD\",,\"EEEE\",,\"FFff\",,\"G\"
,,,\"AA\",,\"BBBB\",,\"CCCC\",\"DDDD\",,\"EEEE\",,\"FFff\",,\"G\"
,,,,\"←\",,,\"→\",,,,,,\" /—\",,,,\"OK\"
,,,\"AA\",,\"故障发生的序号1～50,数字大故障发生的时间早\"
,,,\"BBBB\",,\"故障发生的月,日(前2位表示月,后2位表示日)\"
,,,\"CCCC\",,\"故障发生的时间(显示24小时)\"
,,,\"DDDD\",,\"故障恢复的时间(显示24小时)\"
,,,\"EEEE\",,\"故障码(E×××)\"
,,,\"FFff\",,\"故障码(E×××)的详细码\",,,,\"E001,E004,E100,E300,E315,E677,E805等有详细码,无详细码的显示0000\"
,,,\"G\",,\"故障发生的部位(0:主机/主控板;1输稿器;2:分页器;3:CFF;4:读取部分;5:打印部分;6:PDL;7:传真)\"
,\"显示高压单元电压,电流的测定值\",,,,,,,\"HV-STS\",,,,,,,\"5-17T\"
,\"COPIER>DISPLAY>HV-STS>PRIMARY\",,,,,,,\"显示当前鼓电阻检测控制的电流值\",,,,,\"OPC鼓一次充电的电流小于353微安,好鼓;353～485微安鼓尚可使用;大于485微安换鼓\"
,\"COPIER>DISPLAY>HV-STS>TR\",,,,,,,\"显示当前转印辊充电的电流值(微安)\",,,,,\"0:转印电压恒压模式;1:转印电压恒压模式(中等);\"
,,,,,,,,,,,,,\"2:转印电压恒压模式(大);3:转印电压恒压模式(小)\"
,\"COPIER>DISPLAY>HV-STS>BIAS\",,,,,,,\"显示显影DC偏压(单位V)\",,,,,\"DC偏压:0～-650V\"
,\"COPIER>DISPLAY>HV-STS>TR-V\",,,,,,,\"显示转印充电辊表面电位控制\",,,,,\"1500～6000V:转印充电辊系统正常,大于6001V:转印充电辊卡住;\"
,,,,,,,,,,,,,\"小于1499V:转印充电辊漏或转印充电辊故障\"
,\"显示传感器状态\",,,,,,,\"SENSOR\",,,,,,,\"5-17T\"
,\"COPIER>DISPLAY>SENSOR>DOC-SZ\",,,,,,,\"显示原稿尺寸传感器检测到的原稿尺寸\"
,\"显示最新报警-2\",,,,,,,,\"ALARM-2\",,,,,,\"5-18T\"
,,,\"Display\",,,\"I/O\",,\"Adjust\",,\"Function\",,,\"Option\",,,\"Test\",,\"Counter\"
,,,,\"\",,,,\"\",,,,,,,\"\"
,,,\"AA\",,\"BBBB\",,\"CCCC\",\"DDDD\",,\"EEFFFF\",,,\"GGGG\",,\"HHHHHHHH\"
,,,\"AA\",,\"报警码发生的序号1～50,数字大故障发生的时间早\"
,,,\"BBBB\",,\"报警码发生的月,日(前2位表示月,后2位表示日)\"
,,,\"CCCC\",,\"报警码发生的时间(显示24小时)\"
,,,\"DDDD\",,\"报警码恢复的时间(显示24小时)\"
,,,\"EEFFFF\",,\"EE报警码发生的部位,FFFF报警码发生的原因,02扫描部,0002:RADF流动扫描时稿台玻璃有污点;04搓纸/输纸系统,0008:纸仓提升故障;\"
,,,,\"EE\",,,\"FFFF\"
,,,,\"02扫描部\",,,\"0002:DADF流动扫描时稿台玻璃有污点\"
,,,,\"04搓纸/输纸系统\",,,\"0008:纸仓提升故障;\"
,,,,,,,\"0011:纸盒1再进纸\"
,,,,,,,\"0012:纸盒2再进纸\"
,,,,,,,\"0013:纸盒3再进纸\"
,,,,,,,\"0014:纸盒4再进纸\"
,,,,,,,\"0018:纸仓再进纸\"
,,,,\"EE\",,,\"FFFF\"
,,,,\"61装订系统\",,,\"0001未装装订针\"
,,,,\"62鞍式装订系统\",,,\"0001未装装订针\"
,,,,\"65打孔系统\",,,\"0001:打孔废纸孔纸满\"
,,,\"GGGG\",,\"显示详细代码\",,,,,,\"参考R和D控制码\"
,,,\"HHHHHHHH\",,\"报警码发生时的总计数\"
,\"2.2 FEEDER输稿器>DISPLAY显示\",,,,,,,,,,,,,,\"5-19T\"
,\"FEEDER>DISPLAY>FEEDSIZE\",,,,,,,\"显示输稿器(ADF)的原稿尺寸传感器检测到的原稿尺寸\"
,\"4.\",\"调整模式\",,,,,,\"Adjust\",,,,,,,\"5-44T\"
,\"4.1\",\"复印机>调整\",,,,,,\"COPIER>ADIUST>\"
,,,\"Display\",,,\"I/O\",,\"Adjust\",,,\"Function\",,,\"Option\",,,\"Test\",,\"Counter\"
,,,,,,\"BLANK\",,,,,,\"空白调整\"
,,,\"AE\",,,,,,,,,\"AE模式的文字浓度调整\"
,,,\"ADJ-XY\",,,,,,,,,\"图像读取位置调整\"
,,,\"CCD\",,,,,,\"FEED-ADJ\",,,\"标准白板调整\",,,,\"进纸时序调整\"
,,,\"LASER\",,,\"HV-PRI\",,,\"CST-ADJ\",,,\"激光调整\",,,,\"一次带电调整\",,,\"纸盒调整\"
,,,,,,\"HV-TR\",,,,,,\"转印辊高压调整\"
,,,\"DEVELOP\",,,,,,\"MISC\",,,\"显影偏压调整\",,,,,,,\"其他调整\"
,,,,,,,,,,,,,,,,\" \"
,,,\"DENS\",,,,,,,,,\"浓度调整\"
,\"AE自动浓度调整\",,,,,,\"AE调整\",,,,,,,,\"5-45T\"
,\"COPIER>ADJUST>AE>AE-TBL\",,,,,,,\"实时AE模式的文字浓度调整\",,,,,,\"调整范围0～9\",,,\"缺省值4\",,,\"数据大文字浓度加深\"
,\"扫描位置调整\",,,,,,\"ADJ-XY\",,,,,,,,\"5-46T\"
,\"COPIER>ADJUST>ADJ-XY>ADJ-X\",,,,,,,\"副扫描方向图像读取开始位置调整\",,,,,,\"调整范围250～290\",,,\"每步0.1毫米\",,\"数据大移向稿台刻度\"
,\"COPIER>ADJUST>ADJ-XY>ADJ-Y\",,,,,,,\"扫描器图像前沿开始位置调整\",,,,,,\"调整范围100～400\",,,\"每步0.1毫米\",,\"数据大移向前边\"
,\"COPIER>ADJUST>ADJ-XY>ADJ-S\",,,,,,,\"光学扫描原位位置调整(原位传感器PS400)\",,,,,,\"调整范围16～128\",,,\"工厂调整用,每步0.1毫米\"
,\"COPIER>ADJUST>ADJ-XY>ADJ-Y-DF\",,,,,,,\"DADF主扫描方向图像读取开始位置调整\",,,,,,\"调整范围100～400\",,,\"每步0.1毫米\"
,\"COPIER>ADJUST>ADJ-XY>STRD-POS\",,,,,,,\"DADF流动扫描CCD读取位置的调整\",,,,,,\"调整范围0～60\",,,\"每步0.1毫米\"
,\"CCD电信号补偿有关的调整\",,,,,,\"CCD \",,,,,,,,\"5-48T\"
,,,,,,,,\"CCD电信号补偿有关的调整,进行COPIER>FUNCTION>CCD>CCD-ADJ操作后,\"
,,,,,,,,,\"输出图像有问题时,输入维修标签上的值\"
,\"COPIER>ADJUST>CCD>SH-TRGT\",,,,,,,\"进行遮蔽Shading补偿时的白色程度目标值输入\",,,,,,,\"进行遮蔽Shading补偿时\"
,\"COPIER>ADJUST>CCD>SH-RATIO\",,,,,,,\"进行遮蔽Shading补偿时的标准白色纸与标准白板之比率数据值输入\"
,\"COPIER>ADJUST>CCD>EGGN-ST\",,,,,,,\"CCD的顶端放大补正开始位置调整值输入\"
,\"COPIER>ADJUST>CCD>EGGN-END\",,,,,,,\"CCD的顶端放大补正结束位置调整值输入\"
,\"COPIER>ADJUST>CCD>PPR\",,,,,,,\"标准白纸的浓度数据\",,,,\"调整范围0～255\",,,,\"*:维修模式中无该项\",,,\"3-8R\",,\"如有底灰降低设定数\"
,\"COPIER>ADJUST>CCD>PLT\",,,,,,,\"标准白板的浓度数据\",,,,\"调整范围0～255\",,,,\"*:维修模式中无该项\",,,\"3-8R\"
,\"COPIER>ADJUST>CCD>GAIN-E/O\",,,,,,,\"CCD输出的增益调整值输入\",,,,,,,,\"*:维修模式中无该项\",,,\"3-8R\"
,\"COPIER>ADJUST>CCD>OFST-E/O\",,,,,,,\"CCD输出的offset调整值输入\",,,,,,,,\"*:维修模式中无该项\",,,\"3-8R\"
,\"COPIER>ADJUST>CCD>SH-RATIO \",,,,,,,\"CCD光补偿补正时标准白纸和标准白板的白电平比例数据\",,,,,,,,\"*:维修模式中无该项\",,,\"3-8R\"
,\"激光调整\",,,,,,\"LASER\",,,,,,,,\"5-48T\"
,\"COPIER>ADJUST>LASER>PVE-OFST\",,,,,,,\"激光光束位置调整(Ofst)\",,,,,,\"调整范围-600～ 600(23大约1毫米),数据大图像向主扫描方向后面移\"
,\"COPIER>ADJUST>LASER>LA-OFF\",,,,,,,\"非标准纸后沿激光光束OFF位置调整(Ofst)\",,,,,,\"调整范围0～600\"
,\"COPIER>ADJUST>LASER>POWER\",,,,,,,\"非电位控制时的激光电源调整\",,,,,,\"调整范围0～255\"
,\"显影偏压调整\",,,,,,\"DEVELOP\",,,,,,,,\"5-49T\"
,\"COPIER>ADJUST>DEVELOP>DE-BC\",,,,,,,\"图像区域显影偏压DC输出的调整\",,,,,,\"调整范围:0图像浓～255图像淡\",,,,,,\"DC偏压:0～-650V\"
,\"COPIER>ADJUST>DEVELOP>DE-OFST\",,,,,,,\"显影偏压DC输出值的调整OFST\",,,,,,\"调整范围:0图像浓～255图像淡(在缺省值±30内调整)\",,,,,,\"AC偏压:Vpp=810V,Vf=1.8KHz\"
,\"浓度调整\",,,,,,\"DENS\",,,,,,,,\"5-50T\"
,\"COPIER>ADJUST>DENS>DENS-ADJ\",,,,,,,\"复印/打印浓度自动补正的微调整\",,,,,,\"调整范围1～9,缺省值=5\",,,\"数据大在图像高浓度部位拖尾减轻;数据小模糊减轻\"
,\"空白调整\",,,,,,\"BLANK\",,,,,,,,\"5-50T\"
,\"COPIER>ADJUST>BLANK>BLANK-T\",,,,,,,\"图像前端空白宽度调整\",,,,,,\"调整范围-100～100\"
,\"COPIER>ADJUST>BLANK>BLANK-B\",,,,,,,\"图像后端空白宽度调整\",,,,,,\"调整范围-100～100\"
,\"一次带电调整\",,,,,,\"HV-PRI\",,,,,,,,\"5-51T\"
,\"COPIER>ADJUST>HV-PRI>P-DC\",,,,,,,\"图像区域一次充电辊的负DC电压调整\",,,,,,,\"调整范围0～255\",,,\"DC-500～-850\"
,\"COPIER>ADJUST>HV-PRI>P-AC\",,,,,,,\"图像区域一次充电辊的AC电压调整\",,,,,,,\"调整范围0～255\",,,\"AC2.0～2.3KV;Vf=1.8KHz\"
,\"COPIER>ADJUST>HV-PRI>AGS-GANE\",,,,,,,\"鼓电阻检测控制(APVC)增益调整值的调整\",,,,,,,\"调整范围0～255,更换复合电源板时,把复合电源板上的标签值输入\"
,\"COPIER>ADJUST>HV-PRI>AGS-OFST\",,,,,,,\"鼓电阻检测控制(APVC)ofst调整值的输入\",,,,,,,\"调整范围0～255,更换复合电源板时,把复合电源板上的标签值输入\"
,\"COPIER>ADJUST>HV-PRI>OFST1-DC\",,,,,,,\"一次充电辊的负DC电压ofst调整\",,,,,,,\"调整范围0～255\"
,\"COPIER>ADJUST>HV-PRI>OFST1-AC\",,,,,,,\"一次充电辊的AC电压ofst调整\",,,,,,,\"调整范围0～255\"
,\"COPIER>ADJUST>HV-PRI>P-AC2\",,,,,,,\"图像区域的一次充电辊的AC2电压调整\",,,,,,,\"调整范围0～255\"
,\"COPIER>ADJUST>HV-PRI>P-AC3\",,,,,,,\"图像区域的一次充电辊的AC3电压调整\",,,,,,,\"调整范围0～255\"
,\"转印高压调整\",,,,,,\"HV-TR\",,,,,,,,\"5-53T\"
,\"COPIER>ADJUST>HV-TR>TR-N1\",,,,,,,\"转印辊正高压电流的调整\",,,,,\"第1面\",,\"调整范围0～10,更换DC控制板时,输入维修标签上的值\",,,\"单位:微安\"
,\"COPIER>ADJUST>HV-TR>TR-N2\",,,,,,,\"转印辊正高压电流的调整\",,,,,\"第2面\",,\"调整范围0～10,更换DC控制板时,输入维修标签上的值\"
,\"COPIER>ADJUST>HV-TR>TR-OFST\",,,,,,,\"转印辊正高压OFST的调整\",,,,,,,\"调整范围0～255,更换DC控制板时,输入维修标签上的值\"
,\"COPIER>ADJUST>HV-TR>TR-SPP\",,,,,,,\"转印辊正高压电流的调整\",,,,,\"厚纸\",,\"调整范围0～10,更换DC控制板时,输入维修标签上的值\",,,\"对手进纸盘选择厚纸模式时有效\"
,\"进纸时序调整\",,,,\" \",,\"FEED-ADJ\",,,,,,,,\"5-54T\"
,\"COPIER>ADJUST>FEED-ADJ>REGIST\",,,,,,,\"对位离合器ON时序调整\",,,,,,,\"调整范围-600～ 600\",,,\"每步0.1毫米\",,\"数据大对位离合器ON时序延迟\"
,\"COPIER>ADJUST>FEED-ADJ>ADJ-REFE\",,,,,,,\"双面再进纸时横向对位调整\",,,,,,,\"调整范围-100～ 100\",,,\"每步0.1毫米\"
,\"COPIER>ADJUST>FEED-ADJ>ARCH\",,,,,,,\"进纸在对位辊处的拱曲量调整\",,,,,,,\"调整范围-100～ 200\",,,\"每步0.1毫米\",,\"缺省值=80\"
,\"手送纸设置\",,,,,,\"CST-ADJ\",,,,,,,,\"5-54T\"
,\"COPIER>ADJUST>CST-ADJ>MF-A4R\",,,,,,,\"50张手进纸盘纸宽度基本数值设置\",,,,,\"A4R\",,\"调整范围0～1024选择该项目,显示反转后按OK键\"
,\"COPIER>ADJUST>CST-ADJ>MF-A6R\",,,,,,,\"50张手进纸盘纸宽度基本数值设置\",,,,,\"A6R\",,\"调整范围0～1024选择该项目,显示反转后按OK键\"
,\"COPIER>ADJUST>CST-ADJ>MF-A4\",,,,,,,\"50张手进纸盘纸宽度基本数值设置\",,,,,\"A4\",,\"调整范围0～1024选择该项目,显示反转后按OK键\"
,\"定影辊薄膜调整\",,,,,,,\"FIXING\",,,,,,,\"5-55T\"
,\"COPIER>ADJUST>FIXING>FX-FL-TH\",,,,,,,\"厚纸定影辊薄膜速度调整\",,,,,,,\"选择该项目显示反转后按OK键,调整范围-3～ 3,缺省值=0\"
,\"COPIER>ADJUST>FIXING>FX-FL-SP\",,,,,,,\"普通纸定影辊薄膜速度调整\",,,,,,,\"选择该项目显示反转后按OK键,调整范围-3～ 3,缺省值=0\"
,\"其他调整\",,,,,,\"MISC\",,,,,,,,\"5-56T\"
,\"COPIER>ADJUST>MISC>C1-ADJ-Y\",,,,,,,\"前置纸盒1激光主扫描开始位置(图像横向对位)调整\",,,,,,,,\"调整范围-32～ 32,每步0.16毫米\"
,\"COPIER>ADJUST>MISC>C2-ADJ-Y\",,,,,,,\"前置纸盒2激光主扫描开始位置(图像横向对位)调整\",,,,,,,,\"调整范围-32～ 32,每步0.16毫米\"
,\"COPIER>ADJUST>MISC>C3-ADJ-Y\",,,,,,,\"前置纸盒3激光主扫描开始位置(图像横向对位)调整\",,,,,,,,\"调整范围-32～ 32,每步0.16毫米\"
,\"COPIER>ADJUST>MISC>C4-ADJ-Y\",,,,,,,\"前置纸盒4激光主扫描开始位置(图像横向对位)调整\",,,,,,,,\"调整范围-32～ 32,每步0.16毫米\"
,\"COPIER>ADJUST>MISC>MF-ADJ-Y\",,,,,,,\"手进纸盘激光主扫描开始位置(图像横向对位)调整\",,,,,,,,\"调整范围-32～ 32,每步0.16毫米\"
,\"COPIER>ADJUST>MISC>DK-ADJ-Y\",,,,,,,\"侧纸仓(L1)进纸盘激光主扫描开始位置(图像横向对位)调整\",,,,,,,,\"调整范围-32～ 32,每步0.16毫米\"
,\"COPIER>ADJUST>MISC>FRAME-X\",,,,,,,\"激光主扫描速度(横向倍率)调整\",,,,,,,,\"调整范围-50～ 50,每步1%\"
,\"COPIER>ADJUST>MISC>FRAME-Y\",,,,,,,\"副扫描方向扫描速度(纵向倍率)调整\",,,,,,,,\"调整范围-50～ 50,每步1%\"
,\"COPIER>ADJUST>MISC>IMG-DLY\",,,,,,,\"副扫描方向激光扫描开始位置(图像纵向对位)调整\",,,,,,,,\"调整范围-20～ 20,每步0.1毫米\"
,\"4.2\",\"DADF-H1输稿器-H1>调整\",,,,,\"FEEDER>ADIUST>\",,,,,,,,\"5-58T\"
,\"FEEDER>ADIUST>DOCST\",,,,,,,\"DADF-H1输稿时原稿前沿对位调整\",,,,,,,\"调整范围-10～ 10\",,,\"每步0.5毫米\"
,\"FEEDER>ADIUST>LA-SPEED\",,,,,,,\"DADF-H1输稿速度(纵向倍率)调整\",,,,,,,\"调整范围-30～ 30\",,,\"每步0.1%\"
,\"4.3\",\"分页器>调整\",,,,,\"SORTER>ADIUST>\",,,,,\"5-59T\",,,\"外置鞍式分页器Saddle Finisher-G1\"
,\"SORTER>ADIUST>PNCH-HLE\",,,,,,,\"打孔位置(输纸方向)的调整\",,,,,,,\"调整范围-3～ 3\",,,\"每步1毫米\"
,\"SORTER>ADIUST>PNCH-Y\",,,,,,,\"打孔位置(横向方向)的调整\",,,,,,,\"调整范围-5～ 5\"
,\"5.\",\"动作确认模式\",,,,,\"FUNCTION\",,,,,,,,\"5-59T\"
,\"5.1\",\"复印机>动作确认模式\",,,,,\"COPIER>FUNCTION\"
,,,,\"画面右上角表示有关机械动作状态,主要状态有READY(维修/复印动作可以接受);SERVICE(维修模式中动作确认时用)\"
,,,\"Display\",,,\"I/O\",,\"Adjust\",,\"Function\",,,\"Option\",,,\"Test\",,\"Counter\"
,,,\"INSTALL\",,,\"FIXING\",,,\"安装时墨粉搅拌\",,,\"定影辊压力检查\"
,,,\"CCD\",,,\"PANEL\",,,\"CCD光补偿自动补正\",,,\"面板动作检查\"
,,,,,,\"PART-CHK\",,,,,,\"元件负载的动作检查\"
,,,\"DENS\",,,\"CLEAR\",,,\"浓度调整\",,,\"RAM/卡纸记录/出错代码记录的清除\"
,,,,,,\"MISC-R\",,,,,,\"其他调整:读出系统的动作检查\"
,,,\"DPC\",,,\"MISC-P\",,,\"电位传感器\",,,\"其他调整:打印系统的动作检查\"
,,,\"CST\",,,\"SYSTEM\",,,\"纸盒尺寸\",,,\"系统的动作检查\"
,\"新机安装\",,,,,,,\"INSTALL\",,,,,,,\"5-62T\"
,\"COPIER>FUNCTION>INSATLL>TONER-S\",,,,,,,,\"新机安装时墨粉搅拌和向显影器内加粉\",,,,,,\"新机安装时墨粉搅拌大约240秒钟,选择TONER-S,\"
,,,,,,,,,,,,,,,\"显示反转后按OK键,由240递减到0(大约4分钟),按停止键可停止动作\"
,\"COPIER>FUNCTION>INSATLL>STRD-POT\",,,,,,,,\"DADF移动扫描CCD读取位置的自动调整\",,,,,,\"选择STRD-POT,显示反转后按OK键后进行自动调整和停止\"
,,,,,,,,,\"由于COPIER>ADJUST>ADJ-XY>STRD-POS的值已更新,要在维修标签中进行记录\"
,\"COPIER>FUNCTION>INSATLL>CARD\",,,,,,,,\"安装读卡器\",,,,,,\"输入可使用卡的张数,设定范围1～2701,缺省值=1可使用300张卡\"
,,,,,,,,,,,,,,,\"初始化卡名称(ID开始,结束编号);初始化ID码\"
,\"CCD光补偿自动补正\",,,,,,,\"CCD\",,,,,,,\"5-63T\"
,\"COPIER>FUNCTION>CCD>CCD-ADJ\",,,,,,,\"CCD光补偿自动补正的自动调整:\"
,,,,,,,,,,,,,\"1,稿台上放10张标准白纸\"
,,,,,,,,,,,,,\"2,选择COPIER>FUNCTION>CCD>CCD-ADJ \"
,,,,,,,,,,,,,\"3,CCD-ADJ,显示反转后按OK键后进行自动调整\"
,,,,,,,,,,,,,\"4,COPIER>ADJUST>CCD>的整个项目已更新,要在维修标签中进行登记\"
,\"COPIER>FUNCTION>CCD>SHDG-POS\",,,,,,,\"CCD 遮蔽(Shading)补偿位置调整:\",,,,,\"遮蔽(Shading)补偿的标准白板上的位置自动调整的数据,调整范围240～ 320\"
,\"COPIER>FUNCTION>CCD>SH-PS-SET\",,,,,,,\"CCD 遮蔽(Shading)补偿位置设定:\",,,,,\"遮蔽(Shading)补偿的标准白板上的位置自动调整的数据\"
,,,,,,,,,,,,,\"更换稿台玻璃(标准白色板)以后或中间色调中有明显的白色条时要执行该模式\"
,,,,,,,,,,,,,\"执行该模式前要进行COPIER>FUNCTION>CCD>CCD-ADJ 调整\"
,,,,,,,,,,,,,\"1,清洁稿台玻璃\"
,,,,,,,,,,,,,\"2,选择COPIER>FUNCTION>CCD>SH-PS-SET,按OK键 \"
,,,,,,,,,,,,,\"3,按OK执行自动CCD 遮蔽(Shading)补偿位置设定调整,调整后自动停止.\"
,\"COPIER>FUNCTION>CCD>EGGN-POS\",,,,,,,\"CCD的端部放大补正的自动调整\",,,,,\"(仅使用RADF进行流动读出时有效)\"
,,,,,,,,,\"1,打开ADF,\"
,,,,,,,,,\"2,选择该项目按OK键,\"
,,,,,,,,,\"3,自动调整,(大约分钟)调整后自动停止\"
,,,,,,,,,\"(如果显示NG检查:ADF是否打开;移动读出用扫描玻璃安装是否正确;\"
,,,,,,,,,\"玻璃顶端(后面)的灰色放大补正板是否有问题;原稿曝光灯点亮是否正确)\"
,,,,,,,,,\"由于COPIER>ADJUST>CCD>EGGN-ST和EGGN-END的项目已更新,要在维修标签中进行记录\"
,\"自动浓度调整\",,,,,,,\"DENS\",,\"CCD 遮蔽(Shading)补偿位置调整后要按次序值行WHITE-ME;PD-DENS;PD-ME\"
,\"COPIER>FUNCTION>DENS>WHITE-ME\",,,,,,,\"标准白平衡自动浓度修正\",,,,\"1,放标准白纸10张以上到稿台玻璃上\"
,,,,,,,,,,,,\"2,选择COPIER>FUNCTION>DENS>WHITE-ME,显示反转后按OK键\"
,,,,,,,,,,,,\"3,扫描灯自动扫描一次后机器自动停止\"
,\"COPIER>FUNCTION>DENS>PD-DENS\",,,,,,,\"打印用于文本模式测试样板\",,,,\"打印出用于文本模式自动浓度调整(PD-ME)的17级灰度测试样板\"
,,,,,,,,,,,,\"选择PD-DENS显示反转后按OK键,从纸盒2进纸打印出17级灰度测试样板\"
,\"COPIER>FUNCTION>DENS>PD-ME\",,,,,,,\"文本模式自动浓度调整\",,,,\"1,把17级灰度测试样板的最浅一级灰度面向下放在稿台玻璃上左边靠刻度标尺位置\"
,,,,,,,,,,,,\"2,选择PD-ME显示反转后按OK键,扫描灯点亮,息灭13次,自动进行扫描\"
,,,,,,,,,,,,\"如果显示\\\"OK\\\"调整结束;如果显示\\\"NG\\\"见第3章\\\"标准和调整\"
,\"OPC鼓电位控制APVC\",,,,,,,\"DPC\",,,,,,,\"5-69T\"
,\"COPIER>FUNCTION>DPC>D-GAMMA\",,,,,,,\"鼓电阻检测控制(APVC)\",,,,\"更换鼓后或使用旧鼓或复印浓度调整无结果时用\"
,,,,,,,,,,,,\"缺省值0:正常模式;1:执行鼓电阻测量(APVC)控制,选择D-GAMMA显示反转后按OK键\"
,,,,,,,,,,,,\"打印出1张黑色样板,在COPIER>DISPLAY>HV-STS>PRIMARYK中\"
,,,,,,,,,,,,\"可以显示出当前鼓电阻测量控制(APVC)的一次鼓充电辊电流结果\"
,\"纸盒尺寸调整\",,,,,,,\"CST\",,,,,,,\"5-69T\"
,\"COPIER>FUNCTION>CST>MF-A4R\",,,,,,,\"手进纸宽度设置\",,,,\"1,在手进纸盘上放入A4R尺寸纸,侧板放在A4R宽度\"
,,,,,,,,,,,,\"2,选择MF-A4R显示反转后按OK键,自动将MF-A4R的宽度数据(210毫米)存储\"
,\"COPIER>FUNCTION>CST>MF-A6R\",,,,,,,\"手进纸宽度设置\",,,,\"1,在手进纸盘上放入A6R尺寸纸,侧板放在A6R宽度;\"
,,,,,,,,,,,,\"2,选择MF-A6R显示反转后按OK键,自动将MF-A6R的宽度数据(105毫米)存储\"
,\"COPIER>FUNCTION>CST>MF-A4\",,,,,,,\"手进纸宽度设置\",,,,\"1,在手进纸盘上放入A4尺寸纸,侧板放在A4宽度;\"
,,,,,,,,,,,,\"2,选择MF-A4显示反转后按OK键,自动将MF-A4的宽度数据(297毫米)存储\"
,\"定影辊压力调整\",,,,,,,\"FIXING\",,,,,,,\"5-67T\"
,\"COPIER>FUNCTION>FIXING>NIP-CHK\",,,,,,,\"定影辊压力检查\",,,,\"1,打印A4全黑样板,复印20张,将20张复印副本面向下放入手送纸盘.\"
,,,,,,,,,,,,\"2,选择该项目显示反转后按OK键,手送纸盘输入的纸夹在定影辊位置停留一下,20秒钟后输出.\"
,,,,,,,,,,,,\"3,检查纸张两边a和c的10毫米处的尺寸,a-c=0.5毫米以下;纸张中间的尺寸标准值=7.8±0.5毫米\"
,\"面板动作检查\",,,,,,,\"PANLE\",,,,,,,\"5-71T\"
,\"COPIER>FUNCTION>PANLE>LCD-CHK\",,,,,,,\"液晶显示屏漏点检查\",,,,\"选择LCD-CHK显示反转后按OK键,液晶显示屏反复显示全白/全黑的图象,按停止键检查停止\"
,\"COPIER>FUNCTION>PANLE>LED-CHK\",,,,,,,\"发光二极管LED漏点检查\",,,,\"选择LED-CHK显示反转后按OK键,面板发光二极管LED依次点亮,停止检查用LED-OFF\"
,\"COPIER>FUNCTION>PANLE>LED-OFF\",,,,,,,\"发光二极管LED漏点检查停止\",,,,\"选择LED-OFF显示反转后按OK键,停止面板发光二极管LED依次点亮的检查\"
,\"COPIER>FUNCTION>PANLE>KEY-CHK\",,,,,,,\"面板按键检查\",,,,\"选择KEY-CHK,显示反转后按OK键,\"
,,,,,,,,,,,,\"按要检查的键,画面显示出该键对应的文字,再次选择KEY-CHK退出面板按键检查\"
,,,,,,,,,,,,\"按键名称\",,\"键对应的文字\",,\"按键名称\",,\"键对应的文字\"
,,,,,,,,,,,,\"计数器确认\",,\"BILL\",,\"ID键\",,\"ID\"
,,,,,,,,,,,,\"复印键\",,\"COOPY\",,\"用户模式键\",,\"USER\"
,,,,,,,,,,,,\"传真键\",,\"FAX\",,\"复印键\",,\"START\"
,,,,,,,,,,,,\"信箱键\",,\"PB\",,\"停止键\",,\"STOP\"
,,,,,,,,,,,,\"扩展键\",,\"OTHER\",,\"复位键\",,\"RESET\"
,,,,,,,,,,,,\"0～9,#,*键\",,\"0～9,#,*\",,\"插入键\",,\"INTERRUP\"
,,,,,,,,,,,,\"清除键\",,\"CLEAR\",,\"帮助键\",,\" \"
,\"COPIER>FUNCTION>PANEL>TOUCHCHKEY\",,,,,,,\"液晶显示屏触摸键与LCD坐标位置相吻合\",,,,,,\"选择TOUCHCHKEY,显示反转后按OK键,轮流按液晶显示屏上出现9个\\\" \\\"\"
,,,,,,,,,,,,,,\"调整完毕后再选择TOUCHCHKEY结束操作\"
,\"元件负载的动作检查\",,,,,,,\"PART-CHK\",,,,,,,\"5-72T\"
,\"COPIER>FUNCTION>PART-CHA>CL\",,,,,,,\"选择要动作的离合器\",,,,,,\"选择CL后键入要动作的离合器的代码号再按OK键,该代码号的离合器被选中\"
,,,,,,,,,,,,,,\"代码号\",\"离合器\"
,,,,,,,,,,,,,,\"1\",\"垂直纸道离合器CL1\"
,,,,,,,,,,,,,,\"2\",\"手送纸离合器CL2\"
,,,,,,,,,,,,,,\"3\",\"显影离合器CL3\"
,,,,,,,,,,,,,,\"4\",\"选购件纸盒工作台W1的垂直纸道离合器CL1C;\"
,,,,,,,,,,,,,,\"5\",\"选购件3500张右侧纸仓(L1)输纸离合器CL1D\"
,,,,,,,,,,,,,,\"6\",\"选购件3500张右侧纸仓(L1)搓纸离合器CL2D\"
,\"COPIER>FUNCTION>PART-CHA>CL-ON\",,,,,,,\"被选的离合器启动动作\",,,,,,\"选择该项目后按OK键,被选离合器ON→10秒OFF,→ON→10秒OFF,→ON→OFF\"
,\"COPIER>FUNCTION>PART-CHA>MTR\",,,,,,,\"选择要动作的电机\",,,,,,\"选择该项目后键入要动作的电机的代码号再按OK键,该代码号的电机被选中\"
,,,,,,,,\"代码号\",\"对应的电机\",,,,,,,,\"代码号\",\"对应的电机\"
,,,,,,,,\"1\",\"主电机M1\",,,,,,,,\"8\",\"横向对位电机M3\"
,,,,,,,,\"2\",\"定影电机M4\",,,,,,,,\"9\",\"对位辊电机M9\"
,,,,,,,,\"3\",\"搓纸电机M2\",,,,,,,,\"10\",\"激光扫描电机M10\"
,,,,,,,,\"4\",\"双面部件电机M6\",,,,,,,,\"11\",\"选购件纸盒工作台W1,主电机M1C\"
,,,,,,,,\"5\",\"排纸电机M5\",,,,,,,,\"12\",\"选购件纸盒工作台W1,搓纸电机M2C\"
,,,,,,,,\"6\",\"向No.3接纸盘(外置接纸托盘)排纸电机M8B\",,,,,,,,\"13\",\"选购件3500张右侧纸仓(L1),主电机M1D\"
,,,,,,,,,\"Finisher-J1,纸输送电机M7Z\",,,,,,,,\"14\",\"选购件3500张右侧纸仓(L1),升纸电机M2D\"
,,,,,,,,\"7\",\"向No.2接纸盘(内置2路接纸托盘的上层)排纸电机M7B\"
,\"COPIER>FUNCTION>PART-CHA>MTR-ON\",,,,,,,,\"被选的电机启动动作\",,,,\"选择该项目后按OK键,被选电机ON 20秒→OFF;粉仓电机,\"
,,,,,,,,,,,,,\"双面横向对位电机10秒ON→OFF;选购件移动托盘电机在前和后边的HP原位停止\"
,\"COPIER>FUNCTION>PART-CHA>SL\",,,,,,,\"选择要动作的电磁铁\",,,,,\"选择该项目后键入要动作的电磁铁的代码号再按OK键,该代码号的电磁铁被选中\"
,,,,,,,,\"代码号\",\"对应的电磁铁\",,,,,,,\"代码号\",\"对应的电磁铁\"
,,,,,,,,\"1\",\"搓纸轮下降电磁铁SL1\",,,,,,,\"5\",\"未用\"
,,,,,,,,\"2\",\"选购件纸盒工作台W1,排纸电磁铁SL3B\",,,,,,,\"6\",\"选购件纸盒工作台W1,搓纸轮下降电磁铁SL1C\"
,,,,,,,,\"3\",\"一次充电辊清洁电磁铁SL6\",,,,,,,\"7\",\"选购件3500张右侧纸仓(L1),搓纸轮释放电磁铁SL1D\"
,,,,,,,,\"4\",\"手送纸搓纸轮释放电磁铁SL5\",,,,,,,\"8\",\"选购件3500张右侧纸仓(L1),纸仓打开电磁铁SL2D\"
,\"COPIER>FUNCTION>PART-CHA>SL-ON\",,,,,,,\"被选的电磁铁启动动作\",,,,,,\"选择该项目后按OK键,被选的电磁铁ON 10秒OFF→ON 10秒OFF →ON →OFF\"
,\"RAM/卡纸记录/出错代码记录的清除\",,,,,,,\"CLEAR\",,,,,,,\"5-75T\"
,\"COPIER>FUNCTION>CLEAR>ERR\",,,,,,,\"清除出错代码\",,,,,\"选择ERR,显示反转后按OK键;OFF/ON主电源开关,清除E000～E003;E007;E032;E717;E719\"
,\"COPIER>FUNCTION>CLEAR>DC-CON\",,,,,,,\"清除DC控制板的RAM\",,,,,\"选择DC-CON,显示反转后按OK键;OFF/ON主电源开关\"
,\"COPIER>FUNCTION>CLEAR>R-CON\",,,,,,,\"清除读出控制板的RAM\",,,,,\"选择R-CON,显示反转后按OK键;OFF/ON主电源开关\"
,\"COPIER>FUNCTION>CLEAR>SERVICE\",,,,,,,\"清除维修模式的后备数据\",,,,,\"选择SERVICE,显示反转后按OK键;OFF/ON主电源开关\"
,\"COPIER>FUNCTION>CLEAR>JAN-HIST\",,,,,,,\"清除卡纸记录\",,,,,\"选择JAM-HIST,显示反转后按OK键;OFF/ON主电源开关\"
,\"COPIER>FUNCTION>CLEAR>ERR-HIST\",,,,,,,\"清除出错记录\",,,,,\"选择ERR-HIST,显示反转后按OK键;OFF/ON主电源开关\"
,\"COPIER>FUNCTION>CLEAR>E345-CLR\",,,,,,,\"清除E345\",,,,,\"选择E345-CLR,显示反转后按OK键;OFF/ON主电源开关,清除E345\"
,\"COPIER>FUNCTION>CLEAR>E355-CLR\",,,,,,,\"清除E355\",,,,,\"选择E355-CLR,显示反转后按OK键;OFF/ON主电源开关,清除E355\"
,\"COPIER>FUNCTION>CLEAR>PWD-CLR\",,,,,,,\"用户模式下设定的[系统管理]密码的清除\",,,,,,\"选择PWD-CLR,显示反转后按OK键;OFF/ON主电源开关\"
,\"COPIER>FUNCTION>CLEAR>ADRS-BK\",,,,,,,\"清除书本数据地址\",,,,,\"选择ADRS-BK,显示反转后按OK键,OFF/ON主电源开关\"
,\"COPIER>FUNCTION>CLEAR>CNT-MCON\",,,,,,,\"主控板计数的维修计数器的清除\",,,,,\"选择CNT-MCON,显示反转后按OK键;OFF/ON主电源开关\"
,\"COPIER>FUNCTION>CLEAR>CNT-DCON\",,,,,,,\"DC控制板计数的维修计数器的清除\",,,,,\"选择CNT-DCON,显示反转后按OK键;OFF/ON主电源开关\"
,\"COPIER>FUNCTION>CLEAR>MMI\",,,,,,,\"用户模式下设定的[规格设定/密码模式/部门ID/模式记忆等]后备数据的清除\"
,,,,,,,,,,,,,,\"选择MMI,显示反转后按OK键;OFF/ON主电源开关\"
,\"COPIER>FUNCTION>CLEAR>CARD\",,,,,,,\"清除卡的ID有关数据\",,,,,\"选择CARD,显示反转后按OK键,OFF/ON主电源开关\"
,\"COPIER>FUNCTION>CLEAR>ALARM\",,,,,,,\"清除报警记录\",,,,,\"选择ALARM,显示反转后按OK键,OFF/ON主电源开关\"
,\"读出系统的扫描灯动作检查\",,,,,,,\"MISC-R\",,\"原稿扫描灯动作确认\",,,,,\"5-77T\"
,\"COPIER>FUNCTION>MISC-R>SCANLAMP\",,,,,,,\"原稿扫描曝光灯ON/OFF检查\",,,,,\"选择SCANLAMP,显示反转后按OK键,\"
,,,,,,,,,,,,,\"原稿扫描曝光灯点亮大约1秒钟;按停止键扫描曝光灯OFF\"
,\"其他调整:打印系统的动作检查\",,,,,,,\"MISC-P\",,,,,,,\"5-78T\"
,\"COPIER>FUNCTION>MISC-P>P-PRINT\",,,,,,,\"打印维修模式一览表\",,,,,\"选择P-PRINT,显示反转后按OK键,打印出维修模清单\"
,\"COPIER>FUNCTION>MISC-P>KEY-HIST\",,,,,,,\"打印操作面板的按键输入记录\",,,,,\"选择KEY-HIST,显示反转后按OK键,打印出操作面板的按键输入记录\"
,,,,,,,,,,,,,\"操作面板的按键输入记录\",,,,\"AA:AA BBBB CCCC XXXXXXXX\"
,,,,,,,,,,,,,\"AA\",,,,\"如果是数字\",,\"按键次数\"
,,,,,,,,,,,,,,,,,\"HARD\",,\"硬键\"
,,,,,,,,,,,,,,,,,\"SOFT\",,\"软键\"
,,,,,,,,,,,,,,,,,\"ONET\",,\"触摸键\"
,,,,,,,,,,,,,\"CC\",\"按下的键\",,,\"RESET\",,\"复位键\"
,,,,,,,,,,,,,,,,,\"START\",,\"复印键\"
,,,,,,,,,,,,,,,,,\"GRIDE\",,\"帮助键\"
,,,,,,,,,,,,,,,,,\"USER MODE\",,\"用户方式(星号\\\"*\\\")键\"
,,,,,,,,,,,,,,,,,\"FNC-COPY\",,\"复印扩展键\"
,,,,,,,,,,,,,,,,,\"FCN-FAX\",,\"传真扩展键\"
,,,,,,,,,,,,,,,,,\"POWER-MIMI\",,\"操作面板上的电源开关键\"
,,,,,,,,,,,,,\"XXXXXXXX\",,,,\"起作用值\"
,\"COPIER>FUNCTION>MISC-P>HIST-PRT\",,,,,,,\"打印卡纸记录/出错代码记录\",,,,,\"选择HIST-PRT,显示反转后按OK键,打印出维修模式的卡纸记录/出错代码记录\"
,\"COPIER>FUNCTION>MISC-P>USER-PRT\",,,,,,,\"打印用户模式一览表\",,,,,\"选择USER-PRT,显示反转后按OK键,打印出用户模式一览表\"
,\"COPIER>FUNCTION>MISC-P>C1-ADJ-Y\",,,,,,,\"纸盒1水平对位自动调整\",,,,,\"选择C1-ADJ-Y显示反转后按OK键,从纸盒1输纸打印出一张半色调PG图像\"
,,,,,,,,,,,,,\"同时水平对位传感器测试移动量,并把数据存入内存储器\"
,\"COPIER>FUNCTION>MISC-P>C2-ADJ-Y\",,,,,,,\"纸盒2水平对位自动调整\",,,,,\"选择C2-ADJ-Y显示反转后按OK键,从纸盒2输纸打印出一张半色调PG图像\"
,,,,,,,,,,,,,\"同时水平对位传感器测试移动量,并把数据存入内存储器\"
,\"COPIER>FUNCTION>MISC-P>C3-ADJ-Y\",,,,,,,\"纸盒3水平对位自动调整\",,,,,\"选择C3-ADJ-Y显示反转后按OK键,从纸盒3输纸打印出一张半色调PG图像\"
,,,,,,,,,,,,,\"同时水平对位传感器测试移动量,并把数据存入内存储器\"
,\"COPIER>FUNCTION>MISC-P>C4-ADJ-Y\",,,,,,,\"纸盒4水平对位自动调整\",,,,,\"选择C4-ADJ-Y显示反转后按OK键,从纸盒4输纸打印出一张半色调PG图像\"
,,,,,,,,,,,,,\"同时水平对位传感器测试移动量,并把数据存入内存储器\"
,\"COPIER>FUNCTION>MISC-P>MF-ADJ-Y\",,,,,,,\"手进纸盒水平对位自动调整\",,,,,\"选择MF-ADJ-Y显示反转后按OK键,从手进纸盒输纸打印出一张半色调PG图像\"
,,,,,,,,,,,,,\"同时水平对位传感器测试移动量,并把数据存入内存储器\"
,\"COPIER>FUNCTION>MISC-P>DK-ADJ-Y\",,,,,,,\"侧纸仓(L1)水平对位自动调整\",,,,,\"选择DK-ADJ-Y显示反转后按OK键,从侧纸仓(L1)输纸打印出一张半色调PG图像\"
,,,,,,,,,,,,,\"同时水平对位传感器测试移动量,并把数据存入内存储器\"
,\"COPIER>FUNCTION>MISC-P>LBL-PRNT\",,,,,,,\"打印出一张维修模式一览表\",,,,,\"将纸放入手进纸盒,选择LBL-PRNT显示反转后按OK键,打印出一张维修模式一览表\"
,\"COPIER>FUNCTION>MISC-P>PER-EXP\",,,,,,,\"预曝光灯LED点亮检查\",,,,,\"选择PER-EXP,显示反转后按OK键,预曝光灯LED点亮大约3秒后熄灭.\"
,\"系统有关的动作检查\",,,,,,,\"SYSTER\",,,,,,,\"5-81T\"
,\"COPIER>FUNCTION>SYSTER>D0ENLOAD\",,,,,,,\"系统程序下载时的有关动作检查\",,,,,\"1,关闭复印机和电脑的电源开关\"
,,,,,,,,,,,,,\"2,取下复印机与网络相关的电缆线\"
,,,,,,,,,,,,,\"3,用双向并行口电缆线将复印机与电脑连接\"
,,,,,,,,,,,,,\"4,打开电脑和复印机的电源开关\"
,,,,,,,,,,,,,\"5,选择DWNLRD,显示反转后按OK键,通过维修支持工具进行下载数据,\"
,,,,,,,,,,,,,\" 下载完成后关闭复印机和电脑的电源开关\"
,\"COPIER>FUNCTION>SYSTER>CHK-TYPE\",,,,,,,\"选择HD-CHECK的分割号\",,,,,\"选择CHK-TYPE,显示反转后按OK键,键入分割号\"
,,,,,,,,,,,,,\"(0:检查和恢复整个HDDY有缺陷的部分;1:图像存储区;3:PDL有关文件存储区;\"
,,,,,,,,,,,,,\"4:固化软件存储区)一般文件如下:用户设定数据,记录数据,PDLspool数据,图像数据\"
,\"COPIER>FUNCTION>SYSTER>HD-CHECK\",,,,,,,\"执行CHK-TYPE选择的分割号\",,,,,\"选择HD-CHECK,显示反转后按OK键,机器指示结果(1:OK,2:NG硬件,3:NG软件);\"
,,,,,,,,,,,,,\"恢复传感器/交替扇区\"
,\"COPIER>FUNCTION>SYSTER>HD-CLEAR\",,,,,,,\"执行CHK-TYPE选择的分割号初始化\",,,,,\"选择HD-CHECK,显示反转后按OK键,执行CHK-TYPE选择的分割号的初始化,如果选择0\"
,,,,,,,,,,,,,\"或4该执行无效;如果选择1存储在SRAM区的图像数据或一般文件存储区被初始化\"
,\"6\",\"机器功能设定模式\",,,,,,\"选项 OPTION\",,,,,,,\"5-82T\"
,\"6.1\",\"复印机>选项\",,,,,,\"COPIER>OPTION>\"
,,,\"Display\",,,\"I/O\",,\"Adjust\",,\"Function\",,,\"Option\",,,\"Test\",,\"Counter\"
,,,\"BODY\",,,\"与主机有关的功能设定模式\"
,,,\"USER\",,,\"与用户模式有关的功能设定模式\"
,,,\"CST\",,,\"与纸盒有关的功能设定模式\"
,,,\"ACC\",,,\"与选购件有关的功能设定模式\"
,,,\"INT-FACE\",,,\"控制器接口的设定\"
,\"与主机有关的功能设定模式\",,,,,,,\"COPIER>OPTION>BODY\",,,,,,,\"5-80T\"
,\"COPIER>OPTION>BODY>MODEL-SZ\",,,,,,,\"规格/固定倍率/尺寸模式设定\",,,,,\"0:AB(6R5E) ;1:英制(5R4E) ;2:A(3R3E) ;3:AB/英制(6R5E)\"
,\"COPIER>OPTION>BODY>FIX-CLN\",,,,,,,\"定影清洁设定\",,,,,\"0:OFF(缺省值) ; 1:每500张清洁一次,温度控制在225度,空转60秒; \"
,,,,,,,,,,,,,\"2:每200张清洁一次,温度控制在225度,空转60秒\"
,,,,,,,,,,,,,\"3:每100张清洁一次,温度控制在225度,空转60秒;\"
,\"COPIER>OPTION>BODY>FIX-TEMP\",,,,,,,\"定影温度设修改选择\",,,,,\"0:禁止(缺省值)\"
,,,,,,,,,,,,,\"1:保持定影温度恒定在目标温度-10度\"
,,,,,,,,,,,,,\"2:保持定影温度恒定在目标温度-6度\"
,,,,,,,,,,,,,\"3:保持定影温度恒定在目标温度-3度\"
,,,,,,,,,,,,,\"4:保持定影温度恒定在目标温度 3度\"
,,,,,,,,,,,,,\"5:保持定影温度恒定在目标温度 6度\"
,,,,,,,,,,,,,\"6:保持定影温度恒定在目标温度 10度\"
,,,,,,,,,,,,,\"7:保持定影温度恒定在目标温度 15度\"
,\"COPIER>OPTION>BODY>HUM-SW\",,,,,,,\"环境传感器ON/OFF\",,,,,\"0:环境传感器自动控制;1:固定模式,高湿度;2:固定模式,中湿度;3固定模式,低湿度\"
,\"COPIER>OPTION>BODY>SCANSLCT\",,,,,,,\"DADF的原稿尺寸检测的ON/OFF\",,,,,\"0:OFF(缺省值) ;1:ON 根据原稿尺寸决定扫描尺寸\"
,\"COPIER>OPTION>BODY>TRANS-SW\",,,,,,,\"大尺寸纸时转印辊电流输出控制\",,,,,\"0:正常(自动模式);\"
,,,,,,,,,,,,,\"1:恒定电压控制(手动模式),选择1后还要在COPIER>ADJUST>HV-TR>TR-N1中设定\"
,\"COPIER>OPTION>BODY>PRIAC\",,,,,,,\"新鼓充电改变\",,,,,\"0:正常,缺省值;1:鼓电流增加(新鼓复印到2000张时发生白点的图像时用)\"
,,,,,,,,,,,,,\"还要把下例的设定清除(1→0),新鼓按装后APC被执行;\"
,,,,,,,,,,,,,\"在维修模式中COPIER>FUNCTION>DPC>D-GAMMA被执行;在维修模式中该设定被改变;\"
,\"COPIER>OPTION>BODY>SENS-CNF\",,,,,,,\"原稿传感器设定\",,,,,\"0:AB系列,缺省值;1:英寸系列;2:A系列\"
,\"COPIER>OPTION>BODY>CONFIG\",,,,,,,\"硬盘使用地,国家,语言,纸尺寸设定\",,,,,\"XXYYZZAA\",,\"按照COPIER>DISPLAY>USER>LANGUAGE的方法显示,\"
,,,,,,,,,,,,,\"XX:国家码(JP);YY:语言码(JA);ZZ:(缺省值=00)使用地;AA:(缺省值=00)纸尺寸系列\"
,\"COPIER>OPTION>BODY>SHARP\",,,,,,,\"图像清晰度电平设定\",,,,,\"设定范围:1～5 ;缺省值=3,数值大清晰度高(焦距增大)\"
,\"COPIER>OPTION>BODY>LAPC-SW\",,,,,,,\"激光自动功率控制(APC)补正的设定\",,,,,\"0:0N(10分钟无操作进行前旋转APC);1:0N(60分钟无操作进行前旋转APC),缺省值\"
,,,,,,,,,,,,,\"2:0N(120分钟无操作进行前旋转APC);3:只有前旋转APC为OFF ;4:OFF\"
,\"COPIER>OPTION>BODY>COTDPC-D\",,,,,,,\"工厂调整用\",,,,,\"设定范围:0～3 ;缺省值=0\"
,\"COPIER>OPTION>BODY>DF-BLINE\",,,,,,,\"移动扫描时的黑线减弱(边缘增强OFF)模式的ON/OFF\",,,,,,,,\"0:OFF(缺省值) ;1:ON 黑线减弱,打印图像的边缘柔和化\"
,\"COPIER>OPTION>BODY>FIX-SMR\",,,,,,,\"环境湿度非常高时工作设定\",,,,,\"0:正常模式(缺省值); \"
,,,,,,,,,,,,,\"1:工作在高湿度,(激光光亮减少50V);定影薄膜速度变为539～535毫米/秒;\"
,,,,,,,,,,,,,\" 定影/搬送速度B4从每分钟14变到10张,B5从每分钟28变到15张\"
,,,,,,,,,,,,,\" LGL从每分钟14变到10张,A4R从每分钟18变到10张\"
,\"COPIER>OPTION>BODY>DEBRL-FN\",,,,,,,\"减少卷曲风扇ON/OFF设定\",,,,,\"0:OFF缺省值;1:ON,在图像边缘传感器ON后减少卷曲风扇ON30秒\"
,\"COPIER>OPTION>BODY>TR-CLN\",,,,,,,\"转印辊清洁偏压增强模式设定\",,,,,\"0:OFF缺省值;1:ON,单面打印纸张转印输出之间设定转印辊清洁偏压\"
,\"COPIER>OPTION>BODY>FAN-EXTN\",,,,,,,\"工作结束后风扇继续工作的设定\",,,,,\"0:正常模式(缺省值);1:高时工作设定\"
,\"与用户模式有关的功能设定模式\",,,,,,,\"COPIER>OPTION>USER>\",,,,,,,\"5-86T\"
,\"COPIER>OPTION>USER>COPY-LIM\",,,,,,,\"复印张数上限设定\",,,,,\"范围1～999\",,\"缺省值=999\"
,\"COPIER>OPTION>USER>SLEEP\",,,,,,,\"睡眠功能设定\",,,,,\"0:ON 缺省值\",,\"1:OFF\"
,\"COPIER>OPTION>USER>SIZE-DET\",,,,,,,\"原稿尺寸检测功能的ON/OFF设定\",,,,,\"0:ON 缺省值\",,\"1:OFF\",,,\"设定后要将主电源开关OFF后再ON\"
,\"COPIER>OPTION>USER>COUNTER1\",,,,,,,\"操作面板软计数器1的类型显示\",,,,,\"设定数,101:总计数1[缺省值,不能改变]\"
,\"COPIER>OPTION>USER>COUNTER2\",,,,,,,\"操作面板软计数器2的类型设定\",,,,,\"设定数:000～804[缺省值000(100V机型),103(120/230V机型)]\",,,,,,,,,\"可以改变设定\"
,\"COPIER>OPTION>USER>COUNTER3\",,,,,,,\"操作面板软计数器3的类型设定\",,,,,\"设定数:000～804[缺省值000(100V机型),201(120/230V机型)]\",,,,,,,,,\"可以改变设定\"
,\"COPIER>OPTION>USER>COUNTER4\",,,,,,,\"操作面板软计数器4的类型设定\",,,,,\"设定数:000～804[缺省值000(100V机型),203(120/230V机型)]\",,,,,,,,,\"可以改变设定\"
,\"COPIER>OPTION>USER>COUNTER5\",,,,,,,\"操作面板软计数器5的类型设定\",,,,,\"设定数:000～804[缺省值000)]\",,,,,,,,,\"可以改变设定\"
,\"COPIER>OPTION>USER>COUNTER6\",,,,,,,\"操作面板软计数器6的类型设定\",,,,,\"设定数:000～804[缺省值000)]\",,,,,,,,,\"可以改变设定\"
,,,,,,,,\"注:见下一张的软计数器号码表\"
,\"COPIER>OPTION>USER>DATE-DSP\",,,,,,\"日期/时间表示型式设定\",,,,,,\"0:YY/MM/DD缺省值\",,,\"1:DD/MM/YY\",,,\"2:MM/DD/YY\"
,\"COPIER>OPTION>USER>MB-CCV\",,,,,,\"信箱控制卡IV(CC-IV)使用者限制\",,,,,,\"0:遥控时不受卡的限制,均可操作和打印,遥控不计费\"
,,,,,,,,,,,,,\"1:遥控时不受卡的限制,均可操作,可输入打印工作,\"
,,,,,,,,,,,,,\" 但无控制卡不能打印输出(有卡可打印输出,但要计费)缺省值\"
,,,,,,,,,,,,,\"2:遥控工作不能接受,也不能输入打印工作.\"
,\"COPIER>OPTION>USER>B4-LCNT\",,,,,,\"软计数器1～6,用B4纸时(L)/(S)计数设定\",,,,,,\"0:小尺寸(S)计数(缺省值);1:大尺寸(L)计数\"
,\"COPIER>OPTION>USER>TRY-STP\",,,,,,\"装订/混载限制而中断打印的禁止\",,,,,,\"0:正常模式[缺省值](因份数/混载限制中断打印);\"
,,,,,,,,,,,,,\"1:高度传感器ON(纸张满载)时中断打印\"
,\"COPIER>OPTION>USER>MF-LG-ST\",,,,,,\"手送纸盘纸尺寸加长键的设定(显示该键)\",,,,,,\"0:正常模式(缺省值);1:纸尺寸可加长到(630毫米)模式(显示该键)\"
,\"COPIER>OPTION>USER>SPECK-DP\",,,,,,\"移动扫描读出时检测到异物的警告显示\",,,,,,\"0:不显示(缺省值);1:显示\"
,\"COPIER>OPTION>USER>CNT-DISP\",,,,,,\"按计数器确认键时的编号的显示/不显示\",,,,,,\"0:不显示(缺省值);1:显示\"
,\"COPIER>OPTION>USER>PH-D-SEL\",,,,,,\"照片模式打印的线数选择\",,,,,,\"0:141线(缺省值);1:134线\"
,\"COPIER>OPTION>USER>COPY-JOB\",,,,,,\"使用控制卡或投币器时的复印工作预约设定\",,,,,,\"0:有复印工作预约(缺省值);1:无复印工作预约\"
,\"COPIER>OPTION>USER>OP-SZ-DT\",,,,,,\"书本模时的原稿尺寸检测的ON/OFF\",,,,,,\"0:OFF(缺省值)从面板输入原稿尺寸;1:ON(自动检测原稿尺寸)\"
,\"COPIER>OPTION>USER>NW-SCAN\",,,,,,\"网络扫描ON/OFF设定\",,,,,,\"0:OFF(缺省值) ;1:ON 网络扫描可以\"
,\"与纸盒有关的功能设定模式\",,,,,,,\"COPIER>OPTION>CST>\",,,,,,,\"5-92T\",,\"注:U1-NAME.万用纸盒U1的名称\"
,\"COPIER>OPTION>CST>U1-NAME\",,,,,,\"纸盒尺寸拨盘选在U1时,纸名称的ON/OFF\",,,,,,\"0:OFF(缺省值),液晶显示U1;1:ON时,液晶显示(CST-U1)所指定的纸张名称\"
,\"COPIER>OPTION>CST>U2-NAME\",,,,,,\"纸盒尺寸拨盘选在U2时,纸名称的ON/OFF\",,,,,,\"0:OFF(缺省值),液晶显示U1;1:ON时,液晶显示(CST-U2)所指定的纸张名称\"
,\"COPIER>OPTION>CST>U3-NAME\",,,,,,\"纸盒尺寸拨盘选在U3时,纸名称的ON/OFF\",,,,,,\"0:OFF(缺省值),液晶显示U1;1:ON时,液晶显示(CST-U3)所指定的纸张名称\"
,\"COPIER>OPTION>CST>U4-NAME\",,,,,,\"纸盒尺寸拨盘选在U4时,纸名称的ON/OFF\",,,,,,\"0:OFF(缺省值),液晶显示U1;1:ON时,液晶显示(CST-U4)所指定的纸张名称\"
,\"COPIER>OPTION>CST>U5-NAME\",,,,,,\"纸盒尺寸拨盘选在U5时,纸名称的ON/OFF\",,,,,,\"0:OFF(缺省值),液晶显示U1;1:ON时,液晶显示(CST-U5)所指定的纸张名称\"
,\"COPIER>OPTION>CST>U6-NAME\",,,,,,\"纸盒尺寸拨盘选在U6时,纸名称的ON/OFF\",,,,,,\"0:OFF(缺省值),液晶显示U1;1:ON时,液晶显示(CST-U6)所指定的纸张名称\"
,\"COPIER>OPTION>CST>U7-NAME\",,,,,,\"纸盒尺寸拨盘选在U7时,纸名称的ON/OFF\",,,,,,\"0:OFF(缺省值),液晶显示U1;1:ON时,液晶显示(CST-U7)所指定的纸张名称\"
,\"COPIER>OPTION>CST>U8-NAME\",,,,,,\"纸盒尺寸拨盘选在U8时,纸名称的ON/OFF\",,,,,,\"0:OFF(缺省值),液晶显示U1;1:ON时,液晶显示(CST-U8)所指定的纸张名称\"
,\"COPIER>OPTION>CST>CST-U1\",,,,,,\"纸盒尺寸拨盘选在U1时纸盒纸张名称设定\",,,,,,\"可以设定的纸盒纸名称代码:24,26,27,28,33,36,37\"
,\"COPIER>OPTION>CST>CST-U2\",,,,,,\"纸盒尺寸拨盘选在U2时纸盒纸张名称设定\",,,,,,\"可以设定的纸盒纸名称代码:35\"
,\"COPIER>OPTION>CST>CST-U3\",,,,,,\"纸盒尺寸拨盘选在U3时纸盒纸张名称设定\",,,,,,\"可以设定的纸盒纸名称代码:25\"
,\"COPIER>OPTION>CST>CST-U4\",,,,,,\"纸盒尺寸拨盘选在U4时纸盒纸张名称设定\",,,,,,\"可以设定的纸盒纸名称代码:31\"
,\"COPIER>OPTION>CST>CST-U5\",,,,,,\"纸盒尺寸拨盘选在U5时纸盒纸张名称设定\",,,,,,\"可以设定的纸盒纸名称代码:32\"
,\"COPIER>OPTION>CST>CST-U6\",,,,,,\"纸盒尺寸拨盘选在U6时纸盒纸张名称设定\",,,,,,\"可以设定的纸盒纸名称代码:34\"
,\"COPIER>OPTION>CST>CST-U7\",,,,,,\"纸盒尺寸拨盘选在U7时纸盒纸张名称设定\",,,,,,\"可以设定的纸盒纸名称代码:22,29\"
,\"COPIER>OPTION>CST>CST-U8\",,,,,,\"纸盒尺寸拨盘选在U8时纸盒纸张名称设定\",,,,,,\"可以设定的纸盒纸名称代码:23,30\"
,\"COPIER>OPTION>CST>ENV1\",,,,,,\"纸盒尺寸拨盘选在特殊时纸盒纸张名称设定\",,,,,,\"可以设定的纸盒纸代码,21:COM10;22:ISO-B5;23:Monarch;24:ISO-C5;25:DL;26:No.4\"
,\"COPIER>OPTION>CST>ENV2\",,,,,,\"纸盒尺寸拨盘选在特殊时纸盒纸张名称设定\",,,,,,\"可以设定的纸盒纸代码,21:COM10;22:ISO-B5;23:Monarch;24:ISO-C5;25:DL;26:No.4\"
,,,,,,,,\"纸盒的纸名称(略称)表\"
,,,,\"号码\",\"略称\",,\"尺寸\",,\"号码\",\"略称\",,\"尺寸\",,,\"号码\",\"略称\",,\"尺寸\"
,,,,\"01\",\"A1\",,\"A1\",,\"15\",\"B5 \",,\"B5 \",,,\"29\",\"A-LTR\",,\"阿根廷LETTER \"
,,,,\"02\",\"A2\",,\"A2\",,\"16\",\"11×17\",,\"11〃×17〃\",,,\"30\",\"A-LTTR\",,\"阿根廷LETTER-R\"
,,,,\"03\",\"A3R\",,\"A3R\",,\"17\",\"LTRR\",,\"LETTER-R\",,,\"31\",\"G-LTR\",,\"官厅LETTER \"
,,,,\"04\",\"A3\",,\"A3\",,\"18\",\"LTR \",,\"LETTER \",,,\"32\",\"G-LTRR\",,\"官厅LETTER-R\"
,,,,\"05\",\"A4R\",,\"A4R\",,\"19\",\"STMT\",,\"STATEMENT\",,,\"33\",\"A-LGL\",,\"阿根廷LEGAL\"
,,,,\"06\",\"A4\",,\"A4\",,\"20\",\"STMTR\",,\"STATEMENT-R\",,,\"34\",\"G-LGL\",,\"官厅LEGAL\"
,,,,\"07\",\"A5\",,\"A5\",,\"21\",\"LGL\",,\"LEGAL\",,,\"35\",\"FOLI\",,\"FOLIO\"
,,,,\"08\",\"A5R\",,\"A5R\",,\"22\",\"K-LGL\",,\"韩国官厅纸\",,,\"36\",\"A-OFI\",,\"阿根廷OFFICIO\"
,,,,\"09\",\"B1\",,\"B1\",,\"23\",\"K-LGLR\",,\"韩国官厅纸\",,,\"37\",\"M-OFI\",,\"墨西哥OFFICIO\"
,,,,\"10\",\"B2\",,\"B2\",,\"24\",\"FLSC\",,\"FOOLSCAP\",,,\"38\"
,,,,\"11\",\"B3\",,\"B3\",,\"25\",\"A-FLS\",,\"澳大利亚FOOLSCAP\",,,\"39\"
,,,,\"12\",\"B4R\",,\"B4R\",,\"26\",\"OFI\",,\"OFICIO\",,,\"40\",\"ALL\"
,,,,\"13\",\"B4 \",,\"B4 \",,\"27\",\"E-OFI\",,\"厄瓜多尔OFFICIO\"
,,,,\"14\",\"B5R\",,\"B5R\",,\"28\",\"B-OFI\",,\"玻利维亚OFFICIO\"
,\"与选购件有关的功能设定模式\",,,,,,,\"COPIER>OPTION>ACC>\",,,,,,\"5-94T\"
,\"COPIER>OPTION>ACC>COIN\",,,,,,,\"将控制面板控制卡设定为显示投币机(COIN)\",,,,,,\"0:OFF(缺省值)\",,,\"1:ON,显示投币机(COIN)\"
,\"COPIER>OPTION>ACC>DK-P\",,,,,,,\"选购件3500张右侧纸仓(L1)的纸尺寸设定\",,,,,,\"0:A4(缺省值);1:B5;2:LTR3;3:A-LYR 注:设定后要将电源开关OFF后再ON\"
,\"外部控制器的设定\",,,,,,,\"COPIER>OPTION>INT-FACE\"
,\"COPIER>OPTION>INT-FACE>IMG-CONT\",,,,,,,\"外部控制器的设定\",,,,,,\"0:OFF(缺省值)\"
,,,,,,,,,,,,,,\"1:ON 可以设定外部控制器的使用(连接显示,改变用户模式显示;改变网络设定)\"
,\"6.2\",\"输稿器>选项\",,,,,,\"FEEDER>OPTION>\",,,,,,,\"5-95T\"
,\"FEEDER>OPTION>SIZE-SW\",,,,,,,\"AB尺寸原稿与英制原稿混合使用的检测设定\",,,,,,\"0:混合使用不能检测(缺省值)\",,,,,\"1:混合使用可以检测\"
,\"6.3\",\"分页器>选项\",,,,,,\"SORTER>OPTION>\",,,,,,,\"5-95T\"
,\"SORTER>OPTION>BLNK-SW\",,,,,,,\"使用鞍式装订器时折叠位置的空白宽度设定\",,,,,,\"0:正常模式,空白宽度5毫米;1:加宽模式,空白宽度10毫米(缺省值)\"
,\"SORTER>OPTION>MD-PRTN\",,,,,,,\"分页器出错时托盘收回设定\",,,,,,\"0:禁止(缺省值); 1:允许托盘收回, 注:设定后要将电源开关OFF后再ON\"
,\"6.4\",\"卡>选项\",,,,,,\"BOARD>OPTION>\",,,,,,,\"5-96T\"
,\"BOARD>OPTION>MENUE-1\",,,,,,,\"显示打印设定菜单的第1级菜单\",,,,,,\"0:不显示(缺省值)\",,,\"1:显示\"
,\"BOARD>OPTION>MENUE-2\",,,,,,,\"显示打印设定菜单的第2级菜单\",,,,,,\"0:不显示(缺省值)\",,,\"1:显示\"
,\"BOARD>OPTION>MENUE-3\",,,,,,,\"显示打印设定菜单的第3级菜单\",,,,,,\"0:不显示(缺省值)\",,,\"1:显示\"
,\"BOARD>OPTION>MENUE-4\",,,,,,,\"显示打印设定菜单的第4级菜单\",,,,,,\"0:不显示(缺省值)\",,,\"1:显示\"
,\"BOARD>OPTION>PCI1-OFF\",,,,,,,\"PCI插座1中的卡发生故障时关闭该口\",,,,,,\"0:正常模式(缺省值);1:关闭该PCI口\"
,\"BOARD>OPTION>PCI2-OFF\",,,,,,,\"PCI插座2中的卡发生故障时关闭该口\",,,,,,\"0:正常模式(缺省值);1:关闭该PCI口\"
,\"BOARD>OPTION>PCI3-OFF\",,,,,,,\"PCI插座3中的卡发生故障时关闭该口\",,,,,,\"0:正常模式(缺省值);1:关闭该PCI口\"
,\"7.\",\"复印>测试打印\",,,,,,\"COPIER>TEST\",,,,,,,\"5-97T\"
,,\"Display\",,,\"I/O\",,\"Adjust\",,\"Function\",,,\"Option\",,\"Test\",,\"Counter\"
,,\"PG\",,,\"测试打印类型选择\"
,,\"NETWORK\",,,\"网络测试\"
,\"COPIER>TEST>PG>TYPE\",,,,,,,\"测试打印\",,,,,\"选择PG,输入要测试打印的种类号,显示反转后按OK键开始打印输出,\"
,,,,,,,,,,,,,\"打印结束后,必须返回到种类号为\"00\\\"的普通打印模式\\\";按复位键退出PG画面,\"
,,,\"种类号\",,,,,,,,\" \"
,,,\"00\",\"从CCD输入图像的(普通打印)模式\"
,,,\"01\",\"打印格子图案\",,,,,\"检查激光光轴错位(直线性,对角线),BD不良\"
,,,\"02\",\"打印有浓度补偿的17级灰度图案\",,,,,\"灰度不良,检查激光系统;底灰检查鼓,显影器,激光系统;带状白线,检查显影系统,转印带电辊,\"
,,,,,,,,,,,\"线状白线是标准白板脏引起的光补偿不良;左右浓度差,一次带电脏,显影系统不良\"
,,,\"03\",\"打印无浓度补偿的17级灰度图案\",,,,,\"灰度不良检查激光系统;底灰检查鼓,显影器,激光系统;带状白线,检查显影系统,转印带电辊,\"
,,,,,,,,,,,\"线状白线是标准白板脏引起的光补偿不良;左右浓度差,一次带电辊脏,显影系统不良\"
,,,\"04\",\"打印全白图案,\",,,,,\"如果有底灰检查感光鼓,显影器,激光系统\"
,,,\"05\",\"打印半色调图案,\",,,,,\"转印不良纵向白漏印检查转印带电辊,分离除电针,黑线检查鼓和一次带电辊\"
,,,\"06\",\"打印全黑图案,\",,,,,\"如果有白漏印检查一次带电辊,分离除电针;如果有白线是标准白板脏引起的光补偿不良\"
,,,\"07\",\"打印纵向直线图案; \",,,,,\"检查激光光轴直线性错位,BD不良\"
,,,\"08\",\"打印横向直线图案\",,,,,\"检查激光光轴直线性错位,BD不良\"
,\"COPIER>TEST>PG>TXPH\",,,,,,,\"测试打印时文字模式/照片模式切换\",,,,,\"0:文字模式 ;1:照片模式\",,,,\"(仅在测试打印时有效退出PG画面无效)\"
,\"COPIER>TEST>PG>PG-PICK\",,,,,,,\"测试打印时供纸纸路的选择\",,,,,\"1:前置纸盒1(缺省值);2:前置纸盒1;3:前置纸盒1;\"
,,,,,,,,,,,,,\"4:前置纸盒4;7:选购件3500张右侧纸仓(L1);8:手送纸托盘\"
,\"有关网络的测试\",,,,,,,\"COPIER>TEST>NETWORK\",,,,,,,\"5-99T\"
,,\"Display\",,,\"I/O\",,\"Adjust\",,\"Function\",,,\"Option\",,\"Test\",,\"Counter\"
,,,,,\"NETWORK\",,,\"\",,,\"\"
,,,\"PING\",,\"OK/NG\",,,,\"0.\",\"0.\",\"0.\",\"0.\"
,,,,,\"↑ 检测结果显示\",,,,\"↑ 输入IP地址\"
,,,,\"←\",,,\"→\",,,,,,\" /—\",,,\"OK\"
,\"COPIER>TEST>NETWORK>PING\"
,,\"确认复印机与网络(仅TCP/IP)的连接情况,新机安装时进行与网络连接的确认,以及网络连接出问题时执行该模式,操作方法如下:\"
,,\"1,关闭主电源; \"
,,\"2,接好网络电缆,打开电源; \"
,,\"3,进行网络设定; \"
,,\"4,进行网络的确认,输入PING确认远程主机地址(用户网络中的PC端的IP地址) ;\"
,,\"5,选择COPIER>TEST>NETWORK>PING,使用操作面板上的数字键输入第4步确认的IP地址,按OK键(网络连接正常时显示\\\"OK\\\"\"
,,\"如果显示\\\"NG\\\"时,首先确认网络电缆的连接;如网络电缆连接正确进行第6步;网络电缆有问题,重新连接后再进行第5步;\"
,,\"6,选择COPIER>TEST>NETWORK>PING,使用操作面板上的数字键输入ROOP BACK地址*注(127.0.0.1),按\\\"OK\\\"键再按复印键.\"
,,\" 如果显示\\\"NG\\\",可能本机的TCP/IP设定有问题,返回到第3步再次确认设定;如果显示\\\"OK\\\",本机的TCP/IP设定无问题,可能是网卡接口(NIC)部分有问题由第7步确认\"
,,\" *注ROOP BACK地址在网卡接口(NIC)前返回,为此可以对本机的TCP/IP设定,自身进行确认\"
,,\"7,选择COPIER>TEST>NETWORK>PING,使用操作面板上的数字键输入,当前主机的IP地址后按\\\"OK\\\"键\"
,,\" 如果显示\\\"NG\\\",可能是网卡接口(NIC)连接有问题,确认网卡接口(NIC)的连接或更换网卡接口(NIC);\"
,,\" 如果显示\\\"OK\\\",本机的网络设定和网卡接口(NIC)无问题\"
,\"8.\",\"复印>计数器模式\",,,,,,\"COPIER>COUNTER\",,,,,,,\"5-102T\"
,,,\"Display\",,\" \",\"I/O\",,\"Adjust\",,\"Function\",,\"Option\",,\"Test\",,\"Counter\"
,,,\"TOTAL\",,,,,,\"总计数器\"
\" \",,,,,,\" \"
,,,\"PICK-UP\",,,,,,\"搓纸计数器\",,,\" \",\" \"
,,,,,,,,,,,,\" \"
,,,\"FEEDER\",,,,,,\"输稿器计数器\"
,,,\"JAM\",,,\"DRBL-1\",,,\"卡纸计数器\",,,\"消耗零部件计数器-1\"
\" \",,,,,,\"DRBL-2\",,,,,,\"消耗零部件计数器-2\"
,,,,,,,,,,,,,,,,\" \"
,\"计数器清除步骤:\",,,,\"选择要清除的项目,该项目显示反转后按操作面板上的清除键,该项目的计数器被清除到\\\"00000000\\\"\"
,,,,,\"注:小尺寸(S)的纸计数1张;大尺寸(L)的纸计数2张;\"
,\"定期更换/消耗品零部件(定期更换PRDC-1/消耗品零部件DRBL-1/消耗品零部件DRBL-2)计数器的检查: \"
,,\"例:TR-ROOL / 00000201 / 00240000 / 0% !! 000082\"
,,\"TR-ROOL,零部件名称, 本例中的TR-ROOL为转印电极辊\"
,,\"00000201 为转印电极辊计数器实际已使用张数 (该零部件更换后要将该计数器清除)\"
,,\"00240000 为转印电极辊零部件寿命限定的使用张数 \"
,,,,\"(在该项目中的数据可以设定,数据设定后按\\\"OK\\\"键)\"
,,\"0% 为实际使用张数与限定使用张数的比值,\"
,,\"!! 为实际使用张数与限定使用张数的比值达到90～100%时显示1个 ! ;超过100%时显示2个 !! \"
\" \",\" \",\"000082 为预计在82天后需要更换转印电极辊零部件. \"
,,,,,,\"计数器菜单项目表\",,,,,,,,,\"5-102T\"
,\"复印>计数器>总计数器\",,,,,,,,\"COPIER>COUNTER>TOTAL>\"
,\"COPIER>COUNTER>TOTAL>SERVECE1\",,,,,,,,\"维修总计数器1\"
,\"COPIER>COUNTER>TOTAL>SERVECE2\",,,,,,,,\"维修总计数器2\"
,\"COPIER>COUNTER>TOTAL>COPY\",,,,,,,,\"复印总计数器\"
,\"COPIER>COUNTER>TOTAL>PPL\",,,,,,,,\"打印计数器\"
,\"COPIER>COUNTER>TOTAL>FAX-PRT\",,,,,,,,\"传真接收打印计数器\"
,\"COPIER>COUNTER>TOTAL>RMT-PRT\",,,,,,,,\"遥控打印总计数器\"
,\"COPIER>COUNTER>TOTAL>BOX-PRT\",,,,,,,,\"BOX打印总计数器\"
,\"COPIER>COUNTER>TOTAL>RPT-PRT\",,,,,,,,\"报告打印总计数器\"
,\"COPIER>COUNTER>TOTAL>2-SIDE\",,,,,,,,\"双面打印总计数器\"
,\"COPIER>COUNTER>TOTAL>SCAN\",,,,,,,,\"扫描器计数器\"
,\"复印>计数器>纸路搓纸计数器\",,,,,,,,\"COPIER>COUNTER>PICK-UP>\"
,\"COPIER>COUNTER>PICK-UP>C1\",,,,,,,,\"前置纸盒1搓纸总计数器\"
,\"COPIER>COUNTER>PICK-UP>C2\",,,,,,,,\"前置纸盒2搓纸总计数器\"
,\"COPIER>COUNTER>PICK-UP>C3\",,,,,,,,\"前置纸盒3搓纸总计数器\"
,\"COPIER>COUNTER>PICK-UP>C4\",,,,,,,,\"前置纸盒4搓纸总计数器\"
,\"COPIER>COUNTER>PICK-UP>MF\",,,,,,,,\"手送纸盘的搓纸总计数器\"
,\"COPIER>COUNTER>PICK-UP>DK\",,,,,,,,\"选购件3500张右侧纸仓(L1)的搓纸总计数器\"
,\"COPIER>COUNTER>PICK-UP>2-SIDE\",,,,,,,,\"双面第2面的搓纸总计数器\"
,\"复印>计数器>输稿器计数器\",,,,,,,,\"COPIER>COUNTER>FEEDER\"
,\"COPIER>COUNTER>FEEDER>FEED\",,,,,,,,\"输稿器搓纸总计数器\"
,\"复印>计数器>卡纸计数器\",,,,,,,,\"COPIER>COUNTER>JAM\"
,\"COPIER>COUNTER>JAM>TOTAL\",,,,,,,,\"主机卡纸总计数器\"
,\"COPIER>COUNTER>JAM>FEEDER\",,,,,,,,\"输稿时卡纸总计数器\"
,\"COPIER>COUNTER>JAM>SORTER\",,,,,,,,\"分页(Finishr)时卡纸总计数器\"
,\"COPIER>COUNTER>JAM>2-SIDE\",,,,,,,,\"双面卡纸总计数器\"
,\"COPIER>COUNTER>JAM>MF\",,,,,,,,\"手送纸盘的卡纸总计数器\"
,\"COPIER>COUNTER>JAM>C1\",,,,,,,,\"前置纸盒1卡纸总计数器\"
,\"COPIER>COUNTER>JAM>C2\",,,,,,\" \",,\"前置纸盒2卡纸总计数器\"
,\"COPIER>COUNTER>JAM>C3\",,,,,,,,\"前置纸盒3卡纸总计数器\"
,\"COPIER>COUNTER>JAM>C4\",,,,,,,,\"前置纸盒4卡纸总计数器\"
,\"COPIER>COUNTER>JAM>DK\",,,,,,,,\"选购件3500张右侧纸仓(L1)的卡纸总计数器\"
,\"复印>计数器>消耗零部件计数器-1\",,,,,,,,\"COPIER>COUNTER>DRBL-1>\"
,\"COPIER>COUNTER>PRDC-1>PRE-LMP\",,,,,,,,\"一次充电辊计数器\"
,\"COPIER>COUNTER>PRDC-1>TR-ROLL\",,,,,,,,\"转印辊计数器\"
,\"COPIER>COUNTER>PRDC-1>SP-SC-EL\",,,,,,,,\"纸分离放电针计数器\"
,\"COPIER>COUNTER>DRBL-1>DVG-CYL\",,,,,,,,\"显影辊计数器\"
,\"COPIER>COUNTER>DRBL-1>C1-PU-RL\",,,,,,,,\"前置纸盒1搓纸轮计数器\"
,\"COPIER>COUNTER>DRBL-1>C1-SP-RL\",,,,,,,,\"前置纸盒1分离轮计数器\"
,\"COPIER>COUNTER>DRBL-1>C1-FD-RL\",,,,,,,,\"前置纸盒1输纸辊计数器\"
,\"COPIER>COUNTER>DRBL-1>C2-PU-RL\",,,,,,,,\"前置纸盒2搓纸轮计数器\"
,\"COPIER>COUNTER>DRBL-1>C2-SP-RL\",,,,,,,,\"前置纸盒2分离轮计数器\"
,\"COPIER>COUNTER>DRBL-1>C2-FD-RL\",,,,,,,,\"前置纸盒2输纸辊计数器\"
,\"COPIER>COUNTER>DRBL-1>C3-PU-RL\",,,,,,,,\"前置纸盒3搓纸轮计数器\"
,\"COPIER>COUNTER>DRBL-1>C3-SP-RL\",,,,,,,,\"前置纸盒3分离轮计数器\"
,\"COPIER>COUNTER>DRBL-1>C3-FD-RL\",,,,,,,,\"前置纸盒3输纸辊计数器\"
,\"COPIER>COUNTER>DRBL-1>C4-PU-RL\",,,,,,,,\"前置纸盒4搓纸轮计数器\"
,\"COPIER>COUNTER>DRBL-1>C4-SP-RL\",,,,,,,,\"前置纸盒4分离轮计数器\"
,\"COPIER>COUNTER>DRBL-1>C4-FD-RL\",,,,,,,,\"前置纸盒4输纸辊计数器\"
,\"COPIER>COUNTER>DRBL-1>M-PU-RL\",,,,,,,,\"手送纸盘搓纸轮计数器\"
,\"COPIER>COUNTER>DRBL-1>M-SP-RL\",,,,,,,,\"手送纸盘分离辊计数器\"
,\"COPIER>COUNTER>DRBL-1>FX-LW-RL\",,,,,,,,\"定影下辊计数器\"
,\"COPIER>COUNTER>DRBL-1>FX-UNIT\",,,,,,,,\"定影单元计数器\"
,\"COPIER>COUNTER>DRBL-1>FX-FILM\",,,,,,,,\"定影薄膜计数器\"
,\"COPIER>COUNTER>DRBL-1>FX-CL-RL\",,,,,,,,\"定影下辊清洁辊计数器\"
,\"复印>计数器>消耗零部件计数器-2\",,,,,,,,\"COPIER>COUNTER>DRBL-2>\"
,\"COPIER>COUNTER>DRBL-1>DF-PU-RL\",,,,,,,,\"ADF的搓纸轮计数器\"
,\"COPIER>COUNTER>DRBL-1>DF-SP-RL\",,,,,,,,\"ADF的分离板计数器\"
,\"COPIER>COUNTER>DRBL-1>DF-SP-PD\",,,,,,,,\"ADF的分离垫片计数器\"
,\"COPIER>COUNTER>DRBL-1>DF-FD-RL\",,,,,,,,\"ADF的纸输送轮计数器\"
,\"COPIER>COUNTER>DRBL-1>LNT-TAPE\",,,,,,,,\"ADF的集尘带计数器\"
,\"COPIER>COUNTER>DRBL-1>PD-PU-RL\",,,,,,,,\"选购件3500张右侧纸仓(L1)的搓纸轮计数器\"
,\"COPIER>COUNTER>DRBL-1>PD-SP-RL\",,,,,,,,\"选购件3500张右侧纸仓(L1)的分离轮计数器\"
,\"COPIER>COUNTER>DRBL-1>PD-FD-RL\",,,,,,,,\"选购件3500张右侧纸仓(L1)的纸输送轮计数器\"
,\"COPIER>COUNTER>DRBL-1>FIN-STPR\",,,,,,,,\"装订器计数器\"
,\"COPIER>COUNTER>DRBL-1>SDL-STPL\",,,,,,,,\"鞍式装订计数器\"
,\"COPIER>COUNTER>DRBL-1>PUNCH\",,,,,,,,\"打孔计数器\"
\"iR2200,2800,3300 输入输出检查\"
\"制作:WGF\"
\"共页 ,第页\"
,\"3.\",\"输入/输出动作确认\",,,,,,\"I/O\",,,,,,,,\"5-20T\"
,,,\"Display\",,,\"I/O\",,\"Adjust\",,,\"Function\",,,\"Option\",,,,\"Test\",,\"Counter\"
,,,,\"DC-CON\",,,,,,\"DC驱动板的输入/输出动作确认\",,,,,,,,\"P001～P035\"
,,,,\"R-CON\",,,,,,\"读取控制板的输入/输出动作确认\",,,,,,,,\"IO-P01～IO-P13\"
,,,,\"MN-CON\",,,,,,\"主制板的输入/输出动作确认\",,,,,,,,\"P001～P010\"
,,,,\"FEEDER(DADF-H1)\",,,,,,\"输稿器的输入/输出动作确认\",,,,,,,,\"IO-P01～IO-P11;AD-P01～AD-P03\"
,,,,\"SORTER(Finisher-J1)\",,,,,,\"Finisher-J1分页器的输入/输出动作确认\",,,,,,,,\"IO-P001～IO-P011\"
,,,,\"SORTER(Saddle Finisher-G1)\",,,,,,\"鞍式分页装订器-G1的输入/输出动作确认\",,,,,,,,\"P001～P015;P023～P030\"
,,,,\"Saddle Finisher-G1,Puncher\",,,,,,\"鞍式分页装订器-G1的Puncher打孔组件\",,,,,,,,\"P016～P022;P031～P038\"
,\"3.1\",\"DC驱动板输入/输出动作确认\",,,,,,,,\"1/7\",,\"COPIER>I/O>DC-CON \",,,,,,,,\"5-21T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P001\",\"0\",\"M1\",,,,\"输出口\",,,,,\"主电机\"
,\"P001\",\"1\",\"LAMP2\",,,,\"输出口\",,,,,\"预曝光灯\"
,\"P001\",\"2\",\"M10\",,,,\"输出口\",,,,,\"驱动6个光反射面菱镜的激光扫描电机\"
,\"P001\",\"3\",\"M4\",,,,\"输出口\",,,,,\"定影电机\"
,\"P001\",\"4\",\"M4\",,,,\"输出口\",,,,,\"定影电机\"
,\"P001\",\"5\",\"CL1\",,,,\"输出口\",,,,,\"纵向输纸辊离合器\"
,\"P001\",\"6\",\"CL2\",,,,\"输出口\",,,,,\"手进纸盘搓离合器MLT-CL\"
,\"P001\",\"7\",\"CL3\",,,,\"输出口\",,,,,\"显影器离合器\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P002\",\"0\",\"SL1\",,,,\"输出口\",,,,,\"纸盘1,2搓纸轮下降电磁铁SL1(使凸轮放,搓纸轮向下降)\"
,\"P002\",\"1\",\"SL3Z\",,,,\"输出口\"
,\"P002\",\"3\",\"SL5\",,,,\"输出口\",,,,,\"手进纸盘搓纸导板放电磁铁MTL-SL\"
,\"P002\",\"4\",\"SL6\",,,,\"输出口\",,,,,\"一次充电辊清洁电磁铁\"
,\"P002\",\"5\",\"M9\",,,,\"输出口\",,,,,\"对位辊电机\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P003\",\"0\",\"M2\",,,,\"输出口\",,,,,\"搓纸电机驱动信号-1\"
,\"P003\",\"1\",\"M2\",,,,\"输出口\",,,,,\"搓纸电机驱动信号-2\"
,\"P003\",\"2\",\"M2\",,,,\"输出口\",,,,,\"搓纸电机驱动信号-3\"
,\"P003\",\"3\",\"M2\",,,,\"输出口\",,,,,\"搓纸电机驱动信号-4\"
,\"P003\",\"4\",\"M3\",,,,\"输出口\",,,,,\"横向对位传感器步进电机\",,,,,\"A相\"
,\"P003\",\"5\",\"M3\",,,,\"输出口\",,,,,\"横向对位传感器步进电机\",,,,,\"A/相\"
,\"P003\",\"6\",\"M3\",,,,\"输出口\",,,,,\"横向对位传感器步进电机\",,,,,\"B相\"
,\"P003\",\"7\",\"M3\",,,,\"输出口\",,,,,\"横向对位传感器步进电机\",,,,,\"B/相\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P004\",\"0\",\"FM1\",,,,\"输出口\",,,,,\"显影器冷却风扇\",,,\"全速信号\"
,\"P004\",\"1\",\"FM2\",,,,\"输出口\",,,,,\"定影器冷却风扇\",,,\"全速信号\"
,\"P004\",\"2\",\"FM1\",,,,\"输出口\",,,,,\"显影器冷却风扇\",,,\"半速信号\"
,\"P004\",\"3\",\"FM2\",,,,\"输出口\",,,,,\"定影器冷却风扇\",,,\"半速信号\"
,\"P004\",\"4\",\"M8B\",,,,\"输出口\",,,,,\"内置2路纸托盘-A1纸排出步进电机脉冲信号IN1\"
,,,\"M7Z\",,,,\"输出口\",,,,,\"中继排纸组件,纸排出步进电机脉冲信号IN1\"
,\"P004\",\"5\",\"M8B\",,,,\"输出口\",,,,,\"内置2路纸托盘-A1纸排出步进电机脉冲信号IN2\"
,,,\"M7Z\",,,,\"输出口\",,,,,\"中继排纸组件,纸排出步进电机脉冲信号IN2\"
,\"P004\",\"6\",\"M8B\",,,,\"输出口\",,,,,\"内置2路纸托盘-A1纸排出步进电机脉冲信号IN3\"
,,,\"M7Z\",,,,\"输出口\",,,,,\"中继排纸组件,纸排出步进电机脉冲信号IN3\"
,\"P004\",\"7\",\"M8B\",,,,\"输出口\",,,,,\"内置2路纸托盘-A1纸排出步进电机脉冲信号IN4\"
,,,\"M7Z\",,,,\"输出口\",,,,,\"中继排纸组件,纸排出步进电机脉冲信号IN4\"
,,\"DC驱动板输入/输出动作确认\",,,,,,\"2/7\",,,,\"COPIER>I/O>DC-CON \",,,,,,,,\"5-22T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P005\",\"0\",\"M6\",,,,\"输出口\",,,,,\"双面部件纸输送电机脉冲信号IN1\"
,\"P005\",\"1\",\"M6\",,,,\"输出口\",,,,,\"双面部件纸输送电机脉冲信号IN2\"
,\"P005\",\"2\",\"M6\",,,,\"输出口\",,,,,\"双面部件纸输送电机脉冲信号IN3\"
,\"P005\",\"3\",\"M6\",,,,\"输出口\",,,,,\"双面部件纸输送电机脉冲信号IN4\"
,\"P005\",\"4\",\"M6\",,,,\"输出口\",,,,,\"双面部件纸输送电机驱动信号I0\"
,\"P005\",\"5\",\"M6\",,,,\"输出口\",,,,,\"双面部件纸输送电机驱动信号I1\"
,\"P005\",\"6\",\"FM4\",,,,\"输出口\",,,,,\"卷曲减少风扇(FM4)驱动信号\"
,\"P005\",\"7\",\"FM5\",,,,\"输出口\",,,,,\"卷曲减少风扇(FM5)驱动信号\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P006\",\"0\",,,,,\"输出口\",,,,,\"一次充电辊DC高压ON信号\"
,\"P006\",\"1\",,,,,\"输出口\",,,,,\"一次充电辊高压ON信号\"
,\"P006\",\"2\",,,,,\"输出口\",,,,,\"分离放电针高压ON信号\"
,\"P006\",\"3\",,,,,\"输出口\",,,,,\"显影AC偏压ON信号\"
,\"P006\",\"4\",,,,,\"输出口\",,,,,\"显影DC偏压ON信号\"
,\"P006\",\"5\",,,,,\"输出口\",,,,,\"定影偏压ON信号\"
,\"P006\",\"6\",,,,,\"输出口\",,,,,\"定影辊加热器继电器ON信号\"
,\"P006\",\"7\",\"M8B\",,,,\"输出口\",,,,,\"内置2路纸托盘-A1,纸排出步进电机脉冲信号I0\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P007\",\"0\",,,,,\"输出口\",,,,,\"转印模式信号-0\"
,\"P007\",\"1\",,,,,\"输出口\",,,,,\"转印模式信号-1\"
,\"P007\",\"2\",,,,,\"输出口\",,,,,\"转印模式信号-2\"
,\"P007\",\"3\",,,,,\"输出口\",,,,,\"转印模式信号-3\"
,\"P007\",\"4\",,,,,\"输出口\",,,,,\"转印模式信号-4\"
,\"P007\",\"5\",,,,,\"输出口\",,,,,\"转印高压信号\"
,\"P007\",\"6\",,,,,\"输出口\",,,,,\"扫描输出信号-4\"
,\"P007\",\"7\",,,,,\"输出口\",,,,,\"扫描输出信号-5\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P008\",\"0\",\"S1\",,,,\"输入口\",,,,,\"墨粉检测信号\"
,\"P008\",\"2\",\"S2\",,,,\"输入口\",,,,,\"废粉瓶满检测信号\"
,\"P008\",\"3\",\"M1\",,,,\"输入口\",,,,,\"主电机锁住信号\"
,\"P008\",\"4\",\"M10\",,,,\"输入口\",,,,,\"激光扫描电机锁住信号\"
,\"P008\",\"5\",\"M4\",,,,\"输入口\",,,,,\"定影电机锁住信号\"
,\"P008\",\"6\",,,,,\"输入口\",,,,,\"24V检测信号\"
,\"P008\",\"7\",\"SW3\",,,,\"输入口\",,,,,\"前门打开/关闭检测信号\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P009\",\"0\",,,,,\"输入口\",,,,,\"工厂用信号-0\"
,\"P009\",\"1\",,,,,\"输入口\",,,,,\"工厂用信号-1\"
,\"P009\",\"2\",,,,,\"输入口\",,,,,\"工厂用信号-2\"
,\"P009\",\"3\",,,,,\"输入口\",,,,,\"工厂用信号-3\"
,\"P009\",\"4\",\"FM1\",,,,\"输入口\",,,,,\"显影器冷却风扇旋转检测信号\"
,\"P009\",\"5\",\"FM2\",,,,\"输入口\",,,,,\"定影器冷却风扇旋转检测信号\"
,\"P009\",\"6\",\"FM4\",,,,\"输入口\",,,,,\"卷曲减少风扇(FM4)驱动信号旋转检测信号\"
,\"P009\",\"7\",\"FM5\",,,,\"输入口\",,,,,\"卷曲减少风扇(FM5)驱动信号旋转检测信号\"
,,\"DC驱动板输入/输出动作确认\",,,,,,,,\"3/7\",,\"COPIER>I/O>DC-CON \",,,,,,,,\"5-23T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\",,,,\"输出口\"
,\"P010\",\"0\",\"M5\",,,,\"输出口\",,,,,\"定影纸垂直向上排出步进电机脉冲信号A-D0\"
,\"P010\",\"1\",\"M5\",,,,\"输出口\",,,,,\"定影纸垂直向上排出步进电机脉冲信号A-D1\"
,\"P010\",\"2\",\"M5\",,,,\"输出口\",,,,,\"定影纸垂直向上排出步进电机脉冲信号A-D2\"
,\"P010\",\"3\",\"M5\",,,,\"输出口\",,,,,\"定影纸垂直向上排出步进电机脉冲信号A-相\"
,\"P010\",\"4\",\"M5\",,,,\"输出口\",,,,,\"定影纸垂直向上排出步进电机脉冲信号B-D0\"
,\"P010\",\"5\",\"M5\",,,,\"输出口\",,,,,\"定影纸垂直向上排出步进电机脉冲信号B-D1\"
,\"P010\",\"6\",\"M5\",,,,\"输出口\",,,,,\"定影纸垂直向上排出步进电机脉冲信号B-D2\"
,\"P010\",\"7\",\"M5\",,,,\"输出口\",,,,,\"定影纸垂直向上排出步进电机脉冲信号B-相\"
,\"P010\",\"8\",\"M5\",,,,\"输出口\",,,,,\"定影纸垂直向上排出步进电机脉冲信号I0\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\",,,,\"输出口\"
,\"P011\",\"0\",\"M7B\",,,,\"输出口\",,,,,\"内置2路纸托盘-A1,向No.2盘排纸的进入轮驱动步进电机脉冲信号A-D0\"
,\"P011\",\"1\",\"M7B\",,,,\"输出口\",,,,,\"内置2路纸托盘-A1,向No.2盘排纸的进入轮驱动步进电机脉冲信号A-D1\"
,\"P011\",\"2\",\"M7B\",,,,\"输出口\",,,,,\"内置2路纸托盘-A1,向No.2盘排纸的进入轮驱动步进电机脉冲信号A-D2\"
,\"P011\",\"3\",\"M7B\",,,,\"输出口\",,,,,\"内置2路纸托盘-A1,向No.2盘排纸的进入轮驱动步进电机脉冲信号A-相\"
,\"P011\",\"4\",\"M7B\",,,,\"输出口\",,,,,\"内置2路纸托盘-A1,向No.2盘排纸的进入轮驱动步进电机脉冲信号B-D0\"
,\"P011\",\"5\",\"M7B\",,,,\"输出口\",,,,,\"内置2路纸托盘-A1,向No.2盘排纸的进入轮驱动步进电机脉冲信号B-D1\"
,\"P011\",\"6\",\"M7B\",,,,\"输出口\",,,,,\"内置2路纸托盘-A1,向No.2盘排纸的进入轮驱动步进电机脉冲信号B-D2\"
,\"P011\",\"7\",\"M7B\",,,,\"输出口\",,,,,\"内置2路纸托盘-A1,向No.2盘排纸的进入轮驱动步进电机脉冲信号B-相\"
,\"P011\",\"8\",\"M7B\",,,,\"输出口\",,,,,\"内置2路纸托盘-A1,向No.2盘排纸的进入轮驱动步进电机脉冲信号I0\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P012\",\"0\",,,,,\"输出口\",,,,,\"激光输出允许信号\"
,\"P012\",\"1\",,,,,\"输出口\",,,,,\"打印输出准备就绪信号\"
,\"P012\",\"2\",,,,,\"输出口\",,,,,\"传送准备就绪信号\"
,\"P012\",\"3\",,,,,\"输出口\",,,,,\"扫描开始信号\"
,\"P012\",\"4\",,,,,\"输出口\",,,,,\"选择输出信号-0\"
,\"P012\",\"5\",,,,,\"输出口\",,,,,\"选择输出信号-1\"
,\"P012\",\"6\",,,,,\"输出口\",,,,,\"选择输出信号-2\"
,\"P012\",\"7\",,,,,\"输出口\",,,,,\"选择输出信号-3\"
,,\"DC驱动板输入/输出动作确认\",,,,,,,,\"4/7\",,\"COPIER>I/O>DC-CON \",,,,,,,,\"5-24T\"
,\"P013\",\"0\",\"S4\",,,,\"输入口\",,,,,\"前置纸盒1,纸尺寸检测信号-0\"
,\"P013\",\"1\",\"S4\",,,,\"输入口\",,,,,\"前置纸盒1,纸尺寸检测信号-1\"
,\"P013\",\"2\",\"S4\",,,,\"输入口\",,,,,\"前置纸盒1,纸尺寸检测信号-2\"
,\"P013\",\"3\",\"S4\",,,,\"输入口\",,,,,\"前置纸盒1,纸尺寸检测信号-3\"
,\"P013\",\"4\",\"S4\",,,,\"输入口\",,,,,\"前置纸盒1,纸尺寸检测信号-4\"
,\"P013\",\"5\",\"PS1\",,,,\"输入口\",,,,,\"前置纸盒1,有纸/无纸传感器PS1\"
,\"P013\",\"6\",\"PS3\",,,,\"输入口\",,,,,\"前置纸盒1纸剩余量传感器-1\",,,,,\"25%,bit6=0;bit7=1\"
,\"P013\",\"7\",\"PS4\",,,,\"输入口\",,,,,\"前置纸盒1纸剩余量传感器-2\",,,,,\"50%,bit6=1;bit7=1\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P014\",\"0\",\"S5\",,,,\"输入口\",,,,,\"前置纸盒2,纸尺寸检测信号-0\"
,\"P014\",\"1\",\"S5\",,,,\"输入口\",,,,,\"前置纸盒2,纸尺寸检测信号-1\"
,\"P014\",\"2\",\"S5\",,,,\"输入口\",,,,,\"前置纸盒2,纸尺寸检测信号-2\"
,\"P014\",\"3\",\"S5\",,,,\"输入口\",,,,,\"前置纸盒2,纸尺寸检测信号-3\"
,\"P014\",\"4\",\"S5\",,,,\"输入口\",,,,,\"前置纸盒2,纸尺寸检测信号-4\"
,\"P014\",\"5\",\"PS2\",,,,\"输入口\",,,,,\"前置纸盒2,有纸/无纸传感器PS2\"
,\"P014\",\"6\",\"PS5\",,,,\"输入口\",,,,,\"前置纸盒2纸剩余量传感器-1\",,,,,\"25%,bit6=0;bit7=1\"
,\"P014\",\"7\",\"PS6\",,,,\"输入口\",,,,,\"前置纸盒2纸剩余量传感器-2\",,,,,\"50%,bit6=1;bit7=1\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P015\",\"0\",\"PS7\",,,,\"输入口\",,,,,\"前置纸盒1再搓纸传感器PS7\"
,\"P015\",\"1\",\"PS8\",,,,\"输入口\",,,,,\"前置纸盒2再搓纸传感器PS8\"
,\"P015\",\"2\",\"PS9\",,,,\"输入口\",,,,,\"预对位辊传感器PS9,(纵向输纸)\"
,\"P015\",\"3\",\"PS10\",,,,\"输入口\",,,,,\"对位辊传感器PS10,(水平输纸)\"
,\"P015\",\"4\",\"PS11\",,,,\"输入口\",,,,,\"双面纸横向对位传感器PS11(Y-REG-PD)开始激光图像曝光(主扫描图像对位)\"
,\"P015\",\"5\",\"PS13\",,,,\"输入口\",,,,,\"定影出口纸输送辊传感器PS13\",,,,,,,,,\"高压电源板\",,,,,,,,,,,\"\\\"E069\\\"\"
,\"P015\",\"6\",\"PS15\",,,,\"输入口\",,,,,\"No.1接纸盘(机内基本接纸盘)排纸检测传感器PS15\",,,,,,,,,\"高压电源板\"
,\"P015\",\"7\",\"PS16\",,,,\"输入口\",,,,,\"No.1接纸盘(机内基本接纸盘)排纸溢出检测传感器PS16\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P016\",\"0\",\"PS17\",,,,\"输入口\",,,,,\"纸张进入双面纸盘传感器PS17\"
,\"P016\",\"1\",\"PS18\",,,,\"输入口\",,,,,\"纸张从双面纸盘排出传感器PS18\"
,\"P016\",\"2\",\"PS19B\",,,,\"输入口\",,,,,\"No.2接纸盘(内置2路纸托盘-A1的上层)排纸检测传感器PS19B\"
,\"P016\",\"3\",\"PS20B\",,,,\"输入口\",,,,,\"No.2接纸盘(内置2路纸托盘-A1的上层)排纸溢出检测传感器PS20B\"
,\"P016\",\"4\",\"PS21B\",,,,\"输入口\",,,,,\"No.3接纸盘(外置接纸托盘)排纸检测传感器PS21B\"
,\"P016\",\"5\",\"PS22\",,,,\"输入口\",,,,,\"手进纸盘,有纸/无纸传感器PS22\"
,\"P016\",\"6\",\"PS23\",,,,\"输入口\",,,,,\"右边门打开/关闭检测传感器\"
,\"P016\",\"7\",\"PS24B\",,,,\"输入口\",,,,,\"内置2路纸托盘-A1,排纸部打开/关闭检测传感器PS24B\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P017\",\"0\",\"M5\",,,,\"输入口\",,,,,\"选择输入信号-0\"
,\"P017\",\"1\",\"M4\",,,,\"输入口\",,,,,\"选择输入信号-1\"
,\"P017\",\"2\",\"M6\",,,,\"输入口\",,,,,\"选择输入信号-2\"
,\"P017\",\"3\",\"M6\",,,,\"输入口\",,,,,\"选择输入信号-3\"
,\"P017\",\"4\",\"M7\",,,,\"输入口\",,,,,\"选择输入信号-4\"
,,\"DC驱动板输入/输出动作确认\",,,,,,,,\"5/7\",,\"COPIER>I/O>DC-CON \",,,,,,,,\"5-25T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\",,,,\"输入口\"
,\"P018\",\"0\",,,,,,,,,,\"打印开始信号\"
,\"P018\",\"1\",,,,,,,,,,\"传送请求信号\"
,\"P018\",\"2\",,,,,,,,,,\"控制器电源供给接入准备就绪信号\"
,\"P018\",\"3\",,,,,,,,,,\"打印电源供给接入信号\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\",,,,\"输入口\"
,\"P019\",\"0\",,,,,,,,,,\"BD出错信号\"
,\"P019\",\"1\",,,,,,,,,,\"hysync出错信号\"
,\"P019\",\"2\",,,,,,,,,,\"副扫描线中断信号\"
,\"P019\",\"3\",,,,,,,,,,\"图像结束信号\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P020\",\"0\",,,,,,,,,,\"零交叉信号\"
,\"P020\",\"1\",,,,,,,,,,\"定影加热器触发信号-1\"
,\"P020\",\"2\",,,,,,,,,,\"定影加热器触发信号-2\"
,\"P020\",\"3\",,,,,,,,,,\"定影加热器出错OFF信号\"
,\"P020\",\"6\",\"M9\",,,,,,,,,\"对位辊步进电机脉冲信号A\"
,\"P020\",\"7\",\"M9\",,,,,,,,,\"对位辊步进电机脉冲信号B\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P021\",\"0\",\"PS26\",,,,,,,,,\"定影热辊薄膜转动检测信号\"
,\"P021\",\"6\",\"分页器-J1(Finisher-J1)检测信号\",,,,,,,,,\"内置2路纸托盘-A1,不在bit6=1\"
,\"P021\",\"7\",\"鞍式分页装订器-G1(Saddle Finisher-G1)检测信号\",,,,,,,,,\"分页器-J1(Finisher-J1)检测信号bit6=0;bit7=1\"
,,,,,,,,,,,,\"鞍式分页装订器-G1(Saddle Finisher-G1)检测信号bit6=0;bit7=0\"
,,\"DC驱动板输入/输出动作确认\",,,,,,,\"6/7\",,,\"COPIER>I/O>DC-CON \",,,,,,,,\"5-26T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P022\",\"0\",,,,,,,,,,\"控制器通信信号\"
,\"P022\",\"1\",,,,,,,,,,\"电源供给通信信号\"
,\"P022\",\"2\",,,,,,,,,,\"控制器通信信号\"
,\"P022\",\"3\",,,,,,,,,,\"电源供给通信信号\"
,\"P022\",\"5\",,,,,,,,,,\"控制器通信信号\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P023\",\"0\",\"TH1\",,,,,,,,,\"主(中间)热敏电阻M-TH1\"
,\"P023\",\"1\",\"TH2\",,,,,,,,,\"副(边缘)热敏电阻S-TH2\"
,\"P023\",\"2\",\"VR1\",,,,,,,,,\"手进纸宽度检测信号\"
,\"P023\",\"3\",,,,,,,,,,\"鼓热敏电阻\"
,\"P023\",\"4\",\"S3\",,,,,,,,,\"显示环境传感器检测到的机温度\"
,\"P023\",\"5\",\"S3\",,,,,,,,,\"显示环境传感器检测到的机内相对湿度\"
,\"P023\",\"6\",,,,,,,,,,\"AC监控信号\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P024\",\"0\",,,,,,,,,,\"RS232C调试检测信号\"
,\"P024\",\"1\",,,,,,,,,,\"RS232C调试检测信号\"
,\"P024\",\"3\",,,,,,,,,,\"电源供给通信信号\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P025\",\"1\",,,,,,,,,,\"模/数变换器ADC接收数据信号\"
,\"P025\",\"2\",,,,,,,,,,\"模/数变换器ADC串行时钟信号\"
,\"P025\",\"3\",,,,,,,,,,\"模/数变换器ADC传送数据信号\"
,\"P025\",\"4\",,,,,,,,,,\"出错中断信号\"
,\"P025\",\"5\",,,,,,,,,,\"DDI中断信号\"
,\"P025\",\"6\",,,,,,,,,,\"电源供给通信信号\"
,\"P025\",\"7\",\"PS12\",,,,,,,,,\"转印前输纸棍前端的图像前沿传感器PS12\"
,,\"DC驱动板输入/输出动作确认\",,,,,,,,\"7/7\",,\"COPIER>I/O>DC-CON \",,,,,,,,,,\"5-27T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P027\",\"0\",\"100/200V检测信号\",,,,,,,,,\"1:100V;0:200V\"
,\"P027\",\"2\",\"模/数变换器ADC芯片选择信号\"
,\"P027\",\"7\",\"φ端\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P028\",\"0\",\"CPU检查LED ON信号\"
,\"P029\",,\"TH1\",,,,,,,,,\"主(中间)热敏电阻M-TH1\"
,\"P030\",,\"TH2\",,,,,,,,,\"副(边缘)热敏电阻S-TH2\"
,\"P031\",,\"VR1\",,,,,,,,,\"手进纸宽度检测信号\"
,\"P032\",,,,,,,,,,,\"鼓热敏电阻\"
,\"P033\",,\"S3\",,,,,,,,,\"显示环境传感器检测到的机温度\"
,\"P034\",,\"S3\",,,,,,,,,\"显示环境传感器检测到的机内相对湿度\"
,\"P035\",,,,,,,,,,,\"AC监控信号\"
,,\"读出控制板输入/输出动作确认\",,,,,,,,\"1/3\",,\"COPIER>I/O>R-CON\",,,,,,,,,,\"5-28T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P01\",\"0\",\"M400\",,,,,,,,,\"原稿扫描电机时钟信号\"
,\"IO-P01\",\"1\",\"M400\",,,,,,,,,\"原稿扫描电机旋转方向信号信号\",,,,,,,\"0:顺时针CW\"
,\"IO-P01\",\"2\",\"M400\",,,,,,,,,\"原稿扫描电机驱动允许信号\",,,,,,,\"0:驱动允许\"
,\"IO-P01\",\"4\",\"M400\",,,,,,,,,\"扫描电机返回原位/扫描电机复位信号\",,,,,,,\"1→0返回到原位\"
,\"IO-P01\",\"5\",\"M400\",,,,,,,,,\"原稿扫描电机激励模式设置信号\",,,,,,,\"缺省值\"
,\"IO-P01\",\"7\",\"M400\",,,,,,,,,\"原稿扫描电机激励模式设置信号\",,,,,,,\"缺省值\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P02\",\"0\",,,,,,,,,,\"EEPROM时钟信号\",,,,,,,\"时钟\"
,\"IO-P02\",\"1\",,,,,,,,,,\"EEPROM片选择信号\",,,,,,,\"1:输出\"
,\"IO-P02\",\"2\",,,,,,,,,,\"EEPROM串行数据读出时钟信号\",,,,,,,\"数据\"
,\"IO-P02\",\"3\",,,,,,,,,,\"EEPROM串行数据写入时钟信号\",,,,,,,\"数据\"
,\"IO-P02\",\"4\",,,,,,,,,,\"扫描器接收准备就绪信号\",,,,,,,\"0:接收准备就绪\"
,\"IO-P02\",\"5\",,,,,,,,,,\"扫描器电源供给准备就绪信号\",,,,,,,\"0:准备就绪\"
,\"IO-P02\",\"7\",,,,,,,,,,\"CCD 12V ON/OFF控制信号\",,,,,,,\"1:ON\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P3\",\"0\",,,,,,,,,,\"DDI串行数据传送信号\",,,,,,,\"数据\"
,\"IO-P3\",\"1\",,,,,,,,,,\"RS232C串行数据传送信号\",,,,,,,\"数据\"
,\"IO-P3\",\"2\",,,,,,,,,,\"DDI串行数据接收信号\",,,,,,,\"数据\"
,\"IO-P3\",\"3\",,,,,,,,,,\"RS232C串行数据接收信号\",,,,,,,\"数据\"
,\"IO-P3\",\"4\",,,,,,,,,,\"CCD驱动信号输出控制信号\",,,,,,,\"1:ON\"
,\"IO-P3\",\"5\",\"SDI\",,,,,,,,,\"原稿扫描驱动控制信号\",,,,,,,\"0:ON\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P04\",\"4\",\"SDI\",,,,,,,,,\"原稿传感器信号\"
,\"IO-P04\",\"6\",\"M400\",,,,,,,,,\"原稿扫描电机驱动电流设置信号\"
,,\"读出控制板输入/输出动作确认\",,,,,,,,\"2/3\",,\"COPIER>I/O>R-CON\",,,,,,,,,,\"5-29T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P05\",\"0\",,,,,,,,,,\"DDI打印开始信号\",,,,,,,\"0:ON\"
,\"IO-P05\",\"1\",,,,,,,,,,\"模拟处理器数据信号\",,,,,,,\"数据\"
,\"IO-P05\",\"2\",,,,,,,,,,\"模拟处理器时钟信号\",,,,,,,\"时钟\"
,\"IO-P05\",\"3\",,,,,,,,,,\"模拟处理器负载信号\",,,,,,,\"数据\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P06\",\"0\",\"M400\",,,,,,,,,\"原稿扫描电机驱动电流方式信号\",,,,,,,\"0:新电流方式\"
,\"IO-P06\",\"1\",,,,,,,,,,\"电路板PCB检查方式信号\",,,,,,,\"0:检查方式\"
,\"IO-P06\",\"2\",\"FLIN\",,,,,,,,,\"原稿曝光灯ON/OFF控制信号\",,,,,,,\"1:ON\"
,\"IO-P06\",\"3\",\"FLIN\",,,,,,,,,\"原稿曝光灯变流器出错信号\",,,,,,,\"1:出错\"
,\"IO-P06\",\"4\",\"PS400\",,,,,,,,,\"原稿曝光灯架原位传感器信号\",,,,,,,\"1:曝光灯架在原位\"
,\"IO-P06\",\"5\",\"ADF图像前沿信号\",,,,,,,,,\"ADF图像前沿信号\",,,,,,,\"1:ADF图像前沿信号中断请求\"
,\"IO-P06\",\"6\",\"PS401\",,,,,,,,,\"原稿盖板25度角度检测传感器信号\",,,,,,,\"1:原稿盖板关闭\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P07\",\"5\",,,,,,,,,,\"IR-Lifter/IR-STD ID信号\",,,,,,,\"1:IR-Lifter模式\"
,\"IO-P7\",\"6\",,,,,,,,,,\" 24V监测信号\",,,,,,,\"0: 24V正常\"
,\"IO-P7\",\"7\",,,,,,,,,,\"3.3V电压降低检测信号\",,,,,,,\"1:检测到 3.3V电压降低\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P08\",\"0\",,,,,,,,,,\"DDI普通口-0 读出器→控制器\"
,\"IO-P08\",\"1\",,,,,,,,,,\"DDI普通口-1 读出器→控制器\"
,\"IO-P08\",\"2\",,,,,,,,,,\"DDI普通口-2 读出器→控制器\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P09\",\"0\",,,,,,,,,,\"ON LED\"
,,\"读出控制板输入/输出动作确认\",,,,,,,,\"3/3\",,\"COPIER>I/O>R-CON\",,,,,,,,,,\"5-29T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P13\",\"0\",,,,,,,,,,\"DDI普通口-0 控制器→读出器\",,,,,,,\"注:\"
,\"IO-P13\",\"1\",,,,,,,,,,\"DDI普通口-1 控制器→读出器\"
,\"IO-P13\",\"2\",,,,,,,,,,\"DDI普通口-2 控制器→读出器\"
,\"IO-P13\",\"3\",,,,,,,,,,\"DDI控制器电源供给准备就绪信号\",,,,,,,\"0:准备就绪\"
,\"IO-P13\",\"4\",,,,,,,,,,\"DDI控制器接收准备就绪信号\",,,,,,,\"0:接收准备就绪\"
,,\"主控制板输入/输出动作确认\",,,,,,\"1/2\",,,,\"COPIER>I/O>MN-CON\",,,,,,,,\"5-31T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P001\",\"0\",\"PWR1\",,,,,,,,,\"1:正常工作\"
,\"P001\",\"1\",\"PWR2\",,,,,,,,,\"1:正常工作\"
,\"P001\",\"2\",\"Wtachdog timer clear\",,,,,,,,,\"看门狗计时器清除\"
,\"P001\",\"3\",\"PCI节电控制\",,,,,,,,,\"1:正常工作\"
,\"P001\",\"4\",,,,,,,,,,\"风扇ON\"
,\"P001\",\"5\",,,,,,,,,,\"LED 1008\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P002\",\"0\",\"DDI-S输入信号\",,,,,,,,,\"未用\"
,\"P003\",\"1\",\"DDI-S输入信号\",,,,,,,,,\"未用\"
,\"P004\",\"2\",\"DDI-S输入信号\",,,,,,,,,\"未用\"
,\"P005\",\"3\",\"SPI\",\"SPRTST打印器开始启动信号\",,,,,,,,\"0:读出器图像开始信号\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P003\",\"0\",\"DDI-P输入信号\",,,,,,,,,\"未用\"
,\"P003\",\"1\",\"DDI-P输入信号\",,,,,,,,,\"未用\"
,\"P003\",\"2\",\"DDI-P输入信号\",,,,,,,,,\"未用\"
,\"P003\",\"3\",\"PPI PSCNST扫描器开始启动信号\",,,,,,,,,\"0:读出器开始信号\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P004\",\"0\",\"DDI-S\",,,,,,,,,\"未用\"
,\"P004\",\"1\",\"SSI-S\",,,,,,,,,\"未用\"
,\"P004\",\"2\",\"3.3V非全夜电源OFF信号\",,,,,,,,,\"0:正常(ON);1:5W(OFF)睡眠模式\"
,\"P004\",\"3\",\"PPI PSCNST\",,,,,,,,,\"未用\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P005\",\"0\",\"DDI-P输出信号\",,,,,,,,,\"未用\"
,\"P005\",\"1\",\"DDI-P输出信号\",,,,,,,,,\"未用\"
,\"P005\",\"2\",\"DDI-P输出信号\",,,,,,,,,\"未用\"
,\"P005\",\"3\",\"PPO PPRTST打印图像开始启动信号\",,,,,,,,,\"0:打印图像开开始信号\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P006\",\"0\",\"电池坏\",,,,,,,,,\"0:正常;1:电池出错报警\"
,\"P006\",\"1\",\"parallel EEPROM R/B# 并行EEPROM忙/准备就绪\",,,,,,,,,\"工厂用\"
,\"P006\",\"2\",\"flash PROM R/B# 快闪PROM忙/准备就绪\",,,,,,,,,\"0:快闪PROM忙;1:快闪PROM准备就绪\"
,\"P006\",\"3\",\"串行ROM接入检测\",,,,,,,,,\"1:串行ROM接入\"
,\"P006\",\"4\",\"CC-IV磁卡复印控制器允许操作信号\",,,,,,,,,\"1:允许操作\"
,\"P006\",\"5\",\"硬币自动投币复印控制器允许操作信号\",,,,,,,,,\"1:允许操作\"
,\"P006\",\"6\",\"EEPROM D0串行数据\",,,,,,,,,\"EEPROM D0串行数据输入口\"
,\"P006\",\"7\",\"GPI\",\"硬盘接入检测\",,,,,,,,\"1:硬盘接入\"
,,\"主控制板输入/输出动作确认\",,,,,,,,\"2/2\",,\"COPIER>I/O>MN-CON\",,,,,,,,\"5-32T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P007\",\"0\",\"电池充电控制\",,,,,,,,,\"0:允许;1:不允许\"
,\"P007\",\"2\",\"SPO(2)\",,,,,,,,,\"DDI-S发生器输出\"
,\"P007\",\"4\",\"PCI(PDL)软件复位\",,,,,,,,,\"0:LIPS板强行复位\"
,\"P007\",\"5\",\"EEPROM CS\",,,\"EEPROM 片选\",,,,,,\"工厂用\"
,\"P007\",\"6\",\"EEPROM SCK\",,,\"EEPROM 串行数据时钟\",,,,,,\"工厂用\"
,\"P007\",\"7\",\"EEPROM DIN\",,,\"EEPROM 串行数据输入\",,,,,,\"工厂用\"
,\"P007\",\"8\",\"搓纸计数器\",,,,,,,,,\"1:计数\"
,\"P007\",\"9\",\"传真送计数器\",,,,,,,,,\"1:计数\"
,\"P007\",\"10\",\"硬币自动投币复印控制器硬币拾起计数器\",,,,,,,,,\"1:计数\"
,\"P007\",\"11\",\"硬币自动投币复印控制器硬币投入计数器\",,,,,,,,,\"1:计数\"
,\"P007\",\"12\",\"LCD背光灯控制信号\",,,,,,,,,\"1:ON\"
,\"P007\",\"14\",\"并行EEPROM写保护\",,,,,,,,,\"工厂用\"
,\"P007\",\"15\",\"GPO\",\"传真SSO强行复位\",,,,,,,,\"0:复位;1:正常\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P008\",\"0\",\"PIC-PA\",,\"FOPTI0N0\",,,,,,,\"传真SSB ID\"
,\"P008\",\"1\",,,\"FOPTI0N1\",,,,,,,\"传真SSB ID\"
,\"P008\",\"2\",,,\"FOPTI0N2\",,,,,,,\"传真SSB ID\"
,\"P008\",\"3\",,,\"color UI detect\",,,,,,,\"0:彩色UI 有\"
,\"P008\",\"4\",,,\"B/W UI detect\",,,,,,,\"0:黑/白UI 有\"
,\"P008\",\"5\",,,\"电池板检测\",,,,,,,\"0:有电池板\"
,,\"自动输稿器DADF-H1板输入/输出动作确认\",,,,,,,,,,\"COPIER>I/O>FFDER\",,,,,,\"1/2\",,,,\"5-33T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P01\",\"5\",\"LED\",,,,,\"原稿设置检测LED\",,,,,\"0:ON\",,\"J11-4\",\"LED\"
,\"IO-P01\",\"6\",\"SL1\",,,,,\"锁定电磁铁\",,,,,\"0:ON\",,\"J10-1\",\"A-SL\"
,\"IO-P01\",\"7\",\"SL2\",,,,,\"标记电磁铁\",,,,,\"0:ON\",,\"J11-2\",\"STAMP-SL\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P02\",\"0\",\"P18\",,,,,\"输纸反转传感器\",,,,,\"1:有纸\",,\"J3-12\",\"EJTS\"
,\"IO-P02\",\"1\",\"P17\",,,,,\"读出部纸检测传感器\",,,,,\"1:有纸\",,\"J3-9\",\"READS\"
,\"IO-P02\",\"2\",\"P16\",,,,,\"对位辊纸检测传感器\",,,,,\"1:有纸\",,\"J3-6\",\"REGS\"
,\"IO-P02\",\"3\",\"P11\",,,,,\"DADF打开/关闭传感器\",,,,,\"1:打开\",,\"J3-3\",\"ADFOPS\"
,\"IO-P02\",\"4\",\"M2\",\"pickup motor\",,,,\"搓纸步进电机A/相\",,,,,,,\"J8-3\"
,\"IO-P02\",\"5\",\"M2\",\"pickup motor\",,,,\"搓纸步进电机A相\",,,,,,,\"J8-4\"
,\"IO-P02\",\"6\",\"M2\",\"pickup motor\",,,,\"搓纸步进电机B/相\",,,,,,,\"J8-5\"
,\"IO-P02\",\"7\",\"M2\",\"pickup motor\",,,,\"搓纸步进电机B相\",,,,,,,\"J8-6\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P03\",\"2\",,,,,,\"图像开始信号\",,,,,,,\"J1-2\",\"EDGO\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P04\",\"0\",,,,,,\"EEPROM数据输入\"
,\"IO-P04\",\"1\",,,,,,\"EEPROM数据输出\"
,\"IO-P04\",\"2\",,,,,,\"EEPROM-CK时钟\"
,\"IO-P04\",\"3\",,,,,,\"EEPROM-CS 片选\"
,\"IO-P04\",\"4\",\"PI10\",,,,,\"原稿设置传感器\",,,,,\"1:有纸\",,\"J4-3\",\"EMPS\"
,\"IO-P04\",\"5\",\"PI9\",,,,,\"输稿器盖打开/关闭传感器\",,,,,\"1:打开\",,\"J4-6\",\"COVERS\"
,\"IO-P04\",\"6\",\"M2\",\"feed motor clock\",,,,\"进纸步进电机时种\"
,\"IO-P04\",\"7\",\"M1\",\"pickup motor clock\",,,,\"搓纸步进电机时钟\"
,,\"自动输稿器DADF-H1板输入/输出动作确认\",,,,,,,,,,\"COPIER>I/O>FFDER\",,,,,,\"2/2\",,,,\"5-34T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P05\",\"0\",\"VR1\"
,\"IO-P05\",\"1\",\"PI5\",,,,,\"原稿宽度电位器VR\",,,,,,,\"J6-4\"
,\"IO-P05\",\"2\",\"PI4\",,,,,\"原稿最沿传感器\",,,,,\"1:有纸\",,\"J6-3\",\"ENDS\"
,\"IO-P05\",\"3\",\"PI3\",,,,,\"原稿长度传感器2\",,,,,\"1:有纸\",,\"J6-2\",\"LENG-2S\"
,\"IO-P05\",\"4\",\"PI2\",,,,,\"原稿长度传感器1\",,,,,\"1:有纸\",,\"J6-1\",\"LENG-1S\"
,\"IO-P05\",\"5\",,\"push switch\",,,,\"A4/LTR 识别传感器\",,,,,\"1:A4R纸\",,\"J5-3\"
,\"IO-P05\",\"6\",\"M2\",\"feed motor\",,,,,,,,,,,,\"SKHHPK\"
,\"IO-P05\",\"7\",\"M1\",\"pickup motor\",,,,\"进纸电机 V ref\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\",,,,,\"搓纸电机 V ref\"
,\"IO-P06\",\"0\",\"M1\",\"feed motor\"
,\"IO-P06\",\"1\",\"M1\",\"feed motor\",,,,\"进纸步进电机A/相\",,,,,,,\"J7-3\"
,\"IO-P06\",\"2\",\"M1\",\"feed motor\",,,,\"进纸步进电机A相\",,,,,,,\"J7-4\"
,\"IO-P06\",\"3\",\"M1\",\"feed motor\",,,,\"进纸步进电机B/相\",,,,,,,\"J7-5\"
,\"IO-P06\",\"6\",\"PI7\",,,,,\"进纸步进电机B相\",,,,,,,\"J7-6\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\",,,,,\"读出部纸检测传感器\",,,,,\"1:有纸\",,\"J3-9\",\"READS\"
,\"IO-P09\",\"0\",\"LED4\"
,\"IO-P09\",\"1\",\"LED3\",,,,,\"维修诊断用LED4 ON信号\"
,\"IO-P09\",\"2\",\"LED2\",,,,,\"维修诊断用LED3 ON信号\"
,\"IO-P09\",\"3\",\"LED1\",,,,,\"维修诊断用LED2 ON信号\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\",,,,,\"维修诊断用LED1 ON信号\"
,\"IO-P10\",\"0\",\"DIPSW8\"
,\"IO-P10\",\"1\",\"DIPSW7\",,,,,\"维修诊断用DIP 开关8\"
,\"IO-P10\",\"2\",\"DIPSW6\",,,,,\"维修诊断用DIP 开关7\"
,\"IO-P10\",\"3\",\"DIPSW5\",,,,,\"维修诊断用DIP 开关6\"
,\"IO-P10\",\"4\",\"DIPSW4\",,,,,\"维修诊断用DIP 开关5\"
,\"IO-P10\",\"5\",\"DIPSW3\",,,,,\"维修诊断用DIP 开关4\"
,\"IO-P10\",\"6\",\"DIPSW2\",,,,,\"维修诊断用DIP 开关3\"
,\"IO-P10\",\"7\",\"DIPSW1\",,,,,\"维修诊断用DIP 开关2\"
,,,,,,,,\"维修诊断用DIP 开关1\"
,\"AD-P01\",,\"VR1\"
,\"AD-P02\",,\"M1\",\"feed motor\",,,,\"原稿宽度电位器值\",,,,\"模拟口\"
,\"AD-P03\",,\"M2\",\"pickup motor\",,,,\"纸进入(Finisher-J1)的输送电机M1电流值\"
,,,,,,,,\"搓纸电机电流值\"
,\"3.5\",\"分页器-J1板输入/输出动作确认\",,,,,,,,\"分页器-J1(Finisher-J1)\",,,,\"1/8 COPIER>I/O>SORTER\",,,,,,,,\"5-35T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"地址\",\"bit\"
,\"IO-P001\",\"2\",\"S10\",,,,,\"堆垛纸托盘纸高度传感器S10\",,,,,,,,\"1:上限\"
,\"IO-P001\",\"3\",\"S1\",,,,,\"分页器-J1(Finisher-J1)前盖打开/关闭传感器\",,,,,,,,\"0:打开;1关闭\"
,\"IO-P001\",\"4\",\"S11\",,,,,\"堆垛纸托盘纸检测传感器S11\",,,,,,,,\"1:有纸\"
,\"IO-P001\",\"5\",\"S12\",,,,,\"堆垛纸托盘下限传感器S12\",,,,,,,,\"1:下限\"
,\"IO-P001\",\"6\",\"S13\",,,,,\"堆垛纸托盘上限传感器S13\",,,,,,,,\"1:上限\"
,\"IO-P001\",\"7\",\"S3\",,,,,\"返回轮原位传感器S3\",,,,,,,,\"1:原位\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P002\",\"0\",\"S11\",,,,,\"堆垛纸托盘纸检测传感器S11\",,,,,,,,\"1:有纸\"
,\"IO-P002\",\"1\",,,,,,\"IPC chip select IPC片选信号\",,,,,,,,\"1:选中\"
,\"IO-P002\",\"2\",\"S2\",,,,,\"纸进入(Finisher-J1)检测传感器\"
,\"IO-P002\",\"3\",\"S4\",,,,,\"堆垛挡住杆原位传感器S4\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P003\",\"0\",\"S7\",,,,,\"后拍纸整理板原位传感器S7\",,,,,,,,\"1:原位\"
,\"IO-P003\",\"1\",\"S6\",,,,,\"前拍纸整理板原位传感器S6\",,,,,,,,\"1:原位\"
,\"IO-P003\",\"2\",\"S8\",,,,,\"堆垛排纸杆原位传感器S8\",,,,,,,,\"0:原位\"
,\"IO-P003\",\"3\",\"S5\",,,,,\"中间处理纸盘纸检测传感器\",,,,,,,,\"1:有纸\"
,\"IO-P003\",\"4\",\"S14\",,,,,\"装订器钉盒检测传感器(开关)S14\",,,,,,,,\"0:检测到\"
,\"IO-P003\",\"5\",\"S15\",,,,,\"装订器装订钉空传感器(开关)S15\",,,,,,,,\"0:检测到\"
,\"IO-P003\",\"6\",\"S16\",,,,,\"装订钉原位传感器S16\",,,,,,,,\"0:检测到\"
,\"IO-P003\",\"7\",\"S17\",,,,,\"装订沿传感器S17\",,,,,,,,\"0:检测到\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P004\",\"0\"
,\"IO-P004\",\"1\",\"S9\",,,,,\"分页器-J1(Finisher-J1)接纸托盘升降电机M5时钟传感器S9\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P005\",\"0\",\"M5\",,,,,\"分页器-J1(Finisher-J1)接纸托盘升降电机M5 顺时针旋转信号CW\",,,,,,,,,,,,\"1:托盘上升\"
,\"IO-P005\",\"2\",\"M5\",,,,,\"分页器-J1(Finisher-J1)接纸托盘升降电机M5 逆时针旋转信号CCW\",,,,,,,,,,,,\"1:托盘下降\"
,\"IO-P005\",\"5\",\"M1\",,,,,\"纸进入分页器-J1(Finisher-J1)的输送电机M1电流开关2,TRNSCUR2\"
,\"3.5\",\"分页器-J1板输入/输出动作确认\",,,,,,,,\"分页器-J1(Finisher-J1)\",,,,\"2/8 COPIER>I/O>SORTER\",,,,,,\"5-36T\"
,\"B\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P006\",\"0\",\"M3/M4\",,,,,\"前/后拍纸板电机M3/M4 A相信号JOGPINA\"
,\"IO-P006\",\"1\",\"M3/M4\",,,,,\"前/后拍纸板电机M3/M4 B相信号 JOGPINB\"
,\"IO-P006\",\"2\",\"M4\",,,,,\"后拍纸板电机M4允许信号BJOGPER\",,,,,,,,\"1:允许\"
,\"IO-P006\",\"3\",\"M3\",,,,,\"前拍纸板电机M3允许信号FJOGPER\",,,,,,,,\"1:允许\"
,\"IO-P006\",\"4\",\"M2\",,,,,\"纸堆垛处理电机M2 BUNDPINA\"
,\"IO-P006\",\"5\",\"M2\",,,,,\"纸堆垛处理电机M2 BUNDPINB\"
,\"IO-P006\",\"6\",\"M6\",,,,,\"装订电机M6 顺时针旋转信号STPLCW2\",,,,,,,,\"0:顺时针旋转\"
,\"IO-P006\",\"7\",\"M6\",,,,,\"装订电机M6 逆时针旋转信号STPLCCW2\",,,,,,,,\"0:逆时针旋转\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P007\",\"0\",\"M6\",,,,,\"装订电机M6 顺时针旋转信号STPLCW\",,,,,,,,,,,\"0:顺时针旋转\"
,\"IO-P007\",\"1\",\"M6\",,,,,\"装订电机M6 逆时针旋转信号STPLCCW\",,,,,,,,,,,\"0:逆时针旋转\"
,\"IO-P007\",\"2\",\"M5\",,,,,\"堆垛纸排纸托盘升降电机M5 顺时针旋转信号CW2\",,,,,,,,,,,\"1:托盘上升\"
,\"IO-P007\",\"3\",\"M5\",,,,,\"堆垛纸排纸托盘升降电机M5 逆时针旋转信号CCW2\",,,,,,,,,,,\"1:托盘下降\"
,\"IO-P007\",\"4\",\"M1\",,,,,\"纸进入分页器-J1(Finisher-J1)的输送电机M1 A相信号TRNSINA\"
,\"IO-P007\",\"5\",\"M1\",,,,,\"纸进入分页器-J1(Finisher-J1)的输送电机M1 B相信号TRNSINB\"
,\"IO-P007\",\"7\",\"M1\",,,,,\"纸进入分页器-J1(Finisher-J1)的输送电机M1 OFF信号TRNS\",,,,,,,,,,,\"1:电流ON\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P008\",\"0\",\"SW1\",,,,,\"push switch signal\",,,,\"维修诊断用按键开关SW1\",,,,,,,\"0:开关SW1 ON\"
,\"IO-P008\",\"7\"
,,,\"24VP\",,,,,\"24VP电源检测信号POWER\",,,,,,,,,,,\"0:24VP电源正常\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P010\",\"0\",\"DSW1-0\",,,,,\"维修诊断用DIP 开关0\"
,\"IO-P010\",\"1\",\"DSW1-1\",,,,,\"维修诊断用DIP 开关1\"
,\"IO-P010\",\"2\",\"DSW1-2\",,,,,\"维修诊断用DIP 开关2\"
,\"IO-P010\",\"3\",\"DSW1-3\",,,,,\"维修诊断用DIP 开关3\"
,\"IO-P010\",\"4\",\"DSW1-4\",,,,,\"维修诊断用DIP 开关4\"
,\"IO-P010\",\"5\",\"DSW1-5\",,,,,\"维修诊断用DIP 开关5\"
,\"IO-P010\",\"6\",\"DSW1-6\",,,,,\"维修诊断用DIP 开关6\"
,\"IO-P010\",\"7\",\"DSW1-7\",,,,,\"维修诊断用DIP 开关7\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"IO-P011\",\"0\",\"LED1\",,,,\"维修诊断用LED1 ON信号\"
,\"IO-P011\",\"1\",\"LED2\",,,,\"维修诊断用LED2 ON信号\"
,\"IO-P011\",\"2\",\"LED3\",,,,\"维修诊断用LED3 ON信号\"
,\"IO-P011\",\"3\",\"M1\",\"纸进入分页器-J1(Finisher-J1)的输送电机M1电流开关1,TRNSCUR\"
,\"IO-P011\",\"4\",\"M2\",,\"堆垛处理电机M2 电流开关1,BUNDSCUR1\",,,,,,,,\"0:电流高\"
,\"IO-P011\",\"5\",\"M2\",,\"堆垛处理电机M2 电流开关2,BUNDSCUR2\",,,,,,,,\"0:电流中\"
,\"IO-P011\",\"6\",\"M4\",,\"后拍纸板电机M4 电流开关,BJOGCUR\",,,,,,,,\"0:电流高\"
,\"IO-P011\",\"7\",\"M3\",,\"前拍纸板电机M3 电流开关,FJOGCUR\",,,,,,,,\"0:电流高\"
,\"3.5.2\",\"鞍式分页装订器-G1(Saddle Finisher-G1)板输入/输出动作确认\",,,,,,,,,,,,,,\"4/8 COPIER>I/O>SORTER\",,,,,,,\"5-38T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P001\",\"0\",\"M4\",,\"图8/8,前拍纸板步进电机M4 A相信号FJOGMTR-A\",,,,,,,,,,,,\"0:ON\"
,\"P001\",\"1\",\"M4\",,\"图8/8,前拍纸板步进电机M4 B相信号FJOGMTR-B\",,,,,,,,,,,,\"0:ON\"
,\"P001\",\"2\",\"M8\",,\"图7/8,装订器滑动步进电机M8 B相信号SLIDMTR-B\",,,,,,,,,,,,\"0:ON\"
,\"P001\",\"3\",\"M8\",,\"图7/8,装订器滑动步进电机M8 A相信号SLIDMTR-A\",,,,,,,,,,,,\"0:ON\"
,\"P001\",\"4\",\"M3\",,\"图7/8,纸堆垛处理盘的排纸步进电机M3 A相信号EJCTMTR-A\",,,,,,,,,,,,\"0:ON\"
,\"P001\",\"5\",\"M3\",,\"图7/8,纸堆垛处理盘的排纸步进电机M3 A/相信号EJCTMTR-A/\",,,,,,,,,,,,\"1:ON\"
,\"P001\",\"6\",\"M3\",,\"图7/8,纸堆垛处理盘的排纸步进电机M3 B相信号EJCTMTR-B\",,,,,,,,,,,,\"0:ON\"
,\"P001\",\"7\",\"M3\",,\"图7/8,纸堆垛处理盘的排纸步进电机M3 B/相信号EJCTMTR-B/\",,,,,,,,,,,,\"1:ON\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P002\",\"0\",\"M2\",,\"图8/8,蹼轮步进(将纸拉入堆垛处理盘)电机M2 A相信号PDLMTR-A\",,,,,,,,,,,,\"0:ON\"
,\"P002\",\"1\",\"M2\",,\"图8/8,蹼轮步进(将纸拉入堆垛处理盘)电机M2 A/相信号PDLMTR-A/\",,,,,,,,,,,,\"1:ON\"
,\"P002\",\"2\",\"M2\",,\"图8/8,蹼轮步进(将纸拉入堆垛处理盘)电机M2 B相信号PDLMTR-B\",,,,,,,,,,,,\"0:ON\"
,\"P002\",\"3\",\"M2\",,\"图8/8,蹼轮步进(将纸拉入堆垛处理盘)电机M2 B/相信号PDLMTR-B/\",,,,,,,,,,,,\"1:ON\"
,\"P002\",\"4\",\"M6\",,\"图7/8,接纸托盘升降(shift)电机M6,上升信号SIFTMTR-UP\"
,\"P002\",\"5\",\"M6\",,\"图7/8,接纸托盘升降(shift)电机M6,下降信号SIFTMTR-DN\"
,\"P002\",\"6\",\"M7\",,\"图8/8,鞍式装订/对折纸电机M7,脉冲宽度调制信号BINDMTR-PWM\"
,\"P002\",\"7\",\"M7\",,\"图8/8,鞍式装订/对折纸电机M7,时钟传感器信号BIND-CLK\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P003\",\"0\",,,\"图2/8,CN12-1,Puncher打孔单元数据发送信号PNCH-TXD\"
,\"P003\",\"1\",,,\"图2/8,数据发送信号-2 TXD-2(CN17-3)\"
,\"P003\",\"2\",,,\"图2/8,CN12-3,Puncher打孔单元数据接收信号PNCH-RXD\"
,\"P003\",\"3\",,,\"图2/8,数据接收信号-2 RXD-2(CN17-2)\"
,\"P003\",\"4\",\"PI24\",,\"图4/8,CN19-3接纸盘纸堆满传感器信号 PAPER-F 1:堆垛满\"
,\"P003\",\"5\",\"CL1\",,\"图7/8,SOL-CL鞍式装订输送纸堆垛轮离合器驱动命令\\\"1\\\"→Q25→CN18-2,B-CLU/\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P004\",\"1\",,,\"图2/8按钮开关PSW-1-2 ON/OFF检测\"
,\"P004\",\"2\",,,\"图1/8,DIP开关-7-8 ON/OFF检测\"
,\"P004\",\"3\",,,\"图1/8,DIP开关-5-6 ON/OFF检测\"
,\"P004\",\"4\",,,\"图1/8,DIP开关-3-4 ON/OFF检测\"
,\"P004\",\"5\",,,\"图1/8,DIP开关-1-2 ON/OFF检测\"
,\"P004\",\"6\",\"PI10\",,\"图6/8BIND-POS-DA对折纸位置传感器光发射→CN16-3 BIND-L\"
,\"P004\",\"7\",\"PI10\",,\"图6/8,BIND-POS-AD对折纸位置传感器光接收←BIND-P\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P005\",\"0\",,,\"EEPROM-CS\",,,,\"片选信号\"
,\"P005\",\"1\",,,\"EEPROM-DA-CK\",,,,\"时钟信号\"
,\"P005\",\"2\",,,\"EEPROM-DA-DO\",,,,\"数据输出信号\"
,\"P005\",\"3\",,,\"DA-LD\",,,,\"下载数据信号输出\"
,\"3.5.2\",\"鞍式分页装订器-G1(Saddle Finisher-G1)板输入/输出动作确认\",,,,,,,,,,,,,,\"5/8 COPIER>I/O>SORTER\",,,,,,,\"5-39T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P006\",\"0\",\"PI21\",,\"图4/8,CN11-6,←装订器钉位置传感器SELF-P\"
,\"P006\",\"1\",\"PI20\",,\"图4/8,CN11-5,←装订器钉空传感器HOOK-S\"
,\"P006\",\"2\",\"M5\",,\"图8/8,后拍纸板步进电机M5 A相信号RJOGMTR-A\"
,\"P006\",\"3\",\"M5\",,\"图8/8,后拍纸板步进电机M5 B相信号RJOGMTR-B\"
,\"P006\",\"4\",\"PI19\",,\"图4/8,CN11-4,←装订器原位传感器STPL-HP\"
,\"P006\",\"5\",\"PI18\",,\"图4/8,CN11-3,←装订器滑动步进电机M8原位传感器SLID-HP\"
,\"P006\",\"6\",\"PI7\",,\"图6/8,CN5-6,纸堆垛处理盘排纸皮带原位传感器EJCT-BLT-HP\"
,\"P006\",\"7\",\"REQ\",,\"请求信号\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P007\",\"5\",\"PI10\",,\"图6/8,BIND-POS-对折纸位置传感器光接收←BIND-P,CN16-2\",,,,,,,,,,\"1:有纸\"
,\"P007\",\"6\",\"PI17\",,\"接纸托盘(shift)电机M6时钟传感器PI17←图4/8,CN15-6,SIFT-CLK\"
,\"P007\",\"7\",\"PI1P\",,\"打孔原位传感器PI1P←图2/8,CN12-5,PNCH-TIM-S\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P008\",\"0\",\"M1\",,\"图7/8 CN10-3,纸输入电机M1 A相信号FEEDMTR-A\"
,\"P008\",\"1\",\"M1\",,\"图7/8 CN10-4,纸输入电机M1 A/相信号FEEDMTR-A/\"
,\"P008\",\"2\",\"M1\",,\"图7/8 CN10-5,纸输入电机M1 B相信号FEEDMTR-B\"
,\"P008\",\"3\",\"M1\",,\"图7/8 CN10-6,纸输入电机M1 B/相信号FEEDMTR-B/\"
,\"P008\",\"4\",\"M8/M4/M5\",,\"图2/8,IC15,装订器滑动步进电机M8;前/后拍纸整理板步进电机M4/M5 电流切断信号\"
,\"P008\",\"7\",\"PI8\",,\"图6/8,CN5-9,纸堆垛处理排纸盘纸空传感器←CN5-9,TRAY-EMPS\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P009\",\"0\",\"M7\",,\"图8/8,鞍式装订/对折纸电机M7顺时针旋转CW,CN6-3 STPLMTR-FWD(BINDMTR-1)\"
,\"P009\",\"1\",\"M7\",,\"图8/8,鞍式装订/对折纸电机M7逆时针旋转CCW,CN6-4 STPLMTR-REV(BINDMTR-0)\"
,\"P009\",\"2\",\"M6\",,\"图7/8,接纸托盘升降(shift)电机M6,允许信号SIFTMTR-EN\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P010\",\"0\",\"PI9\",,\"图5/8,纸表面传感器←CN5-12 LVL-S\"
,\"P010\",\"1\",\"PI4\",,\"图5/8,拍纸板传感器(前)←CN4-2 FJOG-HP\"
,\"P010\",\"2\",,,\"EEPROM数据输入\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P011\",\"0\",\"PI16\",,\"图4/8,接纸托盘下限传感器PI17,SIFT-DNLMT\"
,\"P011\",\"1\",\"PI15\",,\"图4/8,接纸托盘上限传感器PI15,SIFT-UPLMT\"
,\"P011\",\"2\",\"PWR-S\",,\"图3/8, 24VP电源监视信号 0: 24VP电源正常\"
,\"P011\",\"3\",\"PI6\",,\"图7/8,纸堆垛处理盘纸传感器信号ADJ-TRAY-S 1:有纸\"
,\"P011\",\"4\",,,\"图2/8,按钮开关SW3 ON/OFF检测 0:开关按下\"
,\"P011\",\"5\",\"MS3\",,\"图3/8,装订安全开关MS3,ON/OFF检测,←CN8-1 STPLSAFE-SW\"
,\"P011\",\"6\",\"MS1\",,\"图3/8,前门开关MS1,ON/OFF检测,←CN8-3 FDOOR-SW\"
,\"P011\",\"7\",\"MS2\",,\"图3/8,与主机连接检测开关MS2,ON/OFF检测,←CN8-5 JOINT-SW\"
,\"3.5.2\",\"鞍式分页装订器-G1(Saddle Finisher-G1)板输入/输出动作确认\",,,,,,,,,,,,,,\"6/8 COPIER>I/O>SORTER\",,,,,,,\"5-40T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P012\",\"0\",\"PI23\",,\"图6/8,鞍式分页装订器-G1的上盖ON/OFF检测传感器信号,TOPCOV-S\"
,\"P012\",\"1\",\"PI22\",,\"图6/8,鞍式分页装订器-G1的前盖ON/OFF检测传感器信号,FDOOR-S\"
,\"P012\",\"2\",\"PI5\",,\"图5/8,拍纸板传感器(后)←CN5-15 R-JOG-HP\"
,\"P012\",\"3\",\"PI3\",,\"图5/8,纸堆垛处理盘排纸轮转换导向原位传感器信号CN9-9 BDL-ROL-HP\"
,\"P012\",\"4\",\"PI2\",,\"图5/8,纸堆垛处理盘蹼轮原位传感器信号CN9-3 PDL-HP\"
,\"P012\",\"5\",\"PI1\",,\"图5/8,纸进入(鞍式分页装订器-G1)检测传感器信号ENT-S\"
,\"P012\",\"6\",\"PI11\",,\"图6/8,BIND-POS-对折纸折纸板原位传感器信号 BIND-HP\"
,\"P012\",\"7\",,,\"图4/8,装订部件接入检测信号CN11-1←STPL-CNCT/\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P013\",\"0\",\"PI12\",,\"图6/8,鞍式装订堆垛纸进纸轮(上)原位传感器信号 BIND-ROL-HP,CN16-9\"
,\"P013\",\"1\",,,\"图2/8,CN12-4,Puncher打孔单元接入检测信号PNCH-CNCT/\"
,\"P013\",\"2\",\"PI13\",,\"图4/8,鞍式装订对折纸接纸盘纸空传感器信号 CN15-3 BIND-EMPS\"
,\"P013\",\"3\",\"PWR-DN\",,\"图3/8,节电模式信号PWR-DN→图2/8,IC11-88 1:节电模式\"
,\"P013\",\"4\",\"LED1\",,\"图2/8,IC11-87,LED1 ON 信号/\"
,\"P013\",\"5\",\"LED2\",,\"图2/8,IC11-86,LED2 ON 信号/\"
,\"P013\",\"6\",\"LED3\",,\"图2/8,IC11-85,LED3 ON 信号/\"
,\"P013\",\"7\",\"ACK\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P014\",\"0\",\"图1/8,DIPSW1-1\"
,\"P014\",\"1\",,\"图1/8,DIPSW1-2\"
,\"P014\",\"2\",,\"图1/8,DIPSW1-3\"
,\"P014\",\"3\",,\"图1/8,DIPSW1-4\"
,\"P014\",\"4\",,\"图1/8,DIPSW1-5\"
,\"P014\",\"5\",,\"图1/8,DIPSW1-6\"
,\"P014\",\"6\",,\"图1/8,DIPSW1-7\"
,\"P014\",\"7\",,\"图1/8,DIPSW1-8\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P015\",\"0\",,\"图2/8,PSW1\"
,\"P015\",\"1\",,\"图2/8,PSW2\"
,\"P015\",\"2\",,\"图2/8,PSW3\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P023\",\"模拟口\",,\"图3/8,CPU IC13-112←图6/8,BIND-POS-AD对折纸位置传感器光接收←BIND-P\"
,\"P025\",\"模拟口\",,\"图2/8,PSW1,PSW2\"
,\"P026\",\"模拟口\",,\"图1/8,DIPSW1-7,8\"
,\"P027\",\"模拟口\",,\"图1/8,DIPSW1-5,6\"
,\"P028\",\"模拟口\",,\"图1/8,DIPSW1-3,4\"
,\"P029\",\"模拟口\",,\"图1/8,DIPSW1-1,2\"
,\"P030\",,,\"图3/8,CPU IC13-1121→图6/8,BIND-POS-DA对折纸位置传感器光发射→CN16-3 BIND-L\"
,\"3.5.4\",\"鞍式分页装订器-G1的Puncher打孔组件板输入/输出动作确认\",,,,,,,,,,,,,,\"7/8 COPIER>I/O>SORTER\",,,,,,,\"5-41T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P016\",\"0\",,\"阶梯电流位1\"
,\"P016\",\"1\",,\"阶梯电流位2\"
,\"P016\",\"2\",,\"阶梯电流位3\"
,\"P016\",\"3\",,\"阶梯电流位4\"
,\"P016\",\"4\",,\"阶梯电流位5\"
,\"P016\",\"5\",,\"阶梯电流位6\"
,\"P016\",\"6\",,\"阶梯电流位7\"
,\"P016\",\"7\",,\"阶梯电流位8\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P017\",\"0\",\"PI1P\",,\"图4.1,打孔器原位传感器信号PUNCH\"
,\"P017\",\"1\",\"PI2P\",,\"图4.1,水平(横向)对位原位传感器信号SLIDE\"
,\"P017\",\"4\",\"图4.1,DIPSW1001-1\",,,,\"0:开关ON\"
,\"P017\",\"5\",\"图4.1,DIPSW1001-2\",,,,\"0:开关ON\"
,\"P017\",\"6\",\"图4.1,DIPSW1001-3\",,,,\"0:开关ON\"
,\"P017\",\"7\",\"图4.1,DIPSW1001-4\",,,,\"0:开关ON\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P018\",\"0\",\"图4.1,SW1002\",,,,\"0:开关ON\"
,\"P018\",\"1\",\"图4.1,SW1003\",,,,\"0:开关ON\"
,\"P018\",\"4\",\"图4.1, 24V电源供电监测\"
,\"P018\",\"5\",\"图4.1,LED1\"
,\"P018\",\"6\",\"图4.1,LED2\"
,\"P018\",\"7\",\"图4.1,LED3\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P019\",\"0\",\"图4.1,水平(横向)对位原位传感器光强度调整\"
,\"P019\",\"1\",\"图4.1,水平(横向)对位原位传感器光强度调整\"
,\"P019\",\"4\",\"图4.1,IC1002 EEPROM-DO\"
,\"P019\",\"5\",\"图4.1,IC1002 EEPROM-DI\"
,\"P019\",\"6\",\"图4.1,IC1002 EEPROM-CLK\"
,\"P019\",\"7\",\"图4.1,IC1002 EEPROM-CS\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P020\",\"2\",\"图4.1,水平(横向)对位原位传感器中断信号\"
,\"P020\",\"3\",\"REQ\"
,\"P020\",\"4\",\"HFS RXD\"
,\"P020\",\"5\",\"HFS TXD\"
,\"P020\",\"7\",\"ACK\"
,\"3.5.3\",\"鞍式分页装订器-G1Puncher打孔组件板输入/输出动作确认\",,,,,,,,,,,,,,\"8/8 COPIER>I/O>SORTER\",,,,,,,\"5-42T\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P021\",\"0\",\"图4.1,水平(横向)对位电机M2P电流设定信号\"
,\"P021\",\"1\",\"图4.1,水平(横向)对位电机M2P电流设定信号\"
,\"P021\",\"2\",\"图4.1,水平(横向)对位电机M2P B相信号\",,,,,,,,\"J1001-2\"
,\"P021\",\"3\",\"图4.1,水平(横向)对位电机M2P A相信号\",,,,,,,,\"J1001-1\"
,\"P021\",\"4\",\"图4.1,打孔电机M1P 反转信号REV\"
,\"P021\",\"5\",\"图4.1,打孔电机M1P 正转信号FWD\"
,\"P021\",\"6\",\"图4.1,打孔电机M1P 脉冲宽度调制信号PWM\"
,\"P021\",\"7\",\"图4.1,打孔电机M1P 编码时钟信号CLOCK\"
,\"地址\",\"bit\",\"注:未使用的bit位删除\"
,\"P022\",\"2\",\"图4.1,PI3P打孔器废孔纸满传感器信号←J1005-3 DUSTPTR \"
,\"P022\",\"3\",\"图4.3,CN2011-7打孔对位传感器-5\",,,,,,\"Y REG 水平(横向)对位\"
,\"P022\",\"4\",\"图4.3,CN2011-6打孔对位传感器-4\",,,,,,\"B5R\"
,\"P022\",\"5\",\"图4.3,CN2011-5打孔对位传感器-3\",,,,,,\"A4R\"
,\"P022\",\"6\",\"图4.3,CN2011-4打孔对位传感器-2\",,,,,,\"B4\"
,\"P022\",\"7\",\"图4.3,CN2011-3打孔对位传感器-1\",,,,,,\"A4\"
,\"P031\",\"模拟口\",,\"图4.1,PI3P打孔器废孔纸满传感器信号←J1005-3 DUSTPTR \"
,\"P032\",\"模拟口\",,\"图4.3,CN2011-7打孔对位传感器-5\",,,,,,\"Y REG 水平(横向)对位\"
,\"P033\",\"模拟口\",,\"图4.3,CN2011-6打孔对位传感器-4\",,,,,,\"B5R\"
,\"P034\",\"模拟口\",,\"图4.3,CN2011-5打孔对位传感器-3\",,,,,,\"A4R\"
,\"P035\",\"模拟口\",,\"图4.3,CN2011-4打孔对位传感器-2\",,,,,,\"B4\"
,\"P036\",\"模拟口\",,\"图4.3,CN2011-3打孔对位传感器-1\",,,,,,\"A4\"
,\"P037\",\"模拟口\",,\"图4.1,水平(横向)对位原位传感器光强度调整\"
,\"P038\",\"模拟口\",,\"图4.1,对位原位传感器光强度调整\"
\"iR5000;iR6000电路接插件\"
\"制作: WGF\"
\"共页 ,第页\"
,,\"CANON 佳能 iR5000/iR6000 数码复印机电路接插件(点到点接线图)\"
,,,,,,,,,,,\"继电器RL1触点\"
,\"DC电源板(PCB2)\",,,,,,,,,,,,,,,,,,,,,,,\"漏电保护继电器开关\"
,\"J4001\",,\"主电源开关SW1\",,,,,,,,,,,,\"→\",\"接AC驱动板和定影灯\",,,,,,\"泸波器\",,,\"BLCB\"
,\"1\",,,,,,,,,,,,,,,,,,,,,,,,,,\"←\"
,\"2\",,,,,,,,,,,,,,,,,,,,,,,,,,\"←\",\"AC电源输入\"
,\"J4002\",,,,,\"DC控制板(PCB1)\"
,\"1\",\"GND\",,,\"←\",\"J102-3\",,\"DC电源板冷却风扇GND\"
,\"2\",\"FM6CLK\",,,\"→\",\"J102-2\",,\"DC电源板冷却风扇FM6CLK同步信号\"
,\"3\",\"FM6ON\",,,\"←\",\"J102-1\",,\"DC电源板冷却风扇驱动信号FM6ON\",,,,,,,,\"全速24V,半速12V\"
,\"J4003\",,,,,\"DC控制板(PCB1)\"
,\"1\",\"DCOM-24VU3\",,,\"→\",\"J101-1\"
,\"2\",\"DCOM-0V\",,,\"→\",\"J101-2\"
,\"3\",\"DCOM-12V\",,,\"→\",\"J101-3\"
,\"4\",\"DCOM-GND\",,,\"→\",\"J101-4\"
,\"5\",\"DCOM-5V\",,,\"→\",\"J101-5\",,\"5V:5.1V±3%/4.5A,过电流保护动作值1.0～5.0A\"
,\"6\",\"DCOM-0V\",,,\"→\",\"J101-6\"
,\"7\",\"DCOM-3.3VA3\",,,\"→\",\"J101-7\",,\"3.3VA1,2,3 :3.4V±3%/9.0A,过电流保护动作值5.5～8.0A\"
,\"8\",\"DCOM-0VU2\",,,\"→\",\"J101-8\",,\"24VU1,2,3,4:24.0V±5%/15.0A,过电流保护动作值2.5～5.0A\"
,,\" \",,,\" \",\" \",,\"12VU:12.0V±5%/1.0A,过电流保护动作值2.5～5.0A\"
,\"J4004\",,,,\"5V:5.1V±3%/4.5A,过电流保护动作值1.0～5.0A\"
,\"1\",\"TRAY-5V\",,,\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"J322-M1\",,\"J322-F1\",,\"J222FC-1\",,\"J222MC-1\",,\"→\",\"J2301-1\",,\"5V\"
,\"2\",\"TRAY-0V\",,,\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"J322-M2\",,\"J322-F2\",,\"J222FC-2\",,\"J222MC-2\",,\"→\",\"J2301-2\",,\"0V\"
,,,,,,,,,,,,,,,,,,,,,,,,,,,,\"双面驱动板\"
,,,,,,,,,,,\"突入电流防止电路板\"
,,,,,,,,,,,,,,\"J903-2\",,\"→\",\"→\",\"→\",\"J322-M3\",,\"J322-F3\",,\"J222FC-3\",,\"J222MC-3\",,\"→\",\"J2301-3\",,\"24V\"
,,,,,,,,,,,,,,\"J903-1\",,\"→\",\"→\",\"→\",\"J322-M4\",,\"J322-F4\",,\"J222FC-4\",,\"J222MC-4\",,\"→\",\"J2301-4\",,\" 0V\"
,\"3\",\"TRAY-24VU2\",,,\"→\",\"J1414-F3\",,\"J1414-M3\",,\"→\",\"J903-3\",,,,,,,,\"24VU1,2,3,4:24.0V±5%/15.0A,过电流保护动作值2.5～5.0A\"
,\"4\",\"TRAY-0V\",,,\"→\",\"J1414-F4\",,\"J1414-M4\",,\"→\",\"J903-4\"
,,,,,,,,\" \",,,,,,,,,,,,,,,,\"突入电流防止电路板\"
,,,\"手送纸盘关闭开关MSW2\",,,,,\"←\",\"J323M-2\",,\"J323F-1\",,\"J1404F-4\",,\"J1404M-4\",,\"←\",\"J1415-F9\",,\"J1415-M9\",,\"←\",\"J902-4\",,\" 24V\"
,,,\"手送纸盘关闭开关MSW2\",,,,,\"→\",\"J323M-1\",,\"J323F-2\",,\"J1404F-3\",,\"J1404M-3\",,\"→\",\"J1415-F8\",,\"J1415-M8\",,\"→\",\"J902-3\",,\"MULTI-24V\"
,,,,\"前门关闭开关SW2\",,,,\"←\",\"J1405M-1\",,\"J1405F-1\",,\"J1404F-2\",,\"J1404M-2\",,\"←\",\"J1415-F7\",,\"J1415-M7\",,\"←\",\"J902-2\",,\"24V\"
,,,,\"前门关闭开关SW2\",,,,\"→\",\"J1405M-2\",,\"J1405F-2\",,\"J1404F-1\",,\"J1404M-1\",,\"→\",\"J1415-F6\",,\"J1415-M6\",,\"→\",\"J902-1\",,\"门开关连锁24V\"
,\"J4005\",,\"24VU1,2,3,4:24.0V±5%/15.0A,过电流保护动作值2.5～5.0A\"
,\"1\",\"24VU1\",,,\"→\",\"J321-F1\",,\"J321-M1\",,\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"J1415-F5\",,\"J1415-M5\",,\"→\",\"J903-9\",,\"24VU1\"
,\"2\",\"GND\",,,\"→\",\"J321-F2\",,\"J321-M2\",,\"→\",\"M19;M1;M2;HVT,GND\"
,,,,,,\"M2电机板24V\",,,,,,\"J631-1\",,\"J6310M-1\",,,\"←\",\"J1415-F2\",,\"J1415-M1\",,\"←\",\"J903-5\",,\"M2-24V\"
,,,,,,\"M2电机板GND\",,,,,,\"J631-2\"
,,,,,,\"M1电机板24V\",,,,,,\"J601-1\",,,,,\"←\",\"J1415-F1\",,\"J1415-M2\",,\"←\",\"J903-6\",,\"M1-24V\"
,,,,,,\"M1电机板GND\",,,,,,\"J601-2\"
,,\"M19电机板24V\",,,,\"J289-2\",,\"←\",\"J288-1\",,\"←\",\"J251CM-1\",,\"J251CF-4\",,,\"←\",\"J1415-F3\",,\"J1415-M3\",,\"←\",\"J903-7\",,\"M19-24V\"
,,\"M19电机板GND\",,,,\"J289-1\",,\"←\",\"J288-2\",,\"←\",\"J251CM-2\",,\"J251CF-3\"
,,\"高压(HVT)电路板24V\",,,,,,\"←\",,,\"←\",\"J321-F4\",,\"J321-M4\",,,\"←\",\"J1415-F4\",,\"J1415-M4\",,\"←\",\"J903-8\",,\"HVT, 24V\"
,,\"高压(HVT)电路板GND\",,,,,,\"←\",,,\"←\",\"J321-F3\",,\"J321-M3\"
,\"J4008\",,,,,,,,,,,,,,,,\"硬盘直流供电\"
,\"1\",\"HDD, 5V\",,,\"→\",\"J321-F5\",,\"J321-M5\",,\"→\",\"J1402-F1\",,\"J1402-M1\",,,\"→\",\"J1552-1\",,\"HDD, 5V\",,,\"5V:5.1V±3%/4.5A,过电流保护动作值1.0～5.0A\"
,\"2\",\"HDD,GND\",,,\"→\",\"J321-F6\",,\"J321-M6\",,\"→\",\"J1402-F2\",,\"J1402-M2\",,,\"→\",\"J1552-2\",,\"HDD,GND\"
,\"3\",\"HDD,GND\",,,\"→\",\"J321-F7\",,\"J321-M7\",,\"→\",\"J1402-F3\",,\"J1402-M3\",,,\"→\",\"J1552-3\",,\"HDD,GND\"
,\"4\",\"HDD, 12\",,,\"→\",\"J321-F8\",,\"J321-M8\",,\"→\",\"J1402-F4\",,\"J1402-M4\",,,\"→\",\"J1552-4\",,\"HDD, 12\"
,,,,,,,,,,,,,,,,,,,\" \"
,\"J4007\",,,,\"24VU1,2,3,4:24.0V±5%/15.0A,过电流保护动作值2.5～5.0A\",,,,,,,,,,,,,,,,,\"J5105-4\",,\"ADF插座\"
,\"1\",\"24VU4\",,,\"→\",\"J8500F-1\",,\"J8500M-1\",,\"→\",\"J9009F-1\",,\"J9009M-1\",,\"→\",\"→\",\"→\",\"→\",\"24VU4\",,\"→\",\"J5105-3\",,\"ADF插座\"
,\"2\",\"GND\",,,\"→\",\"J8500F-2\",,\"J8500M-2\",,\"→\",\"J9009F-2\",,\"J9009M-2\",,\"→\",\"→\",\"→\",\"→\",\"GND\",,\"→\",\"J5105-2\",,\"ADF插座\"
,\"3\",\"24VU4\",,,\"→\",\"J8500F-3\",,\"J8500M-3\",,\"→\",\"J505-1 \",,\"→\",\"读取(扫描)控制板(PCB12)\",,,,,\"24VU4\",,,\"J5105-1\",,\"ADF插座\"
,\"4\",\"GND\",,,\"→\",\"J8500F-4\",,\"J8500M-4\",,\"→\",\"J505-2\",,\"→\",\"读取(扫描)控制板(PCB12)\",,,,,\"GND\"
,\"5\",,,,,,,,\" \"
,,,,,,,,,,,,,,\" \",,,,,,,,,\" \"
,\"J4006\",,,,,,,,,,,,,,,,,,\"J702C-4\"
,\"1\",\"0V\",,,\"→\",\"J1401F-5\",,\"J1401M-5\",,,,,\"→\",\"J235M-1\",,\"J235F-2\",,\"→\",\"J702C-3\",,,\" \"
,\"2\",\"24VU3\",,,\"→\",\"J1401F-6\",,\"J1401M-6\",,,,,\"→\",\"J235M-2\",,\"J235F-1\",,\"→\",\"J702C-2\"
,\"3\",,,,\"→\",,,,,,,,,,,,,\"接地\",\"J702C-1\"
,,,,,\"24VU1,2,3,4:24.0V±5%/15.0A,过电流保护动作值2.5～5.0A\"
,\"J4009\",,,,\"5V:5.1V±3%/4.5A,过电流保护动作值1.0～5.0A\"
,\"1\",\"5V\",,,\"→\",\"J1401F-1\",,\"J1401M-1\",,,,,\"→\",\" J2109-1\",,\"电机驱动板PCB4\"
,\"2\",\"0V\",,,\"→\",\"J1401F-2\",,\"J1401M-2\",,,,,\"→\",\" J2109-2\",,\"电机驱动板PCB4\"
,\"3\",\"24VU2\",,,\"→\",\"J1401F-3\",,\"J1401M-3\",,,,,\"→\",\" J2109-3\",,\"电机驱动板PCB4\"
,\"4\",\"0V\",,,\"→\",\"J1401F-4\",,\"J1401M-4\",,,,,\"→\",\" J2109-4\",,\"电机驱动板PCB4\"
,\"J4010 \",,,,\"24VU1,2,3,4:24.0V±5%/15.0A,过电流保护动作值2.5～5.0A\",,,,,,,,,\" \"
,\"1\",\"GND\",,,\"→\",\"J8503F-1\",,\"J8503M-1\",,,,,\"→\",\"J9012M-1\",,\"J9012F-1\",,\"→\",\"J1530-1\",,\"接NE复印数据处理控制卡板(选购件)\"
,\"2\",\"24VU4\",,,\"→\",\"J8503F-2\",,\"J8503M-2\",,,,,\"→\",\"J9012M-2\",,\"J9012F-2\",,\"→\",\"J1530-2\",,\"接NE复印数据处理控制卡板(选购件)\"
,,,,,\" \"
,\"J4011 \",,,,\"24VU1,2,3,4:24.0V±5%/15.0A,过电流保护动作值2.5～5.0A\",,,,,,,,,,\" \"
,\"1\",\"24VU4\",,,\"→\",\"J8502F-1\",,\"J8502M-1\",,,,,\"→\",\"J1534M-1\",,\"J1534F-1\",,\"→\",\"投币机(选购件)\"
,\"2\",\"GND\",,,\"→\",\"J8502F-2\",,\"J8502M-2\",,,,,\"→\",\"J1534M-2\",,\"J1534F-2\",,\"→\",\"投币机(选购件)\"
,\"J4013\",,,,\"24VA:24.0V±5%/4.0A,过电流保护动作值5.0～8.0A\"
,\"1\",\"GND\",,,\"→\",\"J9013F-1\",,\"J9013M-1\",,,,,\"→\",\"J3502-1\",,\"电源板PCB8(选购件)\"
,\"2\",\"24VA\",,,\"→\",\"J9013F-2\",,\"J9013M-2\",,,,,\"→\",\"J3502-2\",,\"电源板PCB8(选购件)\"
,\"3\",\"GND\",,,\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"J1021-3\",,\"主控制板PCG24\"
,\"4\",\"RMT-2\",,,,,,,,,,,,\"J1021-2\",,\"主控制板PCG24\"
,\"5\",\"RMT-1\",,,,,,,,,,,,\"J1021-1\",,\"主控制板PCG24\"
,,,,,\"3.3VA1,2,3 :3.4V±3%/9.0A,过电流保护动作值5.5～8.0A\"
,\"J4014\",,,,,,,,,,,,,\"主控制板(PCB24) J1020\"
,\"1\",\"3.3VA1\",,,\"→\",,\" \",,,,,,,\"J1020-1\",,,\"3.3VA1\"
,\"2\",\"3.3VA1\",,,\"→\",,,,,,,,,\"J1020-2\",,,\"3.3VA1\"
,\"3\",\"3.3VA1\",,,\"→\",,,,,,,,,\"J1020-3\",,,\"3.3VA1\"
,\"4\",\"3.3VA1\",,,\"→\",,,,,,,,,\"J1020-4\",,,\"3.3VA1\"
,\"5\",\"3.3VA1\",,,\"→\",,,,,,,,,\"J1020-5\",,,\"3.3VA1\"
,\"6\",\"GND\",,,\"→\",,,,,,,,,\"J1020-6\",,,\"GND\"
,\"7\",\"GND\",,,\"→\",,,,,,,,,\"J1020-7\",,,\"GND\"
,\"8\",\"GND\",,,\"→\",,,,,,,,,\"J1020-8\",,,\"GND\"
,\"9\",\"GND\",,,\"→\",,,,,,,,,\"J1020-9\",,,\"GND\"
,\"10\",\"GND\",,,\"→\",,,,,,,,,\"J1020-10\",,,\"GND\"
,\"11\",,,,,\" \"
,\"J4015\",,,,,,,,,,,,,\" \"
,\"1\",\"3.3VA\",,,\"→\",,,,,,,,,\"J1020-11\",,,\"3.3VA1\"
,\"2\",\"3.3VA1\",,,\"→\",,,,,,,,,\"J1020-12\",,,\"3.3VA1\"
,\"3\",\"3.3VA1\",,,\"→\",,,,,,,,,\"J1020-13\",,,\"3.3VA1\"
,\"4\",\"GND\",,,\"→\",,,,,,,,,\"J1020-14\",,,\"GND\"
,\"5\",\"GND\",,,\"→\",,,,,,,,,\"J1020-15\",,,\"GND\"
,,,,,\"5V:5.1V±3%/4.5A,过电流保护动作值1.0～5.0A\"
,\"J4016\",,,,,,,,,,,,,\"主控制板(PCB24) J1026 \"
,\"1\",\"5V\",,,\"→\",,,,,,,,,\"J1026-1\",,,\"5V\",,,\" \"
,\"2\",\"5V\",,,\"→\",,,,,,,,,\"J1026-2\",,,\"5V\",,,,,,\" \"
,\"3\",\"GND\",,,\"→\",,,,,,,,,\"J1026-3\",,,\"GND\"
,\"4\",\"GND\",,,\"→\",,,,,,,,,\"J1026-4\",,,\"GND\"
,,,\"3.3VA1,2,3 :3.4V±3%/9.0A,过电流保护动作值5.5～8.0A\"
,\"J4017\",,,,,,,,,,,,,\"中继板 J9005 \"
,\"1\",\"3.3VA2\",,,\"→\",,,,,,,,,\"J9005-1 \",,,\"3.3VA2\"
,\"2\",\"3.3VA2\",,,\"→\",,,,,,,,,\"J9005-2\",,,\"3.3VA2\"
,\"3\",\"3.3VA2\",,,\"→\",,,,,,,,,\"J9005-3\",,,\"3.3VA2\",,,,,\" \"
,\"4\",\"3.3VA2\",,,\"→\",,,,,,,,,\"J9005-4\",,,\"3.3VA2\"
,\"5\",\"3.3VA2\",,,\"→\",,,,,,,,,\"J9005-5\",,,\"3.3VA2\"
,\"6\",\"GND\",,,\"→\",,,,,,,,,\"J9005-6\",,,\"GND\"
,\"7\",\"GND\",,,\"→\",,,,,,,,,\"J9005-7\",,,\"GND\"
,\"8\",\"GND\",,,\"→\",,,,,,,,,\"J9005-8\",,,\"GND\"
,\"9\",\"GND\",,,\"→\",,,,,,,,,\"J9005-9\",,,\"GND\"
,\"10\",\"GND\",,,\"→\",,,,,,,,,\"J9005-10\",,,\"GND\"
,,,,,,,,,,,,,,,,,,\" \"
,,,,,,,,,,\" \",,,,\" \"
,\"读取(扫描)控制板(PCB12)\",,,,,,,,,\" \",,\" \"
,\"J5001\",,,,\"接保险丝板,J5601\",,,,,\"(仅100V机型)\"
,\"1\",\"加热器\",,,\"→\",,,,\"J5601-1\",,\"反光镜/镜头加热器\",,,,\"24V,读取控制板ON时_24V ON→加热器OFF;读取控制板OFF时_24V OFF→加热器ON\"
,\"3\",\"GND\",,,\"→\",,,,\"J5601-2\"
,\"J5002\",,,,,,,,,,\"CCD/AP电路板(PCB13)\"
,\"1\",\"24V\",,,\"→\",,,,\"J5112-1\",,,\"CCD/AP电路板, 24V\"
,\"2\",\"GND\",,,\"→\",,,,\"J5112-2\",,,\"GND\"
,\"3\",\"GND\",,,\"→\",,,,\"J5112-3\",,,\"GND\"
,\"4\",\"A5V\",,,\"→\",,,,\"J5112-4\",,,\"5V\"
,\"J5003\",,,,\"接CCD/AP电路板(PCB13),J5113\",,,,,,,,,,,,,\"J5003\"
,\"1\",\"GND\",,\"→\",\"J5113-40\",,\"GND\",,,,,,,,,,,\"21\",\"GND\",,,,\"J5113-20\"
,\"2\",\"EVEN7\",,\"←\",\"J5113-39\",,\"CCD的偶数图像数据A/D变换后的7位\",,,,,,,,,,,\"22\",\"GND\",,,,\"J5113-19\"
,\"3\",\"EVEN6\",,\"←\",\"J5113-38\",,\"CCD的偶数图像数据A/D变换后的6位\",,,,,,,,,,,\"23\",\"GND\",,,,\"J5113-18\"
,\"4\",\"EVEN5\",,\"←\",\"J5113-37\",,\"CCD的偶数图像数据A/D变换后的5位\",,,,,,,,,,,\"24\",\"VCLK\",,,,\"J5113-17\"
,\"5\",\"EVEN4\",,\"←\",\"J5113-36\",,\"CCD的偶数图像数据A/D变换后的4位\",,,,,,,,,,,\"25\",\"GND\",,,,\"J5113-16\"
,\"6\",\"GND\",,\"→\",\"J5113-35\",,\"GND\",,,,,,,,,,,\"26\",\"GND\",,,,\"J5113-15\"
,\"7\",\"EVEN3\",,\"←\",\"J5113-34\",,\"CCD的偶数图像数据A/D变换后的3位\",,,,,,,,,,,\"27\",\"GND\",,,,\"J5113-14\"
,\"8\",\"EVEN2\",,\"←\",\"J5113-33\",,\"CCD的偶数图像数据A/D变换后的2位\",,,,,,,,,,,\"28\",\"NC\",,,,\"J5113-13\"
,\"9\",\"EVEN1\",,\"←\",\"J5113-32\",,\"CCD的偶数图像数据A/D变换后的1位\",,,,,,,,,,,\"29\",\"AP-LD\",,,,\"J5113-12\"
,\"10\",\"EVEN0\",,\"←\",\"J5113-31\",,\"CCD的偶数图像数据A/D变换后的0位\",,,,,,,,,,,\"30\",\"NC\",,,,\"J5113-11\"
,\"11\",\"GND\",,\"→\",\"J5113-30\",,\"GND\",,,,,,,,,,,\"31\",\"RING-LD\",,,,\"J5113-10\"
,\"12\",\"ODD7\",,\"←\",\"J5113-29\",,\"CCD的奇数图像数据A/D变换后的7位\",,,,,,,,,,,\"32\",\"RING-SIN\",,,,\"J5113-9\"
,\"13\",\"ODD6\",,\"←\",\"J5113-28\",,\"CCD的奇数图像数据A/D变换后的6位\",,,,,,,,,,,\"33\",\"RING-CLK\",,,,\"J5113-8\"
,\"14\",\"ODD5\",,\"←\",\"J5113-27\",,\"CCD的奇数图像数据A/D变换后的5位\",,,,,,,,,,,\"34\",\"GND\",,,,\"J5113-7\"
,\"15\",\"ODD4\",,\"←\",\"J5113-26\",,\"CCD的奇数图像数据A/D变换后的4位\",,,,,,,,,,,\"35\",\"NC\",,,,\"J5113-6\"
,\"16\",\"GND\",,\"→\",\"J5113-25\",,\"GND\",,,,,,,,,,,\"36\",\"GND\",,,,\"J5113-5\"
,\"17\",\"ODD3\",,\"←\",\"J5113-24\",,\"CCD的奇数图像数据A/D变换后的3位\",,,,,,,,,,,\"37\",\"RSYNC\",,,,\"J5113-4\"
,\"18\",\"ODD2\",,\"←\",\"J5113-23\",,\"CCD的奇数图像数据A/D变换后的2位\",,,,,,,,,,,\"38\",\"5V\",,,,\"J5113-3\"
,\"19\",\"ODD1\",,\"←\",\"J5113-22\",,\"CCD的奇数图像数据A/D变换后的1位\",,,,,,,,,,,\"39\",\"NC\",,,,\"J5113-2\"
,\"20\",\"ODD0\",,\"←\",\"J5113-21\",,\"CCD的奇数图像数据A/D变换后的0位\",,,,,,,,,,,\"40\",\"GND\",,,,\"J5113-1\"
,\"J5004-A\",,,,,\"接主控制板(PCB24),J1014A\"
,\"1\",\"GND\",,,\"J1014-A40\",,,,,,,,,,\"21\",\"GND\",,,,\"J1014-A20\"
,\"2\",\"SPRTST\",,,\"J1014-A39\",,,,,,,,,,\"22\",\"SPOWER\",,,,\"J1014-A19\"
,\"3\",\"GND\",,,\"J1014-A38\",,,,,,,,,,\"23\",\"GND\",,,,\"J1014-A18\"
,\"4\",\"SSCNST\",,,\"J1014-A37\",,,,,,,,,,\"24\",\"GND\",,,,\"J1014-A17\"
,\"5\",\"GND\",,,\"J1014-A36\",,,,,,,,,,\"25\",\"GND\",,,,\"J1014-A16\"
,\"6\",\"SVD15\",,,\"J1014-A35\",,,,,,,,,,\"26\",\"SVCLK\",,,,\"J1014-A15\"
,\"7\",\"GND\",,,\"J1014-A34\",,,,,,,,,,\"27\",\"GND\",,,,\"J1014-A14\"
,\"8\",\"SVD13\",,,\"J1014-A33\",,,,,,,,,,\"28\",\"GND\",,,,\"J1014-A13\"
,\"9\",\"GND\",,,\"J1014-A32\",,,,,,,,,,\"29\",\"GND\",,,,\"J1014-A12\"
,\"10\",\"SVD11\",,,\"J1014-A31\",,,,,,,,,,\"30\",\"SPI 1\",,,,\"J1014-A11\"
,\"11\",\"GND\",,,\"J1014-A30\",,,,,,,,,,\"31\",\"GND\",,,,\"J1014-A10\"
,\"12\",\"SVD9\",,,\"J1014-A29\",,,,,,,,,,\"32\",\"SPO 2\",,,,\"J1014-A9\"
,\"13\",\"GND\",,,\"J1014-A28\",,,,,,,,,,\"33\",\"GND\",,,,\"J1014-A8\"
,\"14\",\"SVD7\",,,\"J1014-A27\",,,,,,,,,,\"34\",\"SPO 0\",,,,\"J1014-A7\"
,\"15\",\"GND\",,,\"J1014-A26\",,,,,,,,,,\"35\",\"GND\",,,,\"J1014-A6\"
,\"16\",\"SVD5\",,,\"J1014-A25\",,,,,,,,,,\"36\",\"SHSYNC\",,,,\"J1014-A5\"
,\"17\",\"GND\",,,\"J1014-A24\",,,,,,,,,,\"37\",\"GND\",,,,\"J1014-A4\"
,\"18\",\"SVD3\",,,\"J1014-A23\",,,,,,,,,,\"38\",\"NC\",,,,\"J1014-A3\"
,\"19\",\"GND\",,,\"J1014-A22\",,,,,,,,,,\"39\",\"GND\",,,,\"J1014-A2\"
,\"20\",\"SVD1\",,,\"J1014-A21\",,,,,,,,,,\"40\",\"NC\",,,,\"J1014-A1\"
,\"J5004-B\",,,,,\"接主控制板(PCB24),J1014B\"
,\"1\",\"GND\",,,\"J1014-B40\",,,,,,,,,,\"21\",\"SVD0\",,,,\"J1014-B20\"
,\"2\",\"SRTS\",,,\"J1014-B39\",,,,,,,,,,\"22\",\"GND\",,,,\"J1014-B19\"
,\"3\",\"GND\",,,\"J1014-B38\",,,,,,,,,,\"23\",\"SVD2\",,,,\"J1014-B18\"
,\"4\",\"GND\",,,\"J1014-B37\",,,,,,,,,,\"24\",\"GND\",,,,\"J1014-B17\"
,\"5\",\"SCTS\",,,\"J1014-B36\",,,,,,,,,,\"25\",\"SVD4\",,,,\"J1014-B16\"
,\"6\",\"GND\",,,\"J1014-B35\",,,,,,,,,,\"26\",\"GND\",,,,\"J1014-B15\"
,\"7\",\"SVSYNC\",,,\"J1014-B34\",,,,,,,,,,\"27\",\"SVD6\",,,,\"J1014-B14\"
,\"8\",\"GND\",,,\"J1014-B33\",,,,,,,,,,\"28\",\"GND\",,,,\"J1014-B13\"
,\"9\",\"SPO 1\",,,\"J1014-B32\",,,,,,,,,,\"29\",\"SVD8\",,,,\"J1014-B12\"
,\"10\",\"GND\",,,\"J1014-B31\",,,,,,,,,,\"30\",\"GND\",,,,\"J1014-B11\"
,\"11\",\"SOI 1\",,,\"J1014-B30\",,,,,,,,,,\"31\",\"SVD10\",,,,\"J1014-B10\"
,\"12\",\"GND\",,,\"J1014-B29\",,,,,,,,,,\"32\",\"GND\",,,,\"J1014-B9\"
,\"13\",\"SPI 2\",,,\"J1014-B28\",,,,,,,,,,\"33\",\"SVD12\",,,,\"J1014-B8\"
,\"14\",\"GND\",,,\"J1014-B27\",,,,,,,,,,\"34\",\"GND\",,,,\"J1014-B7\"
,\"15\",\"GND\",,,\"J1014-B26\",,,,,,,,,,\"35\",\"SVD14\",,,,\"J1014-B6\"
,\"16\",\"GND\",,,\"J1014-B25\",,,,,,,,,,\"36\",\"GND\",,,,\"J1014-B5\"
,\"17\",\"SCPRDY\",,,\"J1014-B24\",,,,,,,,,,\"37\",\"SCMD\",,,,\"J1014-B4\"
,\"18\",\"GND\",,,\"J1014-B23\",,,,,,,,,,\"38\",\"GND\",,,,\"J1014-B3\"
,\"19\",\"SPRDY\",,,\"J1014-B22\",,,,,,,,,,\"39\",\"SSTS\",,,,\"J1014-B2\"
,\"20\",\"GND\",,,\"J1014-B21\",,,,,,,,,,\"40\",\"GND\",,,,\"J1014-B1\"
,\"J5010\",,,,\"ADF插座J5105-A,J5105\"
,\"1\",\"GND\",,\"→\",\"J5105A-7\"
,\"2\",\" 24V\",,\"→\",\"J5105A-6\"
,\"3\",\"GND\",,\"→\",\"J5105A-5\",,,,\"J5105-4\"
,\"4\",\"RX\",,\"←\",\"J5105A-4\",,,,\"J5105-3\",,\"J9009-M1\",,\"J9009-F1\",,\"←\",\"J8500-M1\",,\"J8500-F1\",,\"←\",\" 24V\",,\"←\",\"J40071,DC电源板\"
,\"5\",\"TX\",,\"→\",\"J5105A-3\",,,,\"J5105-2\",,\"J9009-M2\",,\"J9009-F2\",,\"←\",\"J8500-M2\",,\"J8500-F2\",,\"←\",\"GND\",,\"←\",\"J40072,DC电源板\"
,\"6\",\"ITOP/\",,\"←\",\"J5105A-2\",,,,\"J5105-1\"
,\"7\",\"GND\",,\"→\",\"J5105A-1\"
,\"J5005\"
,\"1\",\" 24V\",,\"←\",\"←\",\"←\",\"←\",\"←\",\"←\",\"←\",\"←\",\"←\",\"←\",\"←\",\"←\",\"J8500-M3\",,\"J8500-F3\",,\"←\",\" 24V\",,\"←\",\"J40073,DC电源板\"
,\"2\",\"GND\",,\"←\",\"←\",\"←\",\"←\",\"←\",\"←\",\"←\",\"←\",\"←\",\"←\",\"←\",\"←\",\"J8500-M4\",,\"J8500-F4\",,\"←\",\"GND\",,\"←\",\"J40074,DC电源板\"
,\"J5006\",,,,,,,,,,,,\"原稿尺寸(长度)传感器PS43\"
,\"1\",\" 5V\",,,\"→\",\"J5053-M3\",,\"J5053-F1\",,,,,\"原稿尺寸(长度)传感器PS43(D-SENS3)\",,,,,,,,\" 5V\"
,\"2\",\"D-SENS3\",,,\"←\",\"J5053-M2\",,\"J5053-F2\",,,,,\"原稿尺寸(长度)传感器PS43(D-SENS3)\",,,,,,,,\"传感信号\"
,\"3\",\"GND\",,,\"→\",\"J5053-M1\",,\"J5053-F3\",,,,,\"原稿尺寸(长度)传感器PS43(D-SENS3)\",,,,,,,,\"GND\"
,\"J5007\",,,,,,,,,,,,\"原稿扫描灯LA2的变流器电路PCB18,J5101\"
,\"1\",,,,,\"J5062-M5\",,\"J5062-F1\",,,\"J5101-5\"
,\"2\",\"INV-ERR\",,,\"←\",\"J5062-M4\",,\"J5062-F2\",,\"←\",\"J5101-4\",,\"变流器电路输出开路,短路,放电等异常时\",,,,,,,,,,\"J5102-1\",,\"→\",\"曝光(氙)灯LA2\"
,\"3\",\"LAMP-ON\",,,\"→\",\"J5062-M3\",,\"J5062-F3\",,\"→\",\"J5101-3\",,\"灯ON控制信号\",,,,,,,,,,\"J5102-2\"
,\"4\",\"GND\",,,\"→\",\"J5062-M2\",,\"J5062-F4\",,\"→\",\"J5101-2\",,\"变流器电路,GND\",,,,,,,,,,\"J5102-3\"
,\"5\",\" 24V\",,,\"→\",\"J5062-M1\",,\"J5062-F5\",,\"→\",\"J5101-1\",,\"变流器电路, 24V\",,,,,,,,,,\"J5102-4\",,\"→\",\"曝光(氙)灯LA2\"
,\"J5008\",,\"未用\"
,\" J5009\"
,\"1\",\"GND\",\"未用\",,\"→\",,\" \"
,\"2\",\"RX\",\"未用\",,\"←\",,,,,,,,,,,,,,,,\" \"
,\"3\",\"TX\",\"未用\",,\"→\",,\" \"
,\"4\",\" 5V\",\"未用\",,\"→\"
,\"J5011\",,,,,\"光学扫描电机M3\",,,,,,,,,,,\" \",,\" \"
,\"1\",\"M3,A相\",,,\"→\",,\"A相\"
,\"2\",\"M3,A/相\",,,\"→\",,\"A/相\",,,,,,,,,,,\" \"
,\"3\",\"M3,B相\",,,\"→\",,\"B相\"
,\"4\",\"M3,B/相\",,,\"→\",,\"B/相\"
,\"5\",\"M3, 24V\",,,\"→\",,\" 24V\"
,\"6\",\"M3, 24V\",,,\"→\",,\" 24V\"
,,,,,,,,,,,,,,,,,,,\" \"
,\"J5012\"
,\"1\",\"GND\",,,\"→\",\"J5052-M3\",,\"J5052-F1\",,\"→\",\"J5057-3\",,\"光学扫描原位传感器PS39(HPSENS)\",,,,,,,,\"GND\"
,\"2\",\"传感信号\",,,\"←\",\"J5052-M2\",,\"J5052-F2\",,\"←\",\"J5057-2\",,\"光学扫描原位传感器PS39(HPSENS)\",,,,,,,,\"传感信号\"
,\"3\",\" 5V\",,,\"→\",\"J5052-M1\",,\"J5052-F3\",,\"→\",\"J5057-1\",,\"光学扫描原位传感器PS39(HPSENS)\",,,,,,,,\" 5V\"
,\"4\",\"GND\",,,\"→\",\"J5051-M3\",,\"J5051-F1\",,\"→\",\"J5056-3\",,\"稿台盖板位置传感器PS40(ADF-OPN\\EN)\",,,,,,,,\"GND\"
,\"5\",\"传感信号\",,,\"←\",\"J5051-M2\",,\"J5051-F2\",,\"←\",\"J5056-2\",,\"稿台盖板位置传感器PS40(ADF-OPN\\EN)\",,,,,,,,\"传感信号\",,,\"注:稿台盖板25度以下关闭\"
,\"6\",\" 5V\",,,\"→\",\"J5051-M1\",,\"J5051-F3\",,\"→\",\"J5056-1\",,\"稿台盖板位置传感器PS40(ADF-OPN\\EN)\",,,,,,,,\" 5V\"
,\"主控制板(PCB24)\"
,\"J1012-A\",,,,,,,\"接操作面板(PCB10)的J6505-A\",,,,,,,,,,\"J1012-B\",,,,,,,\"接操作面板(PCB10)的J6505-B \"
,\"1\",\"5V\",,,,,,\"15\",,,,,,,,,,\"1\",\"GND\",,,,,,\"15\"
,\"2\",\"CONT-RESET\",,,,,,\"14\",,,,,,,,,,\"2\",\"TXDM\",,,,,,\"14\"
,\"3\",\"5V\",,,,,,\"13\",,,,,,,,,,\"3\",\"GND\",,,,,,\"13\"
,\"4\",\"USOFTSW\",,,,,,\"12\",,,,,,,,,,\"4\",\"RXDM\",,,,,,\"12\"
,\"5\",\"NC\",,,,,,\"11\",,,,,,,,,,\"5\",\"GND\",,,,,,\"11\"
,\"6\",\"ONDCLK\",,,,,,\"10\",,,,,,,,,,\"6\",\"IOLCDEN\",,,,,,\"10\"
,\"7\",\"GND\",,,,,,\"9\",,,,,,,,,,\"7\",\"GND\",,,,,,\"9\"
,\"8\",\"IUOD0\",,,,,,\"8\",,,,,,,,,,\"8\",\"IOLCDF\",,,,,,\"8\"
,\"9\",\"GND\",,,,,,\"7\",,,,,,,,,,\"9\",\"GND\",,,,,,\"7\"
,\"10\",\"IUOD1\",,,,,,\"6\",,,,,,,,,,\"10\",\"IOSP\",,,,,,\"6\"
,\"11\",\"GND\",,,,,,\"5\",,,,,,,,,,\"11\",\"GND\",,,,,,\"5\"
,\"12\",\"IUOD2\",,,,,,\"4\",,,,,,,,,,\"12\",\"IOLP\",,,,,,\"4\"
,\"13\",\"GND\",,,,,,\"3\",,,,,,,,,,\"13\",\"LCDO\",,,,,,\"3\"
,\"14\",\"IUOD3\",,,,,,\"2\",,,,,,,,,,\"14\",\"5V\",,,,,,\"2\"
,\"15\",\"GND\",,,,,,\"1\",,,,,,,,,,\"15\",\"3.3V\",,,,,,\"1\"
,\"J1018-A\",,,,,,,\"接操作面板(PCB10)的J6801-A\",,,,,,,,,,\"J1018-B\",,,,,,,,\"接操作面板(PCB10)的J6801-B\"
,\"1\",\"3.3VA1\",,,,,,\"18\",,,,,,,,,,\"1\",\"5V\",,,,,,,\"18\"
,\"2\",\"GND\",,,,,,\"17\",,,,,,,,,,\"2\",\"TXCD\",,,,,,,\"17\"
,\"3\",\"FPDAT-7\",,,,,,\"16\",,,,,,,,,,\"3\",\"5V\",,,,,,,\"16\"
,\"4\",\"GND\",,,,,,\"15\",,,,,,,,,,\"4\",\"CONT-RESET\",,,,,,,\"15\"
,\"5\",\"FPDAT-5\",,,,,,\"14\",,,,,,,,,,\"5\",\"GND\",,,,,,,\"14\"
,\"6\",\"GND\",,,,,,\"13\",,,,,,,,,,\"6\",\"FPFRAME\",,,,,,,\"13\"
,\"7\",\"FPDAT-3\",,,,,,\"12\",,,,,,,,,,\"7\",\"GND\",,,,,,,\"12\"
,\"8\",\"GND\",,,,,,\"11\",,,,,,,,,,\"8\",\"LCDPWR\",,,,,,,\"11\"
,\"9\",\"FPDAT-1\",,,,,,\"10\",,,,,,,,,,\"9\",\"GND\",,,,,,,\"10\"
,\"10\",\"GND\",,,,,,\"9\",,,,,,,,,,\"10\",\"FPDAT-0\",,,,,,,\"9\"
,\"11\",\"FPHIFT\",,,,,,\"8\",,,,,,,,,,\"11\",\"GND\",,,,,,,\"8\"
,\"12\",\"GND\",,,,,,\"7\",,,,,,,,,,\"12\",\"FPDAT-2\",,,,,,,\"7\"
,\"13\",\"FPLINE\",,,,,,\"6\",,,,,,,,,,\"13\",\"GND\",,,,,,,\"6\"
,\"14\",\"GND\",,,,,,\"5\",,,,,,,,,,\"14\",\"FPDAT-4\",,,,,,,\"5\"
,\"15\",\"LCDON\",,,,,,\"4\",,,,,,,,,,\"15\",\"GND\",,,,,,,\"4\"
,\"16\",\"GND\",,,,,,\"3\",,,,,,,,,,\"16\",\"FPDAT-6\",,,,,,,\"3\"
,\"17\",\"RXDC\",,,,,,\"2\",,,,,,,,,,\"17\",\"GND\",,,,,,,\"2\"
,\"18\",\"GND\",,,,,,\"1\",,,,,,,,,,\"18\",\"SOFTSWC\",,,,,,,\"1\"
,\"J1014A\",,,,,\"接读出控制(PCB12),J5004A\",,,,,,,,\"见读出控制(PCB12),J5004A\"
,\"J1014B\",,,,,\"接读出控制(PCB12),J5004B\",,,,,,,,\"见读出控制(PCB12),J5004B\"
,\"J1015-A\",,,,,,,\"打印部分的DC控制板(PCB1)的J122-A\",,,,,,,,,,,,,,,,\"打印部分的DC控制板(PCB1)的J122-A\"
,\"1\",\"GND\",,,,,,\"40\",,,,,,,,\"21\",\"GBD\",,,,,,,\"20\"
,\"2\",\"PPI-0\",,,,,,\"39\",,,,,,,,\"22\",\"PVCKL\",,,,,,,\"19\"
,\"3\",\"GND\",,,,,,\"38\",,,,,,,,\"23\",\"GND\",,,,,,,\"18\"
,\"4\",\"PPI-1\",,,,,,\"37\",,,,,,,,\"24\",\"PHSYNC\",,\"←\",,,,,\"17\"
,\"5\",\"GND\",,,,,,\"36\",,,,,,,,\"25\",\"GND\",,,,,,,\"16\"
,\"6\",\"PPI-2\",,,,,,\"35\",,,,,,,,\"26\",\"PVD-0\",,,,,,,\"15\"
,\"7\",\"GND\",,,,,,\"34\",,,,,,,,\"27\",\"GND\",,,,,,,\"14\"
,\"8\",\"PCPRDY\",,,,,,\"33\",,,,,,,,\"28\",\"PVD-2\",,,,,,,\"13\"
,\"9\",\"GND\",,,,,,\"32\",,,,,,,,\"29\",\"GND\",,,,,,,\"12\"
,\"10\",\"PCTS\",,,,,,\"31\",,,,,,,,\"30\",\"PVD-4\",,,,,,,\"11\"
,\"11\",\"GND\",,,,,,\"30\",,,,,,,,\"31\",\"GND\",,,,,,,\"10\"
,\"12\",\"PSTS\",,,,,,\"29\",,,,,,,,\"32\",\"PVD-6\",,,,,,,\"9\"
,\"13\",\"GND\",,,,,,\"28\",,,,,,,,\"33\",\"GND\",,,,,,,\"8\"
,\"14\",\"PPRTST\",,,,,,\"27\",,,,,,,,\"34\",\"PVD-8\",,,,,,,\"7\"
,\"15\",\"GND\",,,,,,\"26\",,,,,,,,\"35\",\"GND\",,,,,,,\"6\"
,\"16\",\"PPI-3\",,,,,,\"25\",,,,,,,,\"36\",\"PVD-10\",,,,,,,\"5\"
,\"17\",\"GND\",,,,,,\"24\",,,,,,,,\"37\",\"GND\",,,,,,,\"4\"
,\"18\",\"PPI-4\",,,,,,\"23\",,,,,,,,\"38\",\"PVD-12\",,,,,,,\"3\"
,\"19\",\"GND\",,,,,,\"22\",,,,,,,,\"39\",\"GND\",,,,,,,\"2\"
,\"20\",\"PPI-5\",,,,,,\"21\",,,,,,,,\"40\",\"PVD-14\",,,,,,,\"1\"
,\"J1015-B\",,,,,,,\"打印部分的DC控制板(PCB1)的J122-B\",,,,,,,,,,,,,,,,\"打印部分的DC控制板(PCB1)的J122-B\"
,\"1\",\"GND\",,,,,,\"40\",,,,,,,,\"21\",\"GND\",,,,,,,\"20\"
,\"2\",\"PPO-0\",,,,,,\"39\",,,,,,,,\"22\",\"PPO-5\",,,,,,,\"19\"
,\"3\",\"GND\",,,,,,\"38\",,,,,,,,\"23\",\"GND\",,,,,,,\"18\"
,\"4\",\"PPO-1\",,,,,,\"37\",,,,,,,,\"24\",\"PRD\",,,,,,,\"17\"
,\"5\",\"GND\",,,,,,\"36\",,,,,,,,\"25\",\"GND\",,,,,,,\"16\"
,\"6\",\"PPO-2\",,,,,,\"35\",,,,,,,,\"26\",\"PVD-1\",,,,,,,\"15\"
,\"7\",\"GND\",,,,,,\"34\",,,,,,,,\"27\",\"GND\",,,,,,,\"14\"
,\"8\",\"PROWOR\",,,,,,\"33\",,,,,,,,\"28\",\"PVD-3\",,,,,,,\"13\"
,\"9\",\"GND\",,,,,,\"32\",,,,,,,,\"29\",\"GND\",,,,,,,\"12\"
,\"10\",\"PPRDY\",,,,,,\"31\",,,,,,,,\"30\",\"PVD-5\",,,,,,,\"11\"
,\"11\",\"GND\",,,,,,\"30\",,,,,,,,\"31\",\"GND\",,,,,,,\"10\"
,\"12\",\"PRTS\",,,,,,\"29\",,,,,,,,\"32\",\"PVD-7\",,,,,,,\"9\"
,\"13\",\"GND\",,,,,,\"28\",,,,,,,,\"33\",\"GND\",,,,,,,\"8\"
,\"14\",\"PCMD\",,,,,,\"27\",,,,,,,,\"34\",\"PVD-9\",,,,,,,\"7\"
,\"15\",\"GND\",,,,,,\"26\",,,,,,,,\"35\",\"GND\",,,,,,,\"6\"
,\"16\",\"PSCNST\",,,,,,\"25\",,,,,,,,\"36\",\"PVD-11\",,,,,,,\"5\"
,\"17\",\"GND\",,,,,,\"24\",,,,,,,,\"37\",\"GND\",,,,,,,\"4\"
,\"18\",\"PPO-3\",,,,,,\"23\",,,,,,,,\"38\",\"PVD-13\",,,,,,,\"3\"
,\"19\",\"GND\",,,,,,\"22\",,,,,,,,\"39\",\"GND\",,,,,,,\"2\"
,\"20\",\"PPO-4\",,,,,,\"21\",,,,,,,,\"40\",\"PVD-15\",,,,,,,\"1\"
,\"J1017\",,,,,,\"硬盘驱动器\",,,,,,,,\"硬盘驱动器\"
,\"1\",\"CONT-RESET\",,,,,\"J1551-1\",,,\"21\",\"IDEDMERQ\",,,,\"J1551-21\"
,\"2\",\"GND\",,,,,\"J1551-2\",,,\"22\",\"GND\",,,,\"J1551-22\"
,\"3\",\"IDED-7\",,,,,\"J1551-3\",,,\"23\",\"IDEIOW\",,,,\"J1551-23\"
,\"4\",\"IDED-8\",,,,,\"J1551-4\",,,\"24\",\"GND\",,,,\"J1551-24\"
,\"5\",\"IDED-6\",,,,,\"J1551-5\",,,\"25\",\"IDEIOR\",,,,\"J1551-25\"
,\"6\",\"IDED-9\",,,,,\"J1551-6\",,,\"26\",\"GND\",,,,\"J1551-26\"
,\"7\",\"IDED-5\",,,,,\"J1551-7\",,,\"27\",\"IDERDY\",,,,\"J1551-27\"
,\"8\",\"IDED-10\",,,,,\"J1551-8\",,,\"28\",\"GND\",,,,\"J1551-28\"
,\"9\",\"IDED-4\",,,,,\"J1551-9\",,,\"29\",\"IDEDMACK\",,,,\"J1551-29\"
,\"10\",\"IDED-11\",,,,,\"J1551-10\",,,\"30\",\"GND\",,,,\"J1551-30\"
,\"11\",\"IDED-3\",,,,,\"J1551-11\",,,\"31\",\"IDEINT\",,,,\"J1551-31\"
,\"12\",\"IDED-12\",,,,,\"J1551-12\",,,\"32\",\"NC\",,,,\"J1551-32\"
,\"13\",\"IDED-2\",,,,,\"J1551-13\",,,\"33\",\"IDEA1\",,,,\"J1551-33\"
,\"14\",\"IDED-13\",,,,,\"J1551-14\",,,\"34\",\"NC\",,,,\"J1551-34\"
,\"15\",\"IDED-1\",,,,,\"J1551-15\",,,\"35\",\"IDEA0\",,,,\"J1551-35\"
,\"16\",\"IDED-14\",,,,,\"J1551-16\",,,\"36\",\"IDEA2\",,,,\"J1551-36\"
,\"17\",\"IDED-0\",,,,,\"J1551-17\",,,\"37\",\"CS1\",,,,\"J1551-37\"
,\"18\",\"IDED-15\",,,,,\"J1551-18\",,,\"38\",\"CS3\",,,,\"J1551-38\"
,\"19\",\"GND\",,,,,\"J1551-19\",,,\"39\",\"NC\",,,,\"J1551-39\"
,\"20\",\"NC\",,,,,\"J1551-20\",,,\"40\",\"GND\",,,,\"J1551-40\"
,,,,,,,\"硬盘驱动器\"
,,,,,,,\"J1552-1\",,\"←\",\"J1402M-1\",,\"J1402F-1\",,\"←\",\"←\",\"J321M-8\",,\"J321F-8\",,\"←\",\"J4008-4\",,\"HDD-12V\",,,\"DC电源板\"
,,,,,,,\"J1552-2\",,\"←\",\"J1402M-2\",,\"J1402F-2\",,\"←\",\"←\",\"J321M-7\",,\"J321F-7\",,\"←\",\"J4008-3\",,\"HDD-GND\",,,\"DC电源板\"
,,,,,,,\"J1552-3\",,\"←\",\"J1402M-3\",,\"J1402F-3\",,\"←\",\"←\",\"J321M-6\",,\"J321F-6\",,\"←\",\"J4008-2\",,\"HDD-GND\",,,\"DC电源板\"
,,,,,,,\"J1552-4\",,\"←\",\"J1402M-4\",,\"J1402F-4\",,\"←\",\"←\",\"J321M-5\",,\"J321F-5\",,\"←\",\"J4008-1\",,\"HDD-5V\",,,\"DC电源板\"
,,,,,,,,,,,,,,,,\"J321M-4\",,\"J321F-4\"
,,,,,,,,,,,,,,,,\"J321M-3\",,\"J321F-3\"
,,,,,,,,,,,,,,,,\"J321M-2\",,\"J321F-2\"
,,,,,,,,,,,,,,,,\"J321M-1\",,\"J321F-1\"
,\"J1020\",,,,,,\"接DC电源板的J4014\"
,\"1\",\"3.3VA1\",,,\"←\",,\"J4014-1\",,\"3.3VA1\"
,\"2\",\"3.3VA1\",,,\"←\",,\"J4014-2\",,\"3.3VA1\"
,\"3\",\"3.3VA1\",,,\"←\",,\"J4014-3\",,\"3.3VA1\"
,\"4\",\"3.3VA1\",,,\"←\",,\"J4014-4\",,\"3.3VA1\"
,\"5\",\"3.3VA1\",,,\"←\",,\"J4014-5\",,\"3.3VA1\"
,\"6\",\"GND\",,,\"←\",,\"J4014-6\",,\"GND\"
,\"7\",\"GND\",,,\"←\",,\"J4014-7\",,\"GND\"
,\"8\",\"GND\",,,\"←\",,\"J4014-8\",,\"GND\"
,\"9\",\"GND\",,,\"←\",,\"J4014-9\",,\"GND\"
,\"10\",\"GND\",,,\"←\",,\"J4014-10\",,\"GND\"
,\"11\",\"3.3VA1\",,,\"←\",,\"J4014-11\",,\"3.3VA1\"
,\"12\",\"3.3VA1\",,,\"←\",,\"J4014-12\",,\"3.3VA1\"
,\"13\",\"3.3VA1\",,,\"←\",,\"J4014-13\",,\"3.3VA1\"
,\"14\",\"GND\",,,\"←\",,\"J4014-14\",,\"GND\"
,\"15\",\"GND\",,,\"←\",,\"J4014-15\",,\"GND\",,,,,,,,,,,\" \"
,\"J1021\",,,,,,,,,,,,,,,\"DC电源板的J4013\"
,\"1\",\"RMT-1\",,,,,,,,,,,,,\"←\",\"J4013-5\",,\"RMT-1\"
,\"2\",\"RMT-2\",,,,,,,,,,,,,\"←\",\"J4013-4\",,\"RMT-2\"
,\"3\",\"GND\",,,,,,,,,,,,,\"←\",\"J4013-3\",,\"GND\"
,,,,\"电源板(选购件)\",,,,\"J3502-1\",,\"←\",\"J9013M-1\",,\"J9013F-1\",,\"←\",\"J4013-2\",,\"REMOT\"
,,,,\"电源板(选购件)\",,,,\"J3502-2\",,\"←\",\"J9013M-2\",,\"J9013F-2\",,\"←\",\"J4013-1\",,\"GND\"
,\"J1022 \",,,,,,,,,,,,,,,\"NE复印数据处理控制卡板(选购件)\"
,,\"DC电源板\",,\"J4010-1\",,,\"→\",\"J5803-F2\",,\"J5803-M1\",,\"J9012-M8\",,\"J9012-F1\",,\"J1530-8\",,\"GND\"
,,\"DC电源板\",,\"J4010-2\",,,\"→\",\"J5803-F1\",,\"J5803-M2\",,\"J9012-M7\",,\"J9012-F2\",,\"J1530-7\",,\" 24V\"
,\"1\",\"GND\",,,,,\"→\",,,,,\"J9012-M6\",,\"J9012-F3\",,\"J1530-6\",,\"GND\"
,\"2\",\"RXD\",,\"数据接收\",,,\"←\",,,,,\"J9012-M5\",,\"J9012-F4\",,\"J1530-5\",,\"数据接收\"
,\"3\",\"TXD\",,\"数据发送\",,,\"→\",,,,,\"J9012-M4\",,\"J9012-F5\",,\"J1530-4\",,\"数据发送\"
,\"4\",\"COUNT\",,\"计数器\",,,\"→\",,,,,\"J9012-M3\",,\"J9012-F6\",,\"J1530-3\",,\"计数器\"
,\"5\",\"5V\",,,,,\"→\",,,,,\"J9012-M2\",,\"J9012-F7\",,\"J1530-2\",,\" 5\"
,\"6\",\"GND\",,,,,\"→\",,,,,\"J9012-M1\",,\"J9012-F8\",,\"J1530-1\",,\"GND\"
,\"7\"
,\"J1023\",,,,,,,,,,,,,,\"PCB20-J10\"
,\"1\",\"GND\",,,,,,,\"J9000-F10\",,\"J9000-M1\",,,,\"10\"
,\"2\",\"ZI ADDANROM CNCTN \",,,,,,,\"J9000-F9\",,\"J9000-M2\",,,,\"9\"
,\"3\",\"GND\",,,,,,,\"J9000-F8\",,\"J9000-M3\",,,,\"8\"
,\"4\",\"ZI ADDANROM DOUT\",,,,,,,\"J9000-F7\",,\"J9000-M4\",,,,\"7\"
,\"5\",\"ZO ADDANROM DIN\",,,,,,,\"J9000-F6\",,\"J9000-M5\",,,,\"6\"
,\"6\",\"GND\",,,,,,,\"J9000-F5\",,\"J9000-M6\",,,,\"5\"
,\"7\",\"ZO ADDANROM SCK\",,,,,,,\"J9000-F4\",,\"J9000-M7\",,,,\"4\"
,\"8\",\"ZO ADDANROM CS\",,,,,,,\"J9000-F3\",,\"J9000-M8\",,,,\"3\"
,\"9\",\"GND\",\" \",,,,,,\"J9000-F2\",,\"J9000-M9\",,,,\"2\"
,\"10\",\"5V\",,,,,,,\"J9000-F1\",,\"J9000-M10\",,,,\"1\"
,\"11\",,\" \"
,\"J1024\",,,,,,,,,,,,,,,,,,,\"投币机(选购件)\"
,,\"DC电源板\",,,\"J4011-1\",,\"→\",,\"J8502F-1\",,\"J8502M-1\",,\"→\",\"J1534M-12\",,,\"J1534F-1\",,\"→\",,\"GND\"
,,\"DC电源板\",,,\"J4011-2\",,\"→\",,\"J8502F-2\",,\"J8502M-2\",,\"→\",\"J1534M-11\",,,\"J1534F-2\",,\"→\",,\" 24V\"
,\"1\",\"GND\",,,,,\"→\",,,,,,,\"J1534M-10\",,,\"J1534F-3\",,\"→\"
,\"2\",\"RXD\",,,,,\"←\",,,,,,,\"J1534M-9\",,,\"J1534F-4\",,\"←\"
,\"3\",\"TXD\",,,,,\"→\",,,,,,,\"J1534M-8\",,,\"J1534F-5\",,\"→\"
,\"4\",\"COUNT\",,,,,\"→\",,,,,,,\"J1534M-7\",,,\"J1534F-6\",,\"→\"
,\"5\",\"5V\",,,,,\"→\",,,,,,,\"J1534M-6\",,,\"J1534F-7\",,\"→\"
,\"6\",\"GND\",,,,,\"→\",,,,,,,\"J1534M-5\",,,\"J1534F-8\",,\"→\"
,\"7\",\"COUNT\",,,,,\"→\",,,,,,,\"J1534M-4\",,,\"J1534F-9\",,\"→\"
,\"8\",\"DETECT\",,,,,\"←\",,,,,,,\"J1534M-3\",,,\"J1534F-10\",,\"←\"
,\"9\",\"5V\",,,,,\"→\",,,,,,,\"J1534M-2\",,,\"J1534F-11\",,\"→\"
,\"10\",\"GND\",,,,,\"→\",,,,,,,\"J1534M-1\",,,\"J1534F-12\",,\"→\"
,\"J1026\",,,,,,,,,,\"DC电源板(PCB2),J4016\"
,\"1\",\"5V\",,,,,\"←\",,\"J4016-1\",,\"5V\"
,\"2\",\"5V\",,,,,\"←\",,\"J4016-2\",,\"5V\"
,\"3\",\"GND\",,,,,\"←\",,\"J4016-3\",,\"GND\"
,\"4\",\"GND\",,,,,\"←\",,\"J4016-4\",,\"GND\"
,\"J1060\",,,,,,,,,,,,,,,,\"IV控制卡计数器板(选购件)\"
,\"1\",\"COUNT\",,,,,\"→\",\"J9016-F4\",,\"J9016-M1\",,,\"J1533-4\",,\"J1532-1\",,\"计数器驱动\"
,\"2\",\"CADE-DETECT\",,,,,\"←\",\"J9016-F3\",,\"J9016-M2\",,,\"J1533-3\",,\"J1532-2\",,\"计数器接入检测信号\"
,\"3\",\"5V\",,,,,\"→\",\"J9016-F2\",,\"J9016-M3\",,,\"J1533-2\",,\"J1532-3\",,\"计数器, 5\"
,\"4\",\"GND\",,,,,\"→\",\"J9016-F1\",,\"J9016-M4\",,,\"J1533-1\",,\"J1532-4\",,\"计数器接入检测信号,GND\"
,,,,,,,,,,\"DC电源板\"
,\"J9005-1 \",,\"中继板\",,\"3.3VA2\",,\"←\",\"J4017-1\",,\"3.3VA2\"
,\"J9005-2\",,\"中继板\",,\"3.3VA2\",,\"←\",\"J4017-2\",,\"3.3VA2\"
,\"J9005-3\",,\"中继板\",,\"3.3VA2\",,\"←\",\"J4017-3\",,\"3.3VA2\"
,\"J9005-4\",,\"中继板\",,\"3.3VA2\",,\"←\",\"J4017-4\",,\"3.3VA2\"
,\"J9005-5\",,\"中继板\",,\"3.3VA2\",,\"←\",\"J4017-5\",,\"3.3VA2\"
,\"J9005-6\",,\"中继板\",,\"GND\",,\"←\",\"J4017-6\",,\"GND\"
,\"J9005-7\",,\"中继板\",,\"GND\",,\"←\",\"J4017-7\",,\"GND\"
,\"J9005-8\",,\"中继板\",,\"GND\",,\"←\",\"J4017-8\",,\"GND\"
,\"J9005-9\",,\"中继板\",,\"GND\",,\"←\",\"J4017-9\",,\"GND\",,,,,,,\" \"
,\"J9005-10\",,\"中继板\",,\"GND\",,\"←\",\"J4017-10\",,\"GND\"
,,\"DC控制板(PCB1)\"
,\"J101\",,,,,,,,,\"DC电源板(PCB2)J4003\"
,\"1\",\"DCOM-24VU\",,,,,\"←\",\"J4003-1\",,\"DCOM-24VU\"
,\"2\",\"DCOM-0V\",,,,,\"←\",\"J4003-2\",,\"DCOM-0V\"
,\"3\",\"DCOM-12V\",,,,,\"←\",\"J4003-3\",,\"DCOM-12V\"
,\"4\",\"DCOM-GND\",,,,,\"←\",\"J4003-4\",,\"DCOM-GND\"
,\"5\",\"DCOM-5V\",,,,,\"←\",\"J4003-5\",,\"DCOM-5V\"
,\"6\",\"DCOM-0V\",,,,,\"←\",\"J4003-6\",,\"DCOM-0V\"
,\"7\",\"DCOM-3.3VA\",,,,,\"←\",\"J4003-7\",,\"DCOM-3.3VA\"
,\"8\",\"DCOM-0VU2\",,,,,\"←\",\"J4003-8\",,\"DCOM-0VU2\"
,\"J102A\",,,,,,,\"DC电源板冷却风扇\"
,1,\"GND\",,,,,\"→\",\"J4002-3\",,\"DC电源板冷却风扇GND\"
,2,\"FM6CLK\",,,,,\"←\",\"J4002-2\",,\"DC电源板冷却风扇FM6CLK同步信号\"
,3,\"FM6ON\",,,,,\"→\",\"J4002-1\",,\"DC电源板冷却风扇驱动信号FM6ON\",,,,,,,,,\"全速24V,半速12V\",,,,\"\\\"E804\\\"\"
,,,,,,,,\"高压电源板J4502\"
,4,\"PR-LEAK-DETECT\",,,,,\"←\",\"J4502-13\",,\"\\\"0\\\"一次高压漏电或电流过小\",,,,,,,,,,,,,\"\\\"E065\\\"\"
,5,\"TR-LEAK-DETECT\",,,,,\"←\",\"J4502-12\",,\"\\\"0\\\"转印高压漏电或电流过小\",,,,,,,,,,,,,\"\\\"E069\\\"\"
,6,\"PT/SP-LEAK-DETECT\",,,,,\"←\",\"J4502-11\",,\"\\\"0\\\"预转印/分离高压漏电或电流过小\"
,7,\"HV-CR-REMOTE\",,,,,\"→\",\"J4502-10\",,\"集尘辊偏压遥控信号,\\\"1\\\"集尘辊偏压ON\"
,8,\"DEV-DC-CNT(3～11V)\",,,,,\"→\",\"J4502-9\",,\"显影DC偏压输出控制信号\",,,,,,,,,\"(3～11V,ON 0～ 600V;12V以上OFF)\"
,9,\"DEV-AC-REMOTE\",,,,,\"→\",\"J4502-8\",,\"显影AC高压ON/OFF遥控信号\"
,10,\"HVT-HH-REMOTE\",,,,,\"→\",\"J4502-7\"
,11,\"PR-CNT(3～11V)\",,,,,\"→\",\"J4502-6\",,\"一次高压输出电流控制信号\",,,,,,,,,\"(3～11V,ON;12V以上OFF)\"
,12,\"TR-CNT(3～11V)\",,,,,\"→\",\"J4502-5\",,\"转印高压输出电流控制信号\",,,,,,,,,\"(3～11V,ON;12V以上OFF)\",,,,,,\"100～400微安\"
,13,\"PT/SP-CNT(3～11V)\",,,,,\"→\",\"J4502-4\",,\"预转印/分离高压输出电流控制信号\",,,,,,,,,\"(3～11V,ON;12V以上OFF)\",,,,,,\"0～-300微安\"
,14,\"SP-CNT(3～11V)\",,,,,\"→\",\"J4502-3\",,\"分离高压输出电流控制信号\",,,,,,,,,\"(3～11V,ON 8KVp-p～12KV;12V以上OFF)\"
,15,\"PT/SP-REMOTE\",,,,,\"→\",\"J4502-2\",,\"预转印/分离高压ON/OFF遥控信号\"
,16,\"PR/TR-REMOTE\",,,,,\"→\",\"J4502-1\",,\"一次/转印高压ON/OFF遥控信号\"
,\"J119\"
,4,\"GND\",,,,\"→\",,,\"J714F-1\",,\"→\",\"定影AC继电器线圈, 24\"
,3,\"FUSER RELAY 24V\",,,,\"←\",,,\"J714F-2\",,\"←\",\"定影AC继电器线圈,GND\"
,2,\"TEST 12V\",,,,,\"J704M-2\",,\"J704F-1 \",,\"TEST 12V\",,,\"→\",\"→\",\"→\",\"J703A-1\",,\"接FENSHER\"
,1,\"TEST GND\",,,,,\"J704M-1 \",,\"J704F-2\",,\"TEST GND\",,,\"→\",\"→\",\"→\",\"J703A-2\",,\"接FENSHER\"
,,,\"电源板PCB8(选购件)\"
,,,,\"J3504-4\",,\"→\",\"J707M-4\",,\"J707F-4\",,\"24V\",\"→\",\"→\",\"→\",\"→\",\"→\",\"J703C-4\"
,,,,\"J3504-3\",,\"→\",\"J707M-3\",,\"J707F-3\",,\"GND\",\"→\",\"→\",\"→\",\"→\",\"→\",\"J703C-3\"
,,,,,,,,,,,,,,,,,\"J703C-2\"
,,,,,,,,,,,,,,,,,\"J703C-1\"
,,,,\"J3504-2\",,\"→\",\"J707M-2\",,\"J707F-2\",,\"24V\",\"→\",\"→\",\"→\",\"→\",\"→\",\"J703A-7\"
,,,,\"J3504-1\",,\"→\",\"J707M-1\",,\"J707F-1\",,\"GND\",\"→\",\"→\",\"→\",\"→\",\"→\",\"J703A-6\"
,\"J102B\"
,1,\"未用\"
,2,\"FIN-TXD\",,,,\"→\",\"J701M-1\",,\"J701F-1\",,\"FIN-TXD\",,\"→\",\"→\",\"→\",\"→\",\"J703A-3\",,\"分页器(FINSHER)数据发送FIN-TXD\"
,3,\"FIN-RXD\",,,,\"←\",\"J701M-2\",,\"J701F-2\",,\"FIN-RXD\",,\"→\",\"→\",\"→\",\"→\",\"J703A-4\",,\"分页器(FINSHER)数据接收FIN-TXD\"
,4,\"0V\",,,,\"→\",\"J701M-3\",,\"J701F-3\",,\"0V\",,\"→\",\"→\",\"→\",\"→\",\"J703A-5\",,\"分页器(FINSHER)GND\"
,5,\" 24V\",,,,\"→\",\"J566M-2\",,\"J566F-1\",,\"→\",,,\"左前置纸仓(1500张)进纸电磁铁SL7, 24V\"
,6,\"LDPUSD/\",,,,\"→\",\"J566M-1\",,\"J566F-2\",,\"→\",,,\"左前置纸仓(1500张)进纸电磁铁SL7,驱动\"
,,,,,,,,,\"AC驱动板PCB3\",,,,,,,,,,,,\"鼓加热器控制板PCB7\"
,7,\"0V\",,,,\"→\",\"J2062-1\",,,,,,,,,,,,\"J2M-1\",,\"W1\",,\"J2002-1\",,\"鼓加热器温度检测热敏电阻HT-TEMP\"
,8,\"DRAM-HT-ON\",,,,\"→\",\"J2062-2\",,\"鼓加热器驱动\",,,,,\"J2053-1\",,,,,\"J2M-2\",,,,\"J2002-2\",,\"鼓加热器温度检测热敏电阻HT-TEMP\"
,9,\"SHRD/\",,,,\"→\",\"J2062-3\",,\"副定影灯ON驱动\",,,,,\"J2053-2\",,,,,\"J2M-3\",,\"W2\",,\"J2002-3\"
,10,\"SHSD\",,,,\"←\",\"J2062-4\",,\"副定影灯SSR检测\",,,,,\"J2053-3\",,,\" \",,,,,,\"J2002-4\",,\"鼓加热H3\"
,11,\"MHRD/\",,,,\"→\",\"J2062-5\",,\"主定影灯ON驱动\",,,,,\"J2053-4\",,,,,,,,,\"J2002-5\"
,12,\"MHSD\",,,,\"←\",\"J2062-6\",,\"主定影灯SSR检测\",,,,,,,,,,,,,,\"J2002-6\",,\"鼓加热H3\"
,13,\"CASSETTE-HT-ON\",,,,\"→\",\"J2062-7\",,\"纸盒加热器驱动\"
,14,\"12V\",,,,\"→\",\"J2062-8\",,,,,,,\"J2051-1\",,\"→\",\"→\",\"→\",\"→\",\"J1F-1\",,\"→\",\"J1M-1\"
,14,\"NC\",\"未用\",,,,,,,,,,,\"J2051-2\",,\"→\",\"→\",\"→\",\"→\",\"J1F-3\",,\"→\",\"J1M-3\"
,14,\"NC\",\"未用\",,,,,,,,,,,\"J2051-3\"
,,\"漏电保护继电器开关\"
,,,,\"BLCB\",,\"泸波器\",,,,\"继电器RL1触点\"
,,\"AC电源\",,,,,,,,,,,,,,,,,,\"J1F-2\",\"→\",\" J1M-2\",,\"副定影灯H2(600W)\"
,,\"→\",,,,,,,,,,,,\"定影温度保险开关TP1\"
,,\"→\",,,,,,,,,,,,,,,,,,\"J1F-4\",\"→\",\" J1M-4\",,\"主定影灯H1(600W)\"
,\"J103A\"
,\"1\",\"PTRCLM1\",,,\"→\",\"J103AM-1\",,,\"J103AF-1\",,\"J151M-2\",,\"J151F-1\",,\"J191M-2\",,\"J191F-1\",,\"预转印高压电极丝清洁电机M7,\\\"1\\\"电极丝清洁器向后移动\"
,\"2\",\"PTRCLM2\",,,\"→\",\"J103AM-2\",,,\"J103AF-2\",,\"J151M-1 \",,\"J151F-2\",,\"J191M-1\",,\"J191F-2\",,\"预转印高压电极丝清洁电机M7,\\\"1\\\"电极丝清洁器向后移动\"
,3,\" 24V\",,,\"→\",\"J103AM-3\",,,\"J103AF-3\",,\"J163M-4\",,\"J161F-1\",,\"J192M-3\",,\"J192F-1\",,\"预曝光灯LA1, 24V\"
,4,\"PEXP/\",,,\"→\",\"J103AM-4\",,,\"J103AF-4\",,\"J163M-3\",,\"J161F-2\",,\"J192M-2\",,\"J192F-2\"
,,,,,,,,,,,,,,,\"J192M-1\",,\"J192F-3\",,\"预曝光灯LA1驱动/\"
,5,\"PCLM1\",,,\"→\",\"J103AM-5\",,,\"J103AF-5\",,\"J163M-2\",,\"J161F-3\",,\"J193M-2\",,\"J193F-1\",,\"一次高压电极丝清洁电机M6,\\\"1\\\"电极丝清洁器向后移动\"
,6,\"PCLM2\",,,\"→\",\"J103AM-6\",,,\"J103AF-6\",,\"J163M-1\",,\"J161F-4\",,\"J193M-1\",,\"J193F-2\",,\"一次高压电极丝清洁电机M6,\\\"1\\\"电极丝清洁器向前移动\"
,7,\"5V\",,,\"→\",\"J103AM-7\",,,\"J103AF-7\",,\"J162M-3\",,\"J163F-1\",,\"→\",\"显影器墨粉检测传感器TS1, 5V\"
,8,\"DTEP\",,,\"←\",\"J103AM-8\",,,\"J103AF-8\",,\"J162M-2\",,\"J163F-2\",,\"←\",\"显影器墨粉检测传感器TS1信号保持\\\"0\\\"(缺粉)在0.3秒以上时驱动加粉电机M10\"
,9,\"0V\",,,\"→\",\"J103AM-9\",,,\"J103AF-9\",,\"J162M-1 \",,\"J163F-3\",,\"→\",\"显影器墨粉检测传感器TS1,GND\",,,,,,,,\"以ON 2秒OFF 1秒时序从粉仓向显影器加粉;\"
,10,\"FOOD\",,,\"←\",\"J103AM-10\",,,\"J103AF-10\",,\"J160M-2\",,\"J160F-1\",,,\"前门开关SW2打开检测\",,,,,,,,\"TS1信号保持\\\"1\\\"在0.7秒以上时停止加粉,\"
,11,\"0V\",,,\"→\",\"J103AM-11\",,,\"J103AF-11\",,\"J160M-1\",,\"J160F-2\",,,\"前门开关SW2打开检测,GND\",,,,,,,,\"TS1信号保持\\\"0\\\"在120秒以上时显示\\\"E020\\\"\"
,12,\"FM2CLK\",,,\"←\",\"J103AM-12\",,,\"J103AF-12\",,\"J161M-3\",,\"J161F-1\",,,\"一次充电冷却风扇FM2CLK同步信号\"
,13,\"0V\",,,\"→\",\"J103AM-13\",,,\"J103AF-13\",,\"J161M-2\",,\"J161F-2\",,,\"一次充电冷却风扇(FM2)GND\"
,14,\"FM2ON\",,,\"→\",\"J103AM-14\",,,\"J103AF-14\",,\"J161M-1\",,\"J161F-3\",,,\"一次充电冷却风扇(FM2)驱动信号\",,,,,,,,\"全速24V,半速12V\"
,15,\"NC\",\"未用\",,,\"J103AM-15\",,,\"J103AF-15\"
,\"J103B\",,,,,,,,,,,,,,,\"电位控制板(PCB6)\"
,1,\" 24V\",,,\"→\",\"J103BM-1\",,,\"J103BF-1\",,\"J9010M-1\",,\"J9010F-1\",,\"→\",\"J3-4\",\" 24V\"
,2,\"POT-ON\",,,\"→\",\"J103BM-2\",,,\"J103BF-2\",,\"J9010M-2\",,\"J9010F-2\",,\"→\",\"J3-3\",\"电位检测ON控制\",,,,\"→\",\"接电位传感器VS1\"
,3,\"POT-DT\",,,\"←\",\"J103BM-3\",,,\"J103BF-3\",,\"J9010M-3\",,\"J9010F-3\",,\"←\",\"J3-2\",\"电位检测值\"
,4,\"0V\",,,\"→\",\"J103BM-4\",,,\"J103BF-4\",,\"J9010M-4\",,\"J9010F-4\",,\"→\",\"J3-1\",\"GND\"
,5,\" 24V\",,,\"→\",\"J103BM-5\",,,\"J103BF-5\",,\"J153M-7\",,\"J153F-1\",,\"→\",\"J155M-2\",,\"J155F-1\",,\"加粉电机M10\"
,6,\"HVTM01/\",,,\"→\",\"J103BM-6\",,,\"J103BF-6\",,\"J153M-6\",,\"J153F-2\",,\"→\",\"J155M-1\",,\"J155F-2\",,\"加粉电机M10\"
,7,\" 24V\",,,\"→\",\"J103BM-7\",,,\"J103BF-7\",,\"J153M-5\",,\"J153F-3\",,\"→\",\"J158M-2\",,\"J158F-1\",,\"墨粉搅拌电机M9\"
,8,\"HVTM03/\",,,\"→\",\"J103BM-8\",,,\"J103BF-8\",,\"J153M-4\",,\"J153F-4\",,\"→\",\"J158M-1\",,\"J158F-2\",,\"墨粉搅拌电机M9\"
,9,\"5V\",,,\"→\",\"J103BM-9\",,,\"J103BF-9\",,\"J153M-3\",,\"J153F-5\",,\"→\",\"J156M-3\",,\"J156F-1\",,\"粉仓墨粉检测传感器TS2, 5V\"
,10,\"DTEP\",,,\"←\",\"J103BM-10\",,,\"J103BF-10\",,\"J153M-2\",,\"J153F-6\",,\"←\",\"J156M-2\",,\"J156F-2\",,\"粉仓墨粉检测传感器TS2信号保持\\\"0\\\"(缺粉)在1.9秒以上时加粉\"
,11,\"0V\",,,\"→\",\"J103BM-11\",,,\"J103BF-11\",,\"J153M-1\",,\"J153F-7\",,\"→\",\"J156M-1\",,\"J156F-3\",,\"粉仓墨粉检测传感器TS2,GND\",,,,,,,\"电机M10从粉仓向显影器加粉\"
,12,\"NC\",\"未用\",,,\"J103BM-12\",,,\"J103BF-12\",,\"J154M-4\",,\"J154F-1\",,,,\" \"
,13,\"0V\",,,\"→\",\"J103BM-13\",,,\"J103BF-13\",,\"J154M-3\",,\"J154F-2\",,\"→\",,\" \",\"J157-3\",,\"手送纸盘关闭传感器PS3\"
,14,\"MFDS\",,,\"←\",\"J103BM-14\",,,\"J103BF-14\",,\"J154M-2\",,\"J154F-3\",,\"←\",,,\"J157-2\",,\"手送纸盘关闭传感器PS3,\\\"1\\\"关闭\"
,15,\"5V\",,,\"→\",\"J103BM-15\",,,\"J103BF-15\",,\"J154M-1\",,\"J154F-4\",,\"→\",,,\"J157-1\",,\"手送纸盘关闭传感器PS3\"
,\"J104A\",,,,,\"接电机驱动板(PCB4)\"
,1,\"M11-A\",,,\"→\",\"J2101-A20\",,,\"J2102-1\",,\"M11-B/\",,\"J411M-1\",,\"J411F-6\",,\"右前置纸仓(1500张)进纸电机\"
,2,\"M11-A/\",,,\"→\",\"J2101-A19\",,,\"J2102-2\",,\" 24V\",,\"J411M-2\",,\"J411F-5\",,\"右前置纸仓(1500张)进纸电机\"
,3,\"M11-B\",,,\"→\",\"J2101-A18\",,,\"J2102-3\",,\"M11-B\",,\"J411M-3\",,\"J411F-4\",,\"右前置纸仓(1500张)进纸电机\"
,4,\"M11-B/\",,,\"→\",\"J2101-A17\",,,\"J2102-4\",,\"M11-A\",,\"J411M-4\",,\"J411F-3\",,\"右前置纸仓(1500张)进纸电机\"
,5,\" 24V\",,,\"→\",\"J2101-A16\",,,\"J2102-5\",,\" 24V\",,\"J411M-5\",,\"J411F-2\",,\"右前置纸仓(1500张)进纸电机\"
,6,\" 24V\",,,\"→\",\"J2101-A15\",,,\"J2102-6\",,\"M11-A/\",,\"J411M-6\",,\"J411F-1\",,\"右前置纸仓(1500张)进纸电机\"
,7,\"M12-A\",,,\"→\",\"J2101-A14\",,,\"J2104-1\",,\"M12-B/\",,,,,,\"前置纸盒3/4(550张)进纸电机\"
,8,\"M12-A/\",,,\"→\",\"J2101-A13\",,,\"J2104-2\",,\" 24V\",,,,,,\"前置纸盒3/4(550张)进纸电机\"
,9,\"M12-B\",,,\"→\",\"J2101-A12\",,,\"J2104-3\",,\"M12-B\",,,,,,\"前置纸盒3/4(550张)进纸电机\"
,10,\"M12-B/\",,,\"→\",\"J2101-A11\",,,\"J2104-4\",,\"M12-A\",,,,,,\"前置纸盒3/4(550张)进纸电机\"
,11,\" 24V\",,,\"→\",\"J2101-A10\",,,\"J2104-5\",,\" 24V\",,,,,,\"前置纸盒3/4(550张)进纸电机\"
,12,\" 24V\",,,\"→\",\"J2101-A9\",,,\"J2104-6\",,\"M12-A/\",,,,,,\"前置纸盒3/4(550张)进纸电机\"
,13,\"M17-A\",,,\"→\",\"J2101-A8\",,,\"J2102-13\",,\"M17-B/\",,\"J414M-1\",,\"J414F-6\",,\"预对位电机\"
,14,\"M17-A/\",,,\"→\",\"J2101-A7\",,,\"J2102-14\",,\" 24V\",,\"J414M-2\",,\"J414F-5\",,\"预对位电机\"
,15,\"M17-B\",,,\"→\",\"J2101-A6\",,,\"J2102-15\",,\"M17-B\",,\"J414M-3\",,\"J414F-4\",,\"预对位电机\"
,16,\"M17-B/\",,,\"→\",\"J2101-A5\",,,\"J2102-16\",,\"M17-A\",,\"J414M-4\",,\"J414F-3\",,\"预对位电机\"
,17,\" 24V\",,,\"→\",\"J2101-A4\",,,\"J2102-17\",,\" 24V\",,\"J414M-5\",,\"J414F-2\",,\"预对位电机\"
,18,\" 24V\",,,\"→\",\"J2101-A3\",,,\"J2102-18\",,\"M17-A/\",,\"J414M-6\",,\"J414F-1\",,\"预对位电机\"
,19,\"M24-A\",,,\"→\",\"J2101-A2\",,,\"J2103-1\",,\"M24-B/\",,\"J714M-6\",,\"J714F-1\",,\"左前置纸仓(1500张)进纸电机\"
,20,\"M24-A/\",,,\"→\",\"J2101-A1\",,,\"J2103-2\",,\" 24V\",,\"J714M-5\",,\"J714F-2\",,\"左前置纸仓(1500张)进纸电机\"
,\"J104B\",,,,,\"电机驱动板(PCB4)\"
,1,,\"M24-B\",,,\"J2101-B20\",,,\"J2103-3\",,\"M24-B\",,\"J714M-4\",,\"J714F-3\",,\"左前置纸仓(1500张)进纸电机\"
,2,,\"M24-B/\",,,\"J2101-B19\",,,\"J2103-4\",,\"M24-A\",,\"J714M-3\",,\"J714F-4\",,\"左前置纸仓(1500张)进纸电机\"
,3,,\" 24V\",,,\"J2101-B18\",,,\"J2103-5\",,\" 24V\",,\"J714M-2\",,\"J714F-5\",,\"左前置纸仓(1500张)进纸电机\"
,4,,\" 24V\",,,\"J2101-B17\",,,\"J2103-6\",,\"M24-A/\",,\"J714M-1\",,\"J714F-6\",,\"左前置纸仓(1500张)进纸电机\"
,5,,\"M27-A\",,,\"J2101-B16\",,,\"J2110-1\",,\"M27-B/\",,,,,,\"纵向输纸纸道的进纸电机\",,,,,,\"(下)\"
,6,,\"M27-A/\",,,\"J2101-B15\",,,\"J2110-2\",,\" 24V\",,,,,,\"纵向输纸纸道的进纸电机\",,,,,,\"(下)\"
,7,,\"M27-B\",,,\"J2101-B14\",,,\"J2110-3\",,\"M27-B\",,,,,,\"纵向输纸纸道的进纸电机\",,,,,,\"(下)\"
,8,,\"M27-B/\",,,\"J2101-B13\",,,\"J2110-4\",,\"M27-A\",,,,,,\"纵向输纸纸道的进纸电机\",,,,,,\"(下)\"
,9,,\" 24V\",,,\"J2101-B12\",,,\"J2110-5\",,\" 24V\",,,,,,\"纵向输纸纸道的进纸电机\",,,,,,\"(下)\"
,10,,\" 24V\",,,\"J2101-B11\",,,\"J2110-6\",,\"M27-A/\",,,,,,\"纵向输纸纸道的进纸电机\",,,,,,\"(下)\"
,11,,\"M26-A\",,,\"J2101-B10\",,,\"J2102-7\",,\"M26-B/\",,\"J412M-6\",,\"J412F-1\",,\"纵向输纸纸道的进纸电机\",,,,,,\"(上)\"
,12,,\"M26-A/\",,,\"J2101-B5\",,,\"J2102-8\",,\" 24V\",,\"J412M-5\",,\"J412F-2\",,\"纵向输纸纸道的进纸电机\",,,,,,\"(上)\"
,13,,\"M26-B\",,,\"J2101-B6\",,,\"J2102-9\",,\"M26-B\",,\"J412M-4\",,\"J412F-3\",,\"纵向输纸纸道的进纸电机\",,,,,,\"(上)\"
,14,,\"M26-B/\",,,\"J2101-B7\",,,\"J2102-10\",,\"M26-A\",,\"J412M-3\",,\"J412F-4\",,\"纵向输纸纸道的进纸电机\",,,,,,\"(上)\"
,15,,\" 24V\",,,\"J2101-B8\",,,\"J2102-11\",,\" 24V\",,\"J412M-2\",,\"J412F-5\",,\"纵向输纸纸道的进纸电机\",,,,,,\"(上)\"
,16,,\" 24V\",,,\"J2101-B9\",,,\"J2102-12\",,\"M26-A/\",,\"J412M-1\",,\"J412F-6\",,\"纵向输纸纸道的进纸电机\",,,,,,\"(上)\"
,17,,\"M25-A\",,,\"J2101-B4\",,,\"J2112-1\",,\"M25-B/\",,\"J413M-6\",,\"J413F-1\",,\"纵向输送/双面搬送电机M25\"
,18,,\"M25-A/\",,,\"J2101-B3\",,,\"J2112-2\",,\" 24V\",,\"J413M-5\",,\"J413F-2\",,\"纵向输送/双面搬送电机M25\"
,19,,\"M25-B\",,,\"J2101-B2\",,,\"J2112-3\",,\"M25-B\",,\"J413M-4\",,\"J413F-3\",,\"纵向输送/双面搬送电机M25\"
,20,,\"M25-B/\",,,\"J2101-B1\",,,\"J2112-4\",,\"M25-A\",,\"J413M-3\",,\"J413F-4\",,\"纵向输送/双面搬送电机M25\"
,\"J105\",,,,,\"接电机驱动板(PCB4)\"
,1,,\"M25, 24V\",,,\"J2108-13\",,,\"J2112-5\",,\" 24V\",,\"J413M-2\",,\"J413F-5\",,\"纵向输送/双面搬送电机M25\"
,2,,\"M25, 24V\",,,\"J2108-12\",,,\"J2112-6\",,\"M25-A/\",,\"J413M-1\",,\"J413F-6\",,\"纵向输送/双面搬送电机M25\"
,3,,\"RDPUSD/\",,,\"J2108-11\",,,\"J2105-1\",,\" 24V\",,\"J421M-2\",,\"J412F-1\",,\"右前置纸仓(1500张)进纸电磁铁SL6驱动/\"
,4,,\"M13 \",,,\"J2108-10\",,,\"J2105-2\",,\"RDPUSD/\",,\"J421M-1\",,\"J412F-2\",,\"右前置纸仓(1500张)进纸电磁铁SL6驱动/\"
,5,,\"M13 \",,,\"J2108-9\",,,\"J2105-3\",,\"LDLM\",,\"J419M-2\",,,,\"左前置纸仓(1500张)升纸电机M4\"
,6,,\"M13 \",,,\"J2108-8\",,,\"J2105-4\",,\"GND\",,\"J419M-1\",,,,\"左前置纸仓(1500张)升纸电机M4\"
,7,,\"M13 \",,,\"J2108-7\",,,\"J2105-5\",,\"RDLM\",,\"J418F-2\",,,,\"右前置纸仓(1500张)升纸电机M5\"
,8,,\"M13 \",,,\"J2108-6\",,,\"J2105-6\",,\"GND\",,\"J418F-1\",,,,\"右前置纸仓(1500张)升纸电机M5\"
,9,,\"M13 \",,,\"J2108-5\",,,,,,,\" \"
,10,,\"C4MLD(M21)\",,,\"J2108-4\",,,\"J2106-1\",,\"C3MLD\",,\"J810BM-3\",,\"J810BF-10\",,\"J804M-2\",,\"J804F-1\",,\"前置纸盒3(550张)升纸电机M20\"
,11,,\"C3MLD(M20)\",,,\"J2108-3\",,,\"J2106-2\",,\"GND\",,\"J810BM-4\",,\"J810BF-11\",,\"J804M-1\",,\"J804F-2\",,\"前置纸盒3(550张)升纸电机M20\"
,12,,\"LDLM(M4)\",,,\"J2108-2\",,,\"J2106-3\",,\"C4MLD\",,\"J810BM-5\",,\"J810BF-12\",,\"J805M-2\",,\"J805F-1\",,\"前置纸盒4(550张)升纸电机M21\"
,13,,\"RDLM(M5)\",,,\"J2108-1\",,,\"J2106-4\",,\"GND\",,\"J810BM-6\",,\"J810BF-13\",,\"J805M-1\",,\"J805F-2\",,\"前置纸盒4(550张)升纸电机M21\"
,,,,,,,,,,,,,\"DC电源板\"
,,,,,,,,,\"J2109-1\",,\"5V\",\"←\",\"J4009-1\",,\"5V\"
,,,,,,,,,\"J2109-2\",,\"0V\",\"←\",\"J4009-2\",,\"0V\"
,,,,,,,,,\"J2109-3\",,\"24V\",\"←\",\"J4009-3\",,\"24V\"
,,,,,,,,,\"J2109-4\",,\"0V\",\"←\",\"J4009-4\",,\"0V\"
,\"J106A\",,,,,,,,,,\"定影/搬送板(PCB23)\"
,1,\"FFUS\",,,\"J251AF-20\",,,\"J251AM-1\",,,\"J281-14\",,,\"J283-1\",,\"J252M-13\",,\"J252F-1\",,\"J254M-5\",,\"J254F-3\",,\"J261M-2\",,\"J261F-1\",,\"对位离合器CL2, 24V\"
,2,\"NC\",,,\"J251AF-19\",,,\"J251AM-2\",,,\"J281-13\",,,\"J283-2\",,\"J252M-12\",,\"J252F-2\",,\"J254M-4\",,\"J254F-4\",,\"J261M-1\",,\"J261F-2\",,\"对位离合器CL2驱动/\"
,3,\"RGPD\",,\"←\",\"J251AF-18\",,,\"J251AM-3\",,,\"J281-12\",,,\"J283-3\",,\"J252M-11\",,\"J252F-3\",,\"J254M-3\",,\"J254F-5\",,\"J262-1\",,\"对位传感器PS29, 5V\"
,4,\"NC\",,,\"J251AF-17\",,,\"J251AM-4\",,,\"J281-11\",,,\"J283-4\",,\"J252M-10\",,\"J252F-4\",,\"J254M-2\",,\"J254F-6\",,\"J262-2\",,\"对位传感器PS29\"
,5,\" 24V\",,,\"J251AF-16\",,,\"J251AM-5\",,,\"J281-10\",,,\"J283-5\",,\"J252M-9\",,\"J252F-5\",,\"J254M-1\",,\"J254F-7\",,\"J262-3\",,\"对位传感器PS29,GND\"
,6,\"RGCD/\",,,\"J251AF-15\",,,\"J251AM-6\",,,\"J281-9\",,,\"J283-6\",,\"J252M-8\",,\"J252F-6\",,\"J260M-2\",,\"J260F-1\",,\"转/分清洁电机M8,\\\"1\\\"电极丝清洁器向前移动\"
,7,\"TSCLM1\",,\"→\",\"J251AF-14\",,,\"J251AM-7\",,,\"J281-8\",,,\"J283-7\",,\"J252M-7\",,\"J252F-7\",,\"J260M-1\",,\"J260F-2\",,\"转/分清洁电机M8,\\\"1\\\"电极丝清洁器向后移动\"
,8,\"TSCLM2\",,\"→\",\"J251AF-13\",,,\"J251AM-8\",,,\"J281-7\",,,\"J283-8\",,\"J252M-6\",,\"J252F-8\",,\"J255M-3\",,\"J255F-1\",,\"定影入口导向板驱动电磁铁SL1, 24V\"
,9,\" 24V\",,,\"J251AF-12\",,,\"J251AM-9\",,,\"J281-6\",,,\"J283-9\",,\"J252M-5\",,\"J252F-9\",,\"J255M-2\",,\"J255F-2\",,\"定影入口导向板抬高驱动电磁铁SL1\"
,10,\"SL1P/\",,,\"J251AF-11\",,,\"J251AM-10\",,,\"J281-5\",,,\"J283-10\",,\"J252M-4\",,\"J252F-10\",,\"J255M-1\",,\"J255F-3\",,\"定影入口导向板降下驱动电磁铁SL1\"
,11,\"SL1R/\",,,\"J251AF-10\",,,\"J251AM-11\",,,\"J281-4\",,,\"J283-11\",,\"J252M-3\",,\"J252F-11\",,\"J271M-3\",,\"J271F-1\",,\"定影/搬送单元到位检测开关MSW3, 12V\"
,12,\" 12V\",,,\"J251AF-9\",,,\"J251AM-12\",,,\"J281-3\",,,\"J283-12\",,\"J252M-2\",,\"J252F-12\",,\"J271M-2\",,\"J271F-2\",,\"NC\"
,13,\" 24V\",,,\"J251AF-8\",,,\"J251AM-13\",,,\"J281-2\",,,\"J283-13\",,\"J252M-1\",,\"J252F-13\",,\"J271M-1\",,\"J271F-3\",,\"定影/搬送单元到位检测开关MSW3\"
,14,\"RVFSD1/\",,,\"J251AF-7\",,,\"J251AM-14\",,,\"J281-1\",,,\"J282A-6\",,\"J274F-8\",,\"J274M-1\",,\"J285M-1\",,\"J285F-2\",,\" 24V\",,\"定影排纸挡板(叉门)电磁铁SL5, 24V\"
,,,,,,,,,,,,,,\"J282A-7\",,\"J274F-7\",,\"J274M-2\",,\"J285M-2\",,\"J285F-1\",,\"RVFSD1/\",,\"定影排纸挡板(叉门)电磁铁SL5驱动\"
,\"J106A\"
,15,\"M13-B/\",,,\"J251AF-6\",,,\"J251AM-15\",,,\"→\",\"→\",\"→\",\"→\",\"→\",\"J286M-6\",,\"J286F-1\",,\"排纸电机M13\"
,16,\" 24V\",,,\"J251AF-5\",,,\"J251AM-16\",,,\"→\",\"→\",\"→\",\"→\",\"→\",\"J286M-5\",,\"J286F-2\",,\"排纸电机M13\"
,17,\"M13-B\",,,\"J251AF-4\",,,\"J251AM-17\",,,\"→\",\"→\",\"→\",\"→\",\"→\",\"J286M-4\",,\"J286F-3\",,\"排纸电机M13\"
,18,\"M13-A\",,,\"J251AF-3\",,,\"J251AM-18\",,,\"→\",\"→\",\"→\",\"→\",\"→\",\"J286M-3\",,\"J286F-4\",,\"排纸电机M13\"
,19,\" 24V\",,,\"J251AF-2\",,,\"J251AM-19\",,,\"→\",\"→\",\"→\",\"→\",\"→\",\"J286M-2\",,\"J286F-5\",,\"排纸电机M13\"
,20,\"M13-A/\",,,\"J251AF-1\",,,\"J251AM-20\",,,\"→\",\"→\",\"→\",\"→\",\"→\",\"J286M-1\",,\"J286F-6\",,\"排纸电机M13\"
,,,,,,,,,,,,,,\"J289-1\",,\"→\",\"J611-1\",,\" 24V\",,,,\"←\",\"定影电机M19驱动板\"
,\"J106B\",,,,,,,,,,,,,\"J289-2\",,\"→\",\"J611-2\",,\"GND\"
,1,\"IDS\",,,\"J251BF-20\",,,\"J251BM-1\",,,\"J287-20\",,,\"J282A-1\",,\"→\"
,2,\"DSJAM\",,,\"J251BF-19\",,,\"J251BM-2\",,,\"J287-19\",,,\"J282A-2\",,\"←\",\"J612-4\",,\"M19LD\",,,,\"(电机达到规定转速时M19LD=0)\"
,3,\" 24V\",,,\"J251BF-18\",,,\"J251BM-3\",,,\"J287-18\",,,\"J282A-3\",,\"→\",\"J612-3\",,\"M19ON\",,,,\"定影电机M19启动信号\"
,4,\"FCBSD/\",,,\"J251BF-17\",,,\"J251BM-4\",,,\"J287-17\",,,\"J282A-4\",,\"→\",\"J612-2\",,\"5V\"
,5,\"CBOP\",,,\"J251BF-16\",,,\"J251BM-5\",,,\"J287-16\",,,\"J282A-5\",,\"→\",\"J612-1\",,\"GND\"
,6,\"NC\",,,\"J251BF-15\",,,\"J251BM-6\",,,\"J287-15\",,,\"J288-1\",,\"J251CM-3\",,\"J251CF-3\",,,,\"←\",\"J1415F-3\",,\"J1415M-3\",,\"J903-7\",,\"定影电机M19, 24VU\"
,7,\"M-TEMP\",,\"←\",\"J251BF-14\",,,\"J251BM-7\",,,\"J287-14\",,,\"J288-2\",,\"J251CM-4\",,\"J251CF-4\",,\"J251CF-4\",,\"←\",\"J321M-2\",,\"J321F-2\",,,,\"定影电机M19,GND\"
,8,\"0V\",,\"→\",\"J251BF-13\",,,\"J251BM-8\",,,\"J287-13\",,,\"J282A-8\",,\"J274F-6\",,\"J274M-3\",,\"J273-3\",,\"排纸部卡纸传感器PS46,GND\"
,9,\"S-TEMP\",,\"←\",\"J251BF-12\",,,\"J251BM-9\",,,\"J287-12\",,,\"J282A-9\",,\"J274F-5\",,\"J274M-4\",,\"J273-2\",,\"排纸部卡纸传感器PS46,DSJAM\"
,10,\"0V\",,\"→\",\"J251BF-11\",,,\"J251BM-10\",,,\"J287-11\",,,\"J282A-10\",,\"J274F-4\",,\"J274M-5\",,\"J273-1\",,\"排纸部卡纸传感器PS46, 24V\"
,11,\"FM5CLK\",,,\"J251BF-10\",,,\"J251BM-11\",,,\"J287-10\",,,\"J282A-11\",,\"J274F-3\",,\"J274M-6\",,\"J259-1\",,\"外排纸卡纸传感器PS36, 5V\"
,12,\"0V\",,,\"J251BF-9\",,,\"J251BM-12\",,,\"J287-9\",,,\"J282A-12\",,\"J274F-2\",,\"J274M-7\",,\"J259-2\",,\"外排纸卡纸传感器PS36,EDS\"
,13,\"FM5ON\",,,\"J251BF-8\",,,\"J251BM-13\",,,\"J287-8\",,,\"J282A-13\",,\"J274F-1\",,\"J274M-8\",,\"J259-3\",,\"外排纸卡纸传感器PS36,GND\"
,14,\"NC未用\",,,\"J251BF-7\",,,\"J251BM-14\",,,\"J287-7\",,,\"J282B-1\",,\"J253M-10\",,\"J253F-1\",,\"J263F-2\",,\"J263M-1\",,\"定影清洁纸电磁铁SL9, 24V\"
,15,\"M19LD\",,\"←\",\"J251BF-6\",,,\"J251BM-15\",,,\"J287-6\",,,\"J282B-2\",,\"J253M-9\",,\"J253F-2\",,\"J263F-1\",,\"J263M-2\",,\"定影清洁纸电磁铁SL9驱动/,FCBSD/\"
,16,\"M19ON\",,,\"J251BF-5\",,,\"J251BM-16\",,,\"J287-5\",,,\"J282B-3\",,\"J253M-8\",,\"J253F-3\",,,,\"J264-3\",,\"定影清洁卷筒纸余量传感器PS45,GND\"
,17,\"5V\",,,\"J251BF-4\",,,\"J251BM-17\",,,\"J287-4\",,,\"J282B-4\",,\"J253M-7\",,\"J253F-4\",,,,\"J264-2\",,\"定影清洁卷筒纸余量传感器PS45,CBOP\"
,18,\"GND\",,,\"J251BF-3\",,,\"J251BM-18\",,,\"J287-3\",,,\"J282B-5\",,\"J253M-6\",,\"J253F-5\",,,,\"J264-1\",,\"定影清洁卷筒纸余量传感器PS45, 5V\"
,19,\"CJAM\",,,\"J251BF-2\",,,\"J251BM-19\",,,\"J287-2\",,,\"J282B-6\",,\"J253M-5\",,\"J253F-6\",,\"J265F-3\",,\"J265M-1\",,\"主定影灯温度检测热敏电阻TH1\"
,20,\"EDS\",,,\"J251BF-1\",,,\"J251BM-20\",,,\"J287-1\",,,\"J282B-7\",,\"J253M-4\",,\"J253F-7\",,\"J265F-2\",,\"J265M-2\"
,,,,,,,,,,,,,,\"J282B-8\",,\"J253M-3\",,\"J253F-8\",,\"J265F-1\",,\"J265M-3\",,\"主定影灯温度检测热敏电阻TH1\"
,,,,,,,,,,,,,,\"J282B-9\",,\"J253M-2\",,\"J253F-9\",,\"J267F-2\",,\"J267M-1\",,\"副定影灯温度检测热敏电阻TH2\"
,,,,,,,,,,,,,,\"J282B-10\",,\"J253M-1\",,\"J253F-10\",,\"J267F-1\",,\"J267M-2\",,\"副定影灯温度检测热敏电阻TH2\"
,,,,,,,,,,,,,,\"J282B-11\",,\"J270M-1\",,\"J270F-1\",,,,,,\"去除卷曲纸风扇的FM5CLK同步信号\"
,,,,,,,,,,,,,,\"J282B-12\",,\"J270M-2\",,\"J270F-2\",,,,,,\"去除卷曲纸风扇(FM5),0V\"
,,,,,,,,,,,,,,\"J282B-13\",,\"J270M-3\",,\"J270F-3\",,,,,,\"去除卷曲纸风扇(FM5)ON信号\"
,,,,,,,,,,,,,,\"J284-1\",,\"J256-3\",,\"定影分离爪卡纸传感器PS4,GND\"
,,,,,,,,,,,,,,\"J284-2\",,\"J256-2\",,\"定影分离爪卡纸传感器PS4,CJAM\"
,,,,,,,,,,,,,,\"J284-3\",,\"J256-1\",,\"定影分离爪卡纸传感器PS4,5V\"
,,,,,,,,,,,,,,\"J286-1\",,\"J257-3\",,\"内排纸检测传感器PS35,GND\"
,,,,,,,,,,,,,,\"J286-2\",,\"J257-2\",,\"内排纸检测传感器PS35,IDS\"
,\"J118\",,\"接定影/搬送板(PCB23),J285\",,,,,,,,,,,\"J286-3\",,\"J257-1\",,\"内排纸检测传感器PS35, 5V\"
,1,\"GND\",,,\"→\",\"J251CF-1\",,\"J251CM-1\",,\"GND\",\"J285-2\",,,\"J286-4\"
,2,\" 5V\",,,\"→\",\"J251CF-2\",,\"J251CM-2\",,\" 5V\",\"J285-1\"
,\"J107A\",,,,,,,,,,\"双面驱动板(PCB9)\"
,1,\"M16-A/\",,,\"J222AF-16\",,,\"J222AM-1\",,,\"J2302-A16\",,,\"J2301-1\",,\"J222MC-1\",,\"J222FC-1\",,\"J232F-1\",,\"J232M-4\",,\"J1414F-1\",,\"←\",\"GND\"
,2,\"M18-A\",,,\"J222AF-15\",,,\"J222AM-2\",,,\"J2302-A15\",,,\"J2301-2\",,\"J222MC-2\",,\"J222FC-2\",,\"J232F-2\",,\"J232M-3\",,\"J1414F-2\",,\"←\",\"TRAY-24V\"
,3,\"M18-B/\",,,\"J222AF-14\",,,\"J222AM-3\",,,\"J2302-A14\",,,\"J2301-3\",,\"J222MC-3\",,\"J222FC-3\",,\"J232F-3\",,\"J232M-2\",,\"J4004-2\",,\"←\",\" 5V\"
,4,\"M18-B\",,,\"J222AF-13\",,,\"J222AM-4\",,,\"J2302-A13\",,,\"J2301-4\",,\"J222MC-4\",,\"J222FC-4\",,\"J232F-4\",,\"J232M-1\",,\"J4004-1\",,\"←\",\"GND\"
,5,\"M18-A/\",,,\"J222AF-12\",,,\"J222AM-5\",,,\"J2302-A12\",,,\"J2303-1\",,\"J232M-3\",,\"J232F-1\",,\"双面搬送风扇的FM8驱动信号\"
,6,\" 24V\",,,\"J222AF-11\",,,\"J222AM-6\",,,\"J2302-A11\",,,\"J2303-2\",,\"J232M-2\",,\"J232F-2\",,\"双面搬送风扇的FM8CLK同步信号\"
,7,\" 24V\",,,\"J222AF-10\",,,\"J222AM-7\",,,\"J2302-A10\",,,\"J2303-3\",,\"J232M-1\",,\"J232F-3\",,\"双面搬送风扇的FM8,GND\"
,8,\"M29-A\",,,\"J222AF-9\",,,\"J222AM-8\",,,\"J2302-A9\",,,\"J2305-1\",,\"J231M-6\",,\"J231F-1\",,\"双面纸盘右搬送电机M18\",,,,,\"M18-B/\"
,9,\"M29-A/\",,,\"J222AF-8\",,,\"J222AM-9\",,,\"J2302-A8\",,,\"J2305-2\",,\"J231M-5\",,\"J231F-2\",,\"双面纸盘右搬送电机M18\",,,,,\" 24V\"
,10,\"M29-B\",,,\"J222AF-7\",,,\"J222AM-10\",,,\"J2302-A7\",,,\"J2305-3\",,\"J231M-4\",,\"J231F-3\",,\"双面纸盘右搬送电机M18\",,,,,\"M18-B\"
,11,\"M29-B/\",,,\"J222AF-6\",,,\"J222AM-11\",,,\"J2302-A6\",,,\"J2305-4\",,\"J231M-3\",,\"J231F-4\",,\"双面纸盘右搬送电机M18\",,,,,\"M18-A\"
,12,\" 24V\",,,\"J222AF-5\",,,\"J222AM-12\",,,\"J2302-A5\",,,\"J2305-5\",,\"J231M-2\",,\"J231F-5\",,\"双面纸盘右搬送电机M18\",,,,,\" 24V\"
,13,\" 24V\",,,\"J222AF-4\",,,\"J222AM-13\",,,\"J2302-A4\",,,\"J2305-6\",,\"J231M-1\",,\"J231F-6\",,\"双面纸盘右搬送电机M18\",,,,,\"M18-A/\"
,14,\"FM8ON\",,,\"J222AF-3\",,,\"J222AM-14\",,,\"J2302-A3\",,,\"J2305-7\",,\"J228M-6\",,\"J228F-1\",,\"双面反转电机M14\",,,,,\"M14-B/\"
,14.7,\"FM8CLK\",,,\"J222AF-2\",,,\"J222AM-15\",,,\"J2302-A2\",,,\"J2305-8\",,\"J228M-5\",,\"J228F-2\",,\"双面反转电机M14\",,,,,\" 24V\"
,16.1,\"LDPFS\",,,\"J222AF-1\",,,\"J222AM-16\",,,\"J2302-A1\",,,\"J2305-9\",,\"J228M-4\",,\"J228F-3\",,\"双面反转电机M14\",,,,,\"M14-B\"
,,,,,,,,,,,,,,\"J2305-10\",,\"J228M-3\",,\"J228F-4\",,\"双面反转电机M14\",,,,,\"M14-A\"
,,,,,,,,,,,,,,\"J2305-11\",,\"J228M-2\",,\"J228F-5\",,\"双面反转电机M14\",,,,,\" 24V\"
,,,,,,,,,,,,,,\"J2305-12\",,\"J228M-1\",,\"J228F-6\",,\"双面反转电机M14\",,,,,\"M14-A/\"
,,,,,,,,,,,,,,\"J2305-13\",,\"J226M-1\",,\"J226F-1\",,\"双面输纸反转辊传感器1 PS37,GND\"
,,,,,,,,,,,,,,\"J2305-14\",,\"J226M-2\",,\"J226F-2\",,\"双面输纸反转辊传感器1 PS37,RVS1\"
,,,,,,,,,,,,,,\"J2305-15\",,\"J226M-3\",,\"J226F-3\",,\"双面输纸反转辊传感器1 PS37, 5V\"
,,,,,,,,,,,,,,,,\"J226M-4\",,\"J226F-4\"
,16.8,\"WTFL/\",,,,\"J712M-2\",,\"J712F-1\",,\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"废粉螺杆异常,废粉锁定传感器(MSW1)\",,,,,,,,\"MSW1,\\\"0\\\"达4秒以上显示\\\"E013\\\"\"
,17.5,\"GND\",,,,\"J712M-1\",,\"J712F-2\",,\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"→\",\"废粉螺杆异常,废粉锁定传感器(MSW1)开关GND\"
,\"J107B\",,,,,,,,,,\"双面驱动板(PCB9)\"
,1,\"M16-B/相\",,,,\"J222BF-16\",,\"J222BM-1\",,,\"J2302-B16\",,,\"J2306A-1\",,\"J229F-9\",,\"J229M-1\",,\"J1518-1\",,\"双面横向对位传感器PS31,GND\"
,2,\"M14-A\",,,,\"J222BF-15\",,\"J222BM-2\",,,\"J2302-B15\",,,\"J2306A-2\",,\"J229F-8\",,\"J229M-2\",,\"J1518-2\",,\"双面横向对位传感器PS31,DSRGPD\"
,3,\"M14-A/\",,,,\"J222BF-14\",,\"J222BM-3\",,,\"J2302-B14\",,,\"J2306A-3\",,\"J229F-7\",,\"J229M-3\",,\"J1518-3\",,\"双面横向对位传感器PS31, 5V\"
,4,\"M14-B\",,,,\"J222BF-13\",,\"J222BM-4\",,,\"J2302-B13\",,,\"J2306A-4\",,\"J229F-6\",,\"J229M-4\",,\"J230M-6\",,\"J230F-1\",,\"双面横向对位电机M16\",,,,,\" 24V\"
,5,\"M14-B/\",,,,\"J222BF-12\",,\"J222BM-5\",,,\"J2302-B12\",,,\"J2306A-5\",,\"J229F-5\",,\"J229M-5\",,\"J230M-5\",,\"J230F-2\",,\"双面横向对位电机M16\",,,,,\" 24V\"
,6,\" 24V\",,,,\"J222BF-11\",,\"J222BM-6\",,,\"J2302-B11\",,,\"J2306A-6\",,\"J229F-4\",,\"J229M-6\",,\"J230M-4\",,\"J230F-3\",,\"双面横向对位电机M16\",,,,,\"M16-A相\"
,7,\" 24V\",,,,\"J222BF-10\",,\"J222BM-7\",,,\"J2302-B10\",,,\"J2306A-7\",,\"J229F-3\",,\"J229M-7\",,\"J230M-3\",,\"J230F-4\",,\"双面横向对位电机M16\",,,,,\"M16-A/相\"
,8,\"M16-A相\",,,,\"J222BF-9\",,\"J222BM-8\",,,\"J2302-B9\",,,\"J2306A-8\",,\"J229F-2\",,\"J229M-8\",,\"J230M-2\",,\"J230F-5\",,\"双面横向对位电机M16\",,,,,\"M16-B相\"
,9,\"M16-B相\",,,,\"J222BF-8\",,\"J222BM-9\",,,\"J2302-B8\",,,\"J2306A-9\",,\"J229F-1\",,\"J229M-9\",,\"J230M-1\",,\"J230F-6\",,\"双面横向对位电机M16\",,,,,\"M16-B/相\"
,10,\" 24V\",,,,\"J222BF-7\",,\"J222BM-10\",,,\"J2302-B7\",,,\"J2306A-10\",,,,,,,,\"J227-1\",,\"左前置纸仓(1500张)进纸传感器PS33,GND\"
,11,\"RVFSD2/\",,,,\"J222BF-6\",,\"J222BM-11\",,,\"J2302-B6\",,,\"J2306A-11\",,,,,,,,\"J227-2\",,\"左前置纸仓(1500张)进纸传感器PS33,LDPFS\"
,12,\"DSRGPD\",,,,\"J222BF-5\",,\"J222BM-12\",,,\"J2302-B5\",,,\"J2306A-12\",,,,,,,,\"J227-3\",,\"左前置纸仓(1500张)进纸传感器PS33, 5V\"
,13,\"DGRFPC\",,,,\"J222BF-4\",,\"J222BM-13\",,,\"J2302-B4\",,,\"J2306B-1\",,\"J223M-5\",,\"J223F-1\",,\"J225F-3\",,\"J225M-1\",,\"J1516-1\",,\"双面输纸反转辊传感器2 PS38,GND\"
,14,\"DPDS\",,,,\"J222BF-3\",,\"J222BM-14\",,,\"J2302-B3\",,,\"J2306B-2\",,\"J223M-4\",,\"J223F-2\",,\"J225F-2\",,\"J225M-2\",,\"J1516-2\",,\"双面输纸反转辊传感器2 PS38,RVS2\"
,14.7,\"RVS1\",,,,\"J222BF-2\",,\"J222BM-15\",,,\"J2302-B2\",,,\"J2306B-3\",,\"J223M-3\",,\"J223F-3\",,\"J225F-1\",,\"J225M-3\",,\"J1516-3\",,\"双面输纸反转辊传感器2 PS38\"
,\"16\",\"RVS2\",,,,\"J222BF-1\",,\"J222BM-16\",,,\"J2302-B1\",,,\"J2306B-4\",,\"J223M-2\",,\"J223F-4\",,\"J224F-1\",,\"J224M-2\",,,,\"双面反转电磁铁SL8, 24V\"
,16.8,\"NC未用\",,,,,,,,,,,,\"J2306B-5\",,\"J223M-1\",,\"J223F-5\",,\"J224F-2\",,\"J224M-1\",,,,\"双面反转电磁铁SL8,驱动/\"
,17.5,\"NC未用\",,,,,,,,,,,,\"J2306B-6\",,\"J234M-6\",,\"J234F-1\",,\"J235-3\",,\"双面纸盘(单张纸盘)纸张传感器PS34,GND\"
,,,,,,,,,,,,,,\"J2306B-7\",,\"J234M-5\",,\"J234F-2\",,\"J235-2\",,\"双面纸盘(单张纸盘)纸张传感器PS34,DPDS\"
,,,,,,,,,,,,,,\"J2306B-8\",,\"J234M-4\",,\"J234F-3\",,\"J235-1\",,\"双面纸盘(单张纸盘)纸张传感器PS34, 5V\"
,,,,,,,,,,,,,,\"J2306B-9\",,\"J234M-3\",,\"J234F-4\",,\"J236-3\",,\"双面纸盘(单张纸盘)纸张预对位传感器PS30,GND\"
,,,,,,,,,,,,,,\"J2306B-10\",,\"J234M-2\",,\"J234F-5\",,\"J236-2\",,\"双面纸盘(单张纸盘)纸张预对位传感器PS30,DGRFPC\"
,,,,,,,,,,,,,,\"J2306B-11\",,\"J234M-1\",,\"J234F-6\",,\"J236-1\",,\"双面纸盘(单张纸盘)纸张预对位传感器PS30, 5V\"
,,,,,,,,,,,,,,\"J2306B-12\"
,,,,,,,,,,,,,,\"J2307-1\",,\"J233M-6\",,\"J233F-1\",,\"M29-B/\",,\"双面纸盘左搬送电机M29\"
,,,,,,,,,,,,,,\"J2307-2\",,\"J233M-5\",,\"J233F-2\",,\" 24V\",,\"双面纸盘左搬送电机M29\"
,,,,,,,,,,,,,,\"J2307-3\",,\"J233M-4\",,\"J233F-3\",,\"M29-B/\",,\"双面纸盘左搬送电机M29\"
,,,,,,,,,,,,,,\"J2307-4\",,\"J233M-3\",,\"J233F-4\",,\"M29-A\",,\"双面纸盘左搬送电机M29\"
,,,,,,,,,,,,,,\"J2307-5\",,\"J233M-2\",,\"J233F-5\",,\" 24V\",,\"双面纸盘左搬送电机M29\"
,,,,,,,,,,,,,,\"J2307-6\",,\"J233M-1\",,\"J233F-6\",,\"M29-A/\",,\"双面纸盘左搬送电机M29\"
,\"J108A\",,,,\"接主电机;鼓电机板\"
,1,,\"NC未用\"
,2,,\"FM4ON\",,,,\"J713M-3\",,\"J713F-1\",,\"控制部冷却风扇(FM4)驱动信号\"
,3,,\"GND\",,,,\"J713M-2\",,\"J713F-2\",,\"控制部冷却风扇(FM4)GND\"
,4,,\"FM4CLK\",,,,\"J713M-1\",,\"J713F-3\",,\"FM4CLK同步信号\"
,,,,,,,,,,,,,\"主电机M2电路板\"
,5,,\"MMFG\",,\"←\",,\"J6320M-4\",,\"J6320F-1\",,\"J632-4\",,\"主电机M2旋转时钟信号\",,,,,\"J631-1\",,\"←\",\"J903-5\",,\"J903-9\",,\"J4005-1\",,\" 24V\"
,6,,\"MMON\",,\"→\",,\"J6320M-3\",,\"J6320F-2\",,\"J632-3\",,\"主电机M2驱动信号\",,,,,\"J631-2\",,\"←\",\"J4005-2\",,,,,,\"GND\"
,7,,\"5V\",,\"→\",,\"J6320M-2\",,\"J6320F-3\",,\"J632-2\"
,8,,\"0V\",,\"→\",,\"J6320M-1\",,\"J6320F-4\",,\"J632-1\"
,,,,,,,,,,,,,\"鼓电机M1电路板\"
,9,,\"DMFG\",,,,,,,,\"J602-4\",,\"鼓电机M1旋转时钟信号\",,,,,\"J601-1\",,\"←\",\"J903-6\",,\" 24V\"
,10,,\"DMON\",,,,,,,,\"J602-3\",,\"鼓电机M1驱动信号\",,,,,\"J601-2\",,\"←\",\"J4005-2\",,,,,,\"GND\"
,11,,\"5V\",,,,,,,,\"J602-2\"
,12,,\"0V\",,,,,,,,\"J602-1\"
,\"J108B\",,,,\"接手送纸盘;显影离合器CL1\"
,1,,\" 24V\",,,,,,,,\"J715M-2\",,\"J715F-1\",,\"显影离合器CL1, 24V\"
,2,,\" DEVCD/\",,,,,,,,\"J715M-1\",,\"J715F-2\",,\"显影离合器CL1,驱动/,DEVCD/\"
,3,,\" 24V\",,,,,,,,\"J725M-1\",,\"J725F-1\",,\"手送纸离合器CL3, 24V\"
,4,,\"MFPCD/\",,,,,,,,\"J725M-2\",,\"J725F-2\",,\"手送纸离合器CL3,驱动/,MFPCD/\"
,5,,\"0V\",,,\"J726M-8\",,\"J726F-1\",,,\"J727M-3\",,\"J727F-1\",,\"手送纸宽度检测电位器SVR1\",,,,,,\"0V\"
,6,,\"MFPD\",,,\"J726M-7\",,\"J726F-2\",,,\"J727M-2\",,\"J727F-2\",,\"手送纸宽度检测电位器SVR1\",,,,,,\"MFPD\"
,7,,\" 5V\",,,\"J726M-6\",,\"J726F-3\",,,\"J727M-1\",,\"J727F-3\",,\"手送纸宽度检测电位器SVR1\",,,,,,\" 5V\"
,8,,\"0V\",,,\"J726M-5\",,\"J726F-4\",,,,,\"J728-3\",,\"手送纸盘有纸传感器PS23\",,,,,,\"0V\"
,9,,\"MFDS\",,,\"J726M-4\",,\"J726F-5\",,,,,\"J728-2\",,\"手送纸盘有纸传感器PS23\",,,,,,\"MFDS\"
,10,,\" 5V\",,,\"J726M-3\",,\"J726F-6\",,,,,\"J728-1\",,\"手送纸盘有纸传感器PS23\",,,,,,\" 5V\"
,11,,\" 24V\",,,\"J726M-2\",,\"J726F-7\",,,\"J729M-2\",,\"J729F-1\",,\"手送纸解除电磁铁SL2\",,,,,,\" 24V\"
,12,,\"MFLSD/\",,,\"J726M-1\",,\"J726F-8\",,,\"J729M-1\",,\"J729F-2\",,\"手送纸解除电磁铁SL2,驱动/\"
,\"J109\",,,,\"接搬送风扇(FM1)\"
,1,,\"MF1ON\",,,\"搬送风扇(FM1)驱动信号\"
,2,,\"0V\",,,\"搬送风扇(FM1)GND\"
,3,,\"MF1CLK\",,,\"搬送风扇FM1CLK同步信号\"
,\"J110A\",,,,\"接前置纸盒3(550张)\"
,1,,\"0V\",,,\"J531AM-9\",,,\"J531AF-1\",,,\"J532-3\",,\"前置纸盒3(550张)升纸传感器PS17\",,,,,,,\"0V\"
,2,,\"C3LTP\",,,\"J531AM-8\",,,\"J531AF-2\",,,\"J532-2\",,\"前置纸盒3(550张)升纸传感器PS17\",,,,,,,\"C3LTP\"
,3,,\" 5V\",,,\"J531AM-7\",,,\"J531AF-3\",,,\"J532-1\",,\"前置纸盒3(550张)升纸传感器PS17\",,,,,,,\" 5V\"
,4,,\"0V\",,,\"J531AM-6\",,,\"J531AF-4\",,,\"J533-3\",,\"前置纸盒3(550张)纸检测传感器PS13\",,,,,,,\"0V\"
,5,,\"C3PD\",,,\"J531AM-5\",,,\"J531AF-5\",,,\"J533-2\",,\"前置纸盒3(550张)纸检测传感器PS13\",,,,,,,\"C3PD\"
,6,,\" 5V\",,,\"J531AM-4\",,,\"J531AF-6\",,,\"J533-1\",,\"前置纸盒3(550张)纸检测传感器PS13\",,,,,,,\" 5V\"
,7,,\"0V\",,,\"J531AM-3\",,,\"J531AF-7\",,,\"J534-3\",,\"前置纸盒3(550张)重新进纸传感器PS21\",,,,,,,\"0V\"
,8,,\"C3RTD\",,,\"J531AM-2\",,,\"J531AF-8\",,,\"J534-2\",,\"前置纸盒3(550张)重新进纸传感器PS21\",,,,,,,\"C3RTD\"
,9,,\"5V\",,,\"J531AM-1\",,,\"J531AF-9\",,,\"J534-1\",,\"前置纸盒3(550张)重新进纸传感器PS21\",,,,,,,\"5V\"
,10,,\"0V\",,,\"J531BM-9\",,,\"J531BF-1\",,,\"J535-3\",,\"前置纸盒3(550张)关闭传感器PS15\",,,,,,,\"0V\"
,11,,\"C3OP\",,,\"J531BM-8\",,,\"J531BF-2\",,,\"J535-2\",,\"前置纸盒3(550张)关闭传感器PS15\",,,,,,,\"C3OP\"
,12,,\"5V\",,,\"J531BM-7\",,,\"J531BF-3\",,,\"J535-1\",,\"前置纸盒3(550张)关闭传感器PS15\",,,,,,,\"5V\"
,13,,\"GND\",,,\"J531BM-6\",,,\"J531BF-4\",,,\"J536-3\",,\"纵向输纸纸道的输纸传感器3 PS26\",,,,,,,\"GND\"
,14,,\"VP3PD\",,,\"J531BM-5\",,,\"J531BF-5\",,,\"J536-2\",,\"纵向输纸纸道的输纸传感器3 PS26\",,,,,,,\"VP3PD\"
,15,,\"5V\",,,\"J531BM-4\",,,\"J531BF-6\",,,\"J536-1\",,\"纵向输纸纸道的输纸传感器3 PS26\",,,,,,,\"5V\"
,16,,\" 24\",,,\"J531BM-3\",,,\"J531BF-7\",,,\"J537M-2\",,\"J537F-2\",,\"前置纸盒3(550张)进纸电磁铁SL3, 24V\"
,17,,\"C3PUSD/\",,,\"J531BM-2\",,,\"J531BF-8\",,,\"J537M-1\",,\"J537F-1\",,\"前置纸盒3(550张)进纸电磁铁SL3,驱动/\"
,,,,,\"空\",\"J531BM-1\",,,\"J531BF-9\"
,\"J110B\",,,,\"接前置纸盒4(550张)\"
,1,,\"0V\",,,\"J541AM-9\",,,\"J541AF-1\",,,\"J542-3\",,\"前置纸盒4(550张)升纸传感器PS18\",,,,,,,\"0V\"
,2,,\"C4LTP\",,,\"J541AM-8\",,,\"J541AF-2\",,,\"J542-2\",,\"前置纸盒4(550张)升纸传感器PS18\",,,,,,,\"C4LTP\"
,3,,\" 5V\",,,\"J541AM-7\",,,\"J541AF-3\",,,\"J542-1\",,\"前置纸盒4(550张)升纸传感器PS18\",,,,,,,\" 5V\"
,4,,\"0V\",,,\"J541AM-6\",,,\"J541AF-4\",,,\"J543-3\",,\"前置纸盒4(550张)纸检测传感器PS14\",,,,,,,\"0V\"
,5,,\"C3PD\",,,\"J541AM-5\",,,\"J541AF-5\",,,\"J543-2\",,\"前置纸盒4(550张)纸检测传感器PS14\",,,,,,,\"C4PD\"
,6,,\" 5V\",,,\"J541AM-4\",,,\"J541AF-6\",,,\"J543-1\",,\"前置纸盒4(550张)纸检测传感器PS14\",,,,,,,\" 5V\"
,7,,\"GND\",,,\"J541AM-3\",,,\"J541AF-7\",,,\"J544-3\",,\"前置纸盒4(550张)重新进纸传感器PS22\"
,8,,\"C4RTD\",,,\"J541AM-2\",,,\"J541AF-8\",,,\"J544-2\",,\"前置纸盒4(550张)重新进纸传感器PS22\"
,9,,\"5V\",,,\"J541AM-1\",,,\"J541AF-9\",,,\"J544-1\",,\"前置纸盒4(550张)重新进纸传感器PS22\"
,10,,\"0V\",,,\"J541BM-9\",,,\"J541BF-1\",,,\"J545-3\",,\"前置纸盒4(550张)关闭传感器PS16\",,,,,,,\"0V\"
,11,,\"C4OP\",,,\"J541BM-8\",,,\"J541BF-2\",,,\"J545-2\",,\"前置纸盒4(550张)关闭传感器PS16\",,,,,,,\"C4OP\"
,12,,\"5V\",,,\"J541BM-7\",,,\"J541BF-3\",,,\"J545-1\",,\"前置纸盒4(550张)关闭传感器PS16\",,,,,,,\"5V\"
,13,,\"GND\",,,\"J541BM-6\",,,\"J541BF-4\",,,\"J546-3\",,\"纵向输纸纸道的输纸传感器4 PS27\"
,14,,\"VP4PD\",,,\"J541BM-5\",,,\"J541BF-5\",,,\"J546-2\",,\"纵向输纸纸道的输纸传感器4 PS27\"
,15,,\"5V\",,,\"J541BM-4\",,,\"J541BF-6\",,,\"J546-1\",,\"纵向输纸纸道的输纸传感器4 PS27\"
,16,,\" 24\",,,\"J541BM-3\",,,\"J541BF-7\",,,\"J547M-2\",,\"J547F-1\",,\"前置纸盒4(550张)进纸电磁铁SL4, 24V\"
,17,,\"C4PUSD/\",,,\"J541BM-2\",,,\"J541BF-8\",,,\"J547M-1\",,\"J547F-2\",,\"前置纸盒4(550张)进纸电磁铁SL4,驱动/\"
,,,,,\"空\",\"J541BM-1\",,,\"J541BF-9\"
,,,,,,,,,,,,\"3500张(G1)右侧纸仓插座\"
,,,,,,,,,,,,,,,\"J702C-1\",,,,\"接地\"
,,,,,,,,,,,,,,,\"J702C-2\",,\"J325F-2\",,\"J1401M-5\",,\"J1401F-5\",,\"←J4006-1(DC电源板 24V)\"
,,,,,,,,,,,,,,,\"J702C-3\",,\"J325F-1\",,\"J1401M-6\",,\"J1401F-6\",,\"←J4006-2(DC电源板0V)\"
,\"J111-A\",,,,\"接3500张(G1)右侧纸仓\",,,,,,,,,,\"J702C-4\"
,\"1\",,\"S-CLK\",,,\"→\",\"J719M-7\",,\"J719F-1\",,\"→\",\"J702B-7\",,\"→\",\"J702A-7\",,\"→\"
,\"2\",,\"MOTOR-CLK\",,,\"→\",\"J719M-6\",,\"J719F-2\",,\"→\",\"J702B-6\",,\"→\",\"J702A-6\",,\"→\"
,\"3\",,\"TX-END\",,,\"→\",\"J719M-5\",,\"J719F-3\",,\"→\",\"J702B-5\",,\"→\",\"J702A-5\",,\"→\",\"接3500张(G1)右侧纸仓\"
,\"4\",,\"DOUT\",,,\"→\",\"J719M-4\",,\"J719F-4\",,\"→\",\"J702B-4\",,\"→\",\"J702A-4\",,\"→\"
,\"5\",,\"RX-LOAD\",,,\"→\",\"J719M-3\",,\"J719F-5\",,\"→\",\"J702B-3\",,\"→\",\"J702A-3\",,\"→\"
,\"6\",,\"S-DIN\",,,\"←\",\"J719M-2\",,\"J719F-6\",,\"←\",\"J702B-2\",,\"←\",\"J702A-2\",,\"←\"
,\"7\",,\"EN/\",,,\"→\",\"J719M-1\",,\"J719F-7\",,\"→\",\"J702B-1\",,\"→\",\"J702A-1\",,\"→\"
,\"8\",,\"FM3CLK\",,,,\"J718M-3\",,\"J718F-1\",,\"J8505-1\",,,\"排气冷却风扇FM3CLK同步信号\"
,\"9\",,\"GND\",,,,\"J718M-2\",,\"J718F-2\",,\"J8505-2\",,,\"排气冷却风扇(FM3)GND\"
,\"10\",,\"FM3ON\",,,,\"J718M-1\",,\"J718F-3\",,\"J8505-3\",,,\"排气冷却风扇(FM3)驱动信号\"
,\"J111-B\",,,,\"接前置纸盒3(550张)宽度/长度检测\"
,\"1\",,\"GND\",,,,,,,\"J5500-3\",,\"前置纸盒3(550张)宽度检测电位器SVR4\"
,\"2\",,\"C3PWD\",,,,,,,\"J5500-2\",,\"前置纸盒3(550张)宽度检测电位器SVR4\"
,\"3\",,\" 5V\",,,,,,,\"J5500-1\",,\"前置纸盒3(550张)宽度检测电位器SVR4\"
,\"4\",,\"C3PL1\",,,,\"J5770F-4\",,,\"J5770M-1\",,\"前置纸盒3(550张)长度检测VS2的S34\"
,\"5\",,\"GND\",,,,\"J5770F-3\",,,\"J5770M-2\",,\"前置纸盒3(550张)长度检测VS2的S33\"
,\"6\",,\"C3PL0\",,,,\"J5770F-2\",,,\"J5770M-3\",,\"前置纸盒3(550张)长度检测VS2的S32\"
,\"7\",,\" 5V\",,,,\"J5770F-1\",,,\"J5770M-4\",,\"前置纸盒3(550张)长度检测VS2的S31\"
,\"8\",,\"NC未用\"
,\"9\",,\"NC未用\"
,\"10\",,\"NC未用\"
,\"J112A\",,,,,\"右前置纸仓(1500张)纸检测\"
,1,,\"0V\",,,\"J511AM-9\",,,\"J511AF-1\",,\"J521-3\",,\"右前置纸仓(1500张)升纸传感器PS6\",,,,,,,,\"0V\"
,2,,\"RDLTP\",,,\"J511AM-8\",,,\"J511AF-2\",,\"J521-2\",,\"右前置纸仓(1500张)升纸传感器PS6\",,,,,,,,\"RDLTP\"
,3,,\" 5V\",,,\"J511AM-7\",,,\"J511AF-3\",,\"J521-1\",,\"右前置纸仓(1500张)升纸传感器PS6\",,,,,,,,\" 5V\"
,4,,\"0V\",,,\"J511AM-6\",,,\"J511AF-4\",,\"J513-3\",,\"右前置纸仓(1500张)纸检测传感器PS7\",,,,,,,,\"0V\"
,5,,\"RDPD\",,,\"J511AM-5\",,,\"J511AF-5\",,\"J513-2\",,\"右前置纸仓(1500张)纸检测传感器PS7\",,,,,,,,\"RDPD\"
,6,,\" 5V\",,,\"J511AM-4\",,,\"J511AF-6\",,\"J513-1\",,\"右前置纸仓(1500张)纸检测传感器PS7\",,,,,,,,\" 5V\"
,7,,\"GND\",,,\"J511AM-3\",,,\"J511AF-7\",,\"J515-3\",,\"右前置纸仓(1500张)重新进纸传感器PS19\",,,,,,,,\"GND\"
,8,,\"RDRT\",,,\"J511AM-2\",,,\"J511AF-8\",,\"J515-2\",,\"右前置纸仓(1500张)重新进纸传感器PS19\",,,,,,,,\"RDRT\"
,9,,\"5V\",,,\"J511AM-1\",,,\"J511AF-9\",,\"J515-1\",,\"右前置纸仓(1500张)重新进纸传感器PS19\",,,,,,,,\"5V\"
,\"J112B\",,,,,\"右前置纸仓(1500张)纸检测\"
,1,,\"0V\",,\"→\",\"J511BM-9\",,,\"J511BF-1\",,\"J516-3\",,\"右前置纸仓(1500张)关闭传感器PS5\"
,2,,\"RDEOP\",,\"←\",\"J511BM-8\",,,\"J511BF-2\",,\"J516-2\",,\"右前置纸仓(1500张)关闭传感器PS5\"
,3,,\" 5V\",,\"→\",\"J511BM-7\",,,\"J511BF-3\",,\"J516-1\",,\"右前置纸仓(1500张)关闭传感器PS5\"
,4,,\"0V\",,\"→\",\"J511BM-6\",,,\"J511BF-4\",,\"J517-3\",,\"右前置纸仓(1500张)进纸传感器PS32\"
,5,,\"RDPFS\",,\"←\",\"J511BM-5\",,,\"J511BF-5\",,\"J517-2\",,\"右前置纸仓(1500张)进纸传感器PS32\"
,6,,\" 5V\",,\"→\",\"J511BM-4\",,,\"J511BF-6\",,\"J517-1\",,\"右前置纸仓(1500张)进纸传感器PS32\"
,7,,\"0V\",,\"→\",\"J511BM-3\",,,\"J511BF-7\",,\"J518-3\",,\"右前置纸仓(1500张)纸上限传感器PS8\"
,8,,\"RDEL\",,\"←\",\"J511BM-2\",,,\"J511BF-8\",,\"J518-2\",,\"右前置纸仓(1500张)纸上限传感器PS8\"
,9,,\" 5V\",,\"→\",\"J511BM-1\",,,\"J511BF-9\",,\"J518-1\",,\"右前置纸仓(1500张)纸上限传感器PS8\"
,\"J113A\"
,1,\"GND\",,,\"→\",\"J801AM-15\",,,\"J801AF-1\",,,\"J802M-3\",,\"J802F-1\",,\"J1521-3\",,\"纵向输纸纸道的输纸传感器2 PS25\"
,2,\"VP2PD\",,,\"←\",\"J801AM-14\",,,\"J801AF-2\",,,\"J802M-2\",,\"J802F-2\",,\"J1521-2\",,\"纵向输纸纸道的输纸传感器2 PS25\"
,3,\"5V\",,,\"→\",\"J801AM-13\",,,\"J801AF-3\",,,\"J802M-1\",,\"J802F-3\",,\"J1521-1\",,\"纵向输纸纸道的输纸传感器2 PS25\"
,4,\"GND\",,,\"←\",\"J801AM-12\",,,\"J801AF-4\",,,\"J803M-1\",,\"J803F-1\",,\"J1523-3\",,\"纵向输纸纸道的输纸传感器1 PS24\"
,5,\"VP1PD\",,,\"←\",\"J801AM-11\",,,\"J801AF-5\",,,\"J803M-2\",,\"J803F-2\",,\"J1523-2\",,\"纵向输纸纸道的输纸传感器1 PS24\"
,6,\"5V\",,,\"→\",\"J801AM-10\",,,\"J801AF-6\",,,\"J803M-3\",,\"J803F-3\",,\"J1523-1\",,\"纵向输纸纸道的输纸传感器1 PS24\"
,7,\"GND\",,,,\"J801AM-9\",,,\"J801AF-7\",,,\"J8492-5\",,\"环境传感器HUM1\"
,8,\"TH\",,,,\"J801AM-8\",,,\"J801AF-8\",,,\"J8492-4\",,\"环境传感器HUM1\"
,9,\"GND\",,,,\"J801AM-7\",,,\"J801AF-9\",,,\"J8492-3\",,\"环境传感器HUM1\"
,10,\"HUM OUT\",,,,\"J801AM-6\",,,\"J801AF-10\",,,\"J8492-2\",,\"环境传感器HUM1\"
,11,\" 5V\",,,,\"J801AM-5\",,,\"J801AF-11\",,,\"J8492-1\",,\"环境传感器HUM1\"
,12,\"NC\",,,,\"J801AM-4\",,,\"J801AF-12\",,,\"J809M-4\",,\"J809F-1\"
,13,\"GND\",,,,\"J801AM-3\",,,\"J801AF-13\",,,\"J809M-3\",,\"J809F-2\",,\"J8508-3\",,\"右下盖关闭传感器PS2\",,,,,\"GND\"
,14,\"LODOP\",,,,\"J801AM-2\",,,\"J801AF-14\",,,\"J809M-2\",,\"J809F-3\",,\"J8508-2\",,\"右下盖关闭传感器PS2\",,,,,\"LODOP\"
,15,\"5V\",,,,\"J801AM-1\",,,\"J801AF-15\",,,\"J809M-1\",,\"J809F-4\",,\"J8508-1\",,\"右下盖关闭传感器PS2\",,,,,\"5V\"
,\"J113B\",,,,,,,,,,,,,\"注:手送纸时由对位传感器PS29检测到复印纸前沿开始激光读出\"
,1,\"GND\",,,\"→\",\"J801BM-15\",,,\"J801BF-1\",,,\"J807M-3\",,\"J807F-1\",,\"J1519-1\",,\"对位辊前的激光读出的起始位置传感器PS28\"
,2,\"LWRPD\",,,\"←\",\"J801BM-14\",,,\"J801BF-2\",,,\"J807M-2\",,\"J807F-2\",,\"J1519-2\",,\"对位辊前的激光读出的起始位置传感器PS28\",,,,,,,,\"\\\"1\\\"有纸\"
,3,\"5V\",,,\"→\",\"J801BM-13\",,,\"J801BF-3\",,,\"J807M-1\",,\"J807F-3\",,\"J1519-3\",,\"对位辊前的激光读出的起始位置传感器PS28\"
,4,\"GND\",,,,\"J801BM-12\",,,\"J801BF-4\",,,\"J9003M-3\",,\"J9003F-1\",,\"J9004M-3\",,\"J9004F-1\",,\"J806-3\",,\"前置纸盒3(550张)纸残余量检测电位器SVR2\"
,5,\"C3PLV\",,,,\"J801BM-11\",,,\"J801BF-5\",,,\"J9003M-2\",,\"J9003F-2\",,\"J9004M-2\",,\"J9004F-2\",,\"J806-2\",,\"前置纸盒3(550张)纸残余量检测电位器SVR2\"
,6,\"5V\",,,,\"J801BM-10\",,,\"J801BF-6\",,,\"J9003M-1\",,\"J9003F-3\",,\"J9004M-1\",,\"J9004F-3\",,\"J806-1\",,\"前置纸盒3(550张)纸残余量检测电位器SVR2\"
,7,\"GND\",,,,\"J801BM-9\",,,\"J801BF-7\",,,\"J9008M-3\",,\"J9008F-1\",,\"J9006M-3\",,\"J9006F-1\",,\"J810-3\",,\"前置纸盒4(550张)纸残余量检测电位器SVR3\"
,8,\"C4PLV\",,,,\"J801BM-8\",,,\"J801BF-8\",,,\"J9008M-2\",,\"J9008F-2\",,\"J9006M-2\",,\"J9006F-2\",,\"J810-2\",,\"前置纸盒4(550张)纸残余量检测电位器SVR3\"
,9,\"5V\",,,,\"J801BM-7\",,,\"J801BF-9\",,,\"J9008M-1\",,\"J9008F-3\",,\"J9006M-1\",,\"J9006F-3\",,\"J810-1\",,\"前置纸盒4(550张)纸残余量检测电位器SVR3\"
,10,\"0V\",,,,\"J801BM-6\",,,\"J801BF-10\",,,\"J804M-2\",,\"J804F-1\",,\"前置纸盒3(550张)升纸电机M20\"
,11,\"C3LMD\",,,,\"J801BM-5\",,,\"J801BF-11\",,,\"J804M-1\",,\"J804F-2\",,\"前置纸盒3(550张)升纸电机M20\"
,12,\"0V\",,,,\"J801BM-4\",,,\"J801BF-12\",,,\"J805M-2\",,\"J805F-1\",,\"前置纸盒4(550张)升纸电机M21\"
,13,\"C4LMD\",,,,\"J801BM-3\",,,\"J801BF-13\",,,\"J805M-1\",,\"J805F-2\",,\"前置纸盒4(550张)升纸电机M21\"
,14,\"NC,未用\",,,,\"J801BM-2\",,,\"J801BF-14\"
,15,\"NC,未用\",,,,\"J801BM-1\",,,\"J801BF-15\"
,\"J122A\",,,\"接主控制板(PCB24)的J1015-A\"
,\"J122B\",,,\"接主控制板(PCB24)的J1015-B\"
,\"J114\",,,,,,,,,,\"移动纸盘(B1)板\"
,1,\"5V\",,\"→\",,\"J201M-1\",,\"J201F-1\",,\"→\",\"J101-1\",,\"5V\"
,2,\"GND\",,\"→\",,\"J201M-2\",,\"J201F-2\",,\"→\",\"J101-2\",,\"GND\"
,3,\"24V\",,\"→\",,\"J201M-3\",,\"J201F-3\",,\"→\",\"J101-3\",,\"24V\"
,4,\"GND\",,\"→\",,\"J201M-4\",,\"J201F-4\",,\"→\",\"J101-4\",,\"GND\"
,5
,\"J123\",,,\"接移动纸盘(B1)板\"
,\"1\",\"GND\",,,,\"J202F-10\",,\"J202M-1\",,\"→\",\"J102-10\"
,\"2\",\"FULLON\",,,,\"J202F-9\",,\"J202M-2\",,\"→\",\"J102-9\"
,\"3\",\"SCW\",,,,\"J202F-8\",,\"J202M-3\",,\"→\",\"J102-8\",,\"移动电机正转\"
,\"4\",\"SCCW\",,,,\"J202F-7\",,\"J202M-4\",,\"→\",\"J102-7\",,\"移动电机反转\"
,\"5\",\"SPFULL\",,,,\"J202F-6\",,\"J202M-5\",,\"←\",\"J102-6\",,\"纸盘满载纸信号\"
,\"6\",\"SPEXIST/\",,,,\"J202F-5\",,\"J202M-6\",,\"←\",\"J102-5\",,\"纸盘纸传感器PS103\"
,\"7\",\"STHPL\",,,,\"J202F-4\",,\"J202M-7\",,\"←\",\"J102-4\",,\"原位传感器PS10(内)\"
,\"8\",\"STHPR\",,,,\"J202F-3\",,\"J202M-8\",,\"←\",\"J102-3\",,\"原位传感器PS101(外)\"
,\"9\",\"STCNCT/\",,,,\"J202F-2\",,\"J202M-9\",,\"←\",\"J102-2\",,\"移动纸盘接入检测信号\"
,\"10\",\"GND\",,,,\"J202F-1\",,\"J202M-10\",,\"→\",\"J102-1\",,\"GND\"
,\"J115A\",,,,,\"左前置纸仓(1500张)纸检测\"
,1,\"0V\",,,\"J561M-15\",,,\"J561F-1\",,,\"J546-3\",,\"左前置纸仓(1500张)纸上限位置传感器PS12\",,,,,,,,,\"0V\"
,2,\"LDEL\",,,\"J561M-14\",,,\"J561F-2\",,,\"J546-2\",,\"左前置纸仓(1500张)纸上限位置传感器PS12\",,,,,,,,,\"LDEL\"
,3,\"5V\",,,\"J561M-13\",,,\"J561F-3\",,,\"J546-1\",,\"左前置纸仓(1500张)纸上限位置传感器PS12\",,,,,,,,,\"5V\"
,4,\"0V\",,,\"J561M-12\",,,\"J561F-4\",,,\"J565-3\",,\"左前置纸仓(1500张)升纸传感器PS12\",,,,,,,,,\"0V\"
,5,\"LDLTP\",,,\"J561M-11\",,,\"J561F-5\",,,\"J565-2\",,\"左前置纸仓(1500张)升纸传感器PS12\",,,,,,,,,\"LDLTP\"
,6,\"5V\",,,\"J561M-10\",,,\"J561F-6\",,,\"J565-1\",,\"左前置纸仓(1500张)升纸传感器PS12\",,,,,,,,,\"5V\"
,7,\"0V\",,,\"J561M-9\",,,\"J561F-7\",,,\"J567-3\",,\"左前置纸仓(1500张)升纸传感器PS11\",,,,,,,,,\"0V\"
,8,\"LDPD\",,,\"J561M-8\",,,\"J561F-8\",,,\"J567-2\",,\"左前置纸仓(1500张)升纸传感器PS11\",,,,,,,,,\"LDPD\"
,9,\"5V\",,,\"J561M-7\",,,\"J561F-9\",,,\"J567-1\",,\"左前置纸仓(1500张)升纸传感器PS11\",,,,,,,,,\"5V\"
,10,\"0V\",,,\"J561M-6\",,,\"J561F-10\",,,\"J568-3\",,\"左前置纸仓(1500张)重新进纸传感器PS20\",,,,,,,,,\"0V\"
,11,\"LDRT\",,,\"J561M-5\",,,\"J561F-11\",,,\"J568-2\",,\"左前置纸仓(1500张)重新进纸传感器PS20\",,,,,,,,,\"LDRT\"
,12,\"5V\",,,\"J561M-4\",,,\"J561F-12\",,,\"J568-1\",,\"左前置纸仓(1500张)重新进纸传感器PS20\",,,,,,,,,\"5V\"
,13,\"0V\",,,\"J561M-3\",,,\"J561F-13\",,,\"J569-3\",,\"左前置纸仓(1500张)关闭传感器PS9\",,,,,,,,,\"0V\"
,14,\"LDEOP\",,,\"J561M-2\",,,\"J561F-14\",,,\"J569-2\",,\"左前置纸仓(1500张)关闭传感器PS9\",,,,,,,,,\"LDEOP\"
,15,\"5V\",,,\"J561M-1\",,,\"J561F-15\",,,\"J569-1\",,\"左前置纸仓(1500张)关闭传感器PS9\",,,,,,,,,\"5V\"
,\"J115B\",,,,,\"左;右前置纸仓(1500张)纸残余量检测\"
,1,\"0V\",,,\"J5700F-6\",,,\"J5700M-1\",,,\"J571-3\",,\"右前置纸仓(1500张)纸残余量检测传感器PS47\",,,,,,,,,\"0V\",,\"(上)\"
,2,\"RDPD1\",,,\"J5700F-5\",,,\"J5700M-2\",,,\"J571-2\",,\"右前置纸仓(1500张)纸残余量检测传感器PS47\",,,,,,,,,\"RDPD1\",,\"(上)\"
,3,\"5V\",,,\"J5700F-4\",,,\"J5700M-3\",,,\"J571-1\",,\"右前置纸仓(1500张)纸残余量检测传感器PS47\",,,,,,,,,\"5V\",,\"(上)\"
,4,\"0V\",,,\"J5700F-3\",,,\"J5700M-4\",,,\"J572-3\",,\"右前置纸仓(1500张)纸残余量检测传感器PS48\",,,,,,,,,\"0V\",,\"(下)\"
,5,\"RDPD2\",,,\"J5700F-2\",,,\"J5700M-5\",,,\"J572-2\",,\"右前置纸仓(1500张)纸残余量检测传感器PS48\",,,,,,,,,\"RDPD2\",,\"(下)\"
,6,\"5V\",,,\"J5700F-1\",,,\"J5700M-6\",,,\"J572-1\",,\"右前置纸仓(1500张)纸残余量检测传感器PS48\",,,,,,,,,\"5V\",,\"(下)\"
,7,\"0V\",,,\"J5701F-1\",,,\"J5701M-1\",,,\"J573-3\",,\"左前置纸仓(1500张)纸残余量检测传感器PS49\",,,,,,,,,\"0V\",,\"(上)\"
,8,\"LDPD1\",,,\"J5701F-2\",,,\"J5701M-2\",,,\"J573-2\",,\"左前置纸仓(1500张)纸残余量检测传感器PS49\",,,,,,,,,\"LDPD1\",,\"(上)\"
,9,\"5V\",,,\"J5701F-3\",,,\"J5701M-3\",,,\"J573-1\",,\"左前置纸仓(1500张)纸残余量检测传感器PS49\",,,,,,,,,\"5V\",,\"(上)\"
,10,\"0V\",,,\"J5701F-4\",,,\"J5701M-4\",,,\"J574-3\",,\"左前置纸仓(1500张)纸残余量检测传感器PS50\",,,,,,,,,\"0V\",,\"(下)\"
,11,\"LDPD2\",,,\"J5701F-5\",,,\"J5701M-5\",,,\"J574-2\",,\"左前置纸仓(1500张)纸残余量检测传感器PS50\",,,,,,,,,\"LDPD2\",,\"(下)\"
,12,\"5V\",,,\"J5701F-6\",,,\"J5701M-6\",,,\"J574-1\",,\"左前置纸仓(1500张)纸残余量检测传感器PS50\",,,,,,,,,\"5V\",,\"(下)\"
,13,\" 24V\",,,,,,\"J717M-2\",,,\"J717F-1\",,\"左前置纸仓(1500张)拉拔离合器CL4, 24V\",,,,,,,,,\" 24V\"
,14,\"LDCLD/\",,,,,,\"J717M-1\",,,\"J717F-2\",,\"左前置纸仓(1500张)拉拔离合器CL4,驱动/,LDCLD/\",,,,,,,,,\"LDCLD/\"
,15,\"NC\"
,\"J116\",,,,,,,,,,,\"激光扫描电机M15驱动板\"
,1,\"LMSPSEL \",,,,\"J201M-5\",,\"J201F-1\",,\"J2511-1\",,\"\\\"0\\\"全速;\\\"1\\\"半速\"
,2,\"LMRDY/\",,,,\"J201M-4\",,\"J201F-2\",,\"J2511-2\",,\"电机准备就绪\"
,3,\"LMON\",,,,\"J201M-3\",,\"J201F-3\",,\"J2511-3\",,\"激光扫描电0N\"
,4,\" 24V\",,,,\"J201M-2\",,\"J201F-4\",,\"J2511-4\",,\" 24V\"
,5,\"GND\",,,,\"J201M-1\",,\"J201F-5\",,\"J2511-5\",,\"GND\"
,\"J120\",,,,,,,,,,\"激光原位传感器板(PCB14)\"
,1,\"5V\",,,,\"J401M-4\",,\"J401F-1\",,\"J2701-4\",,\"5V\"
,2,\"BDIN\",,,,\"J401M-3\",,\"J401F-2\",,\"J2701-3\",,\"BDIN\",,\"激光原位信号\"
,3,\"GND\",,,,\"J401M-2\",,\"J401F-3\",,\"J2701-2\",,\"GND\"
,4,,,,,\"J401M-1\",,\"J401F-4\",,\"J2701-1\"
,\"J117\"
,1,,,,,,,\"激光驱动电路板PCB11\"
,2,\"LD( )\",,,,,,\"J2502-3\",,\"激光驱动信号\",,,\" \",,,\" \"
,3,\"LD(-)\",,,,,,\"J2502-2\",,\"激光驱动信号\"
,4,\"GND\",,,,,,\"J2502-1\"
,\"J121\",,\"接激光驱动电路板\"
,1,\"THEM-\",,,,,,\"J2501-20\"
,2,\"THEM \",,,,,,\"J2501-19\"
,3,\"GND\",,,,,,\"J2501-18\"
,4,\"5V\",,,,,,\"J2501-17\"
,5,\"HEATER-ON\",,,,,,\"J2501-16\"
,6,\"24V\",,,,,,\"J2501-15\"
,7,\"GND\",,,,,,\"J2501-14\"
,8,\"LZ-LDPSEL1\",,,,,,\"J2501-13\"
,9,\"LD-DT\",,,\"→\",,,\"J2501-12\",,\"激光亮度的基准信号\"
,10,\"GND\",,,,,,\"J2501-11\"
,11,\"LD-EN\",,,\"→\",,,\"J2501-10\",,\"激光允许信号\"
,12,\"SAMLE1\",,,,,,\"J2501-9\"
,13,\"GND\",,,,,,\"J2501-8\"
,14,\"LSH\",,,\"→\",,,\"J2501-7\"
,15,\"NC\",,,,,,\"J2501-6\"
,16,\"NC\",,,,,,\"J2501-5\"
,17,\"NC\",,,,,,\"J2501-4\"
,18,\"3.3V\",,,,,,\"J2501-3\"
,19,\"ND\",,,,,,\"J2501-2\"
,20,\"L-RDY\",,,\"←\",,,\"J2501-1\"
,\"J124\",,,\"接硬盘冷却风扇FM7;突入电流防止电路板\"
,\"1\",\"FM7-DETECT\",,,,\"J1451M-5\",,\"J1451F-1\"
,\"2\",\"GND\",,,,\"J1451M-4\",,\"J1451F-2\"
,\"3\",\"FM7ON\",,,,\"J1451M-3\",,\"J1451F-3\",,\"J1542M-3\",,\"J1542F-1\",,\"硬盘冷却风扇(FM7)ON信号\"
,\"4\",\"FM7CLK\",,,,\"J1451M-2\",,\"J1451F-4\",,\"J1542M-2\",,\"J1542F-2\",,\"硬盘冷却风扇FM7CLK同步信号\"
,\"5\",\"0V\",,,,\"J1451M-1\",,\"J1451F-5\",,\"J1542M-1\",,\"J1542F-3\",,\"硬盘冷却风扇FM7,GND\"
,\"6\",\"GND\",,,,\"J1453M-3\",,\"J1453F-3\",,\"J1413-1\",,,,\"突入电流防止电路板\"
,\"7\",,,,,\"J1453M-2\",,\"J1453F-2\",,\"J1413-2\",,,,\"突入电流防止电路板\"
,\"8\",,,,,\"J1453M-1\",,\"J1453F-1\",,\"J1413-3\",,,,\"突入电流防止电路板\"
,\"J125\",,,\"接前置纸盒4(550张)宽度/长度检测电位器\",,,,,,,,,,,,,,\"仅100V机使用\"
,\"1\",\"EX/DOM/ DETECT\"
,\"2\"
,\"3\",\"0V\",,,,\"J550-3\",,,,,,\"前置纸盒4(550张)宽度检测电位器SVR5\",,,,,,,,\"仅100V机使用\"
,\"4\",\"C4PWD\",,,,\"J550-2\",,,,,,\"前置纸盒4(550张)宽度检测电位器SVR5\",,,,,,,,\"仅100V机使用\"
,\"5\",\"5V\",,,,\"J550-1\",,,,,,\"前置纸盒4(550张)宽度检测电位器SVR5\",,,,,,,,\"仅100V机使用\"
,\"6\",\"C4PL1\",,,,\"J577F-4\",,\"J577M-1\",,,,\"前置纸盒4(550张)长度检测电位器SV1\",,,,,,,,\"仅100V机使用\"
,\"7\",\"0V\",,,,\"J577F-3\",,\"J577M-2\",,,,\"前置纸盒4(550张)长度检测电位器SV1\",,,,,,,,\"仅100V机使用\"
,\"8\",\"C4PL0\",,,,\"J577F-2\",,\"J577M-3\",,,,\"前置纸盒4(550张)长度检测电位器SV1\",,,,,,,,\"仅100V机使用\"
,\"9\",\"5V\",,,,\"J577F-1\",,\"J577M-4\",,,,\"前置纸盒4(550张)长度检测电位器SV1\",,,,,,,,\"仅100V机使用\"
,,\"PS1\",\"前置纸盒1,有纸/无纸传感器PS1\"
,,\"PS2\",\"前置纸盒2,有纸/无纸传感器PS2\"
,,\"PS3\",\"前置纸盒1纸剩余量传感器-1\"
,,\"PS4\",\"前置纸盒1纸剩余量传感器-2\",,,,,,,,,\"选购件3500张右侧纸仓(L1)\"
,,\"PS5\",\"前置纸盒2纸剩余量传感器-1\"
,,\"PS6\",\"前置纸盒2纸剩余量传感器-2\",,,,,,,,,\"选购件纸盒工作台W1的纵向输纸道的输纸传感器Q1603\"
,,\"PS7\",\"前置纸盒1再搓纸传感器PS7\",,,,,,,,,\"选购件纸盒工作台W1的前置纸盒3再进纸传感器PS2C\"
,,\"PS8\",\"前置纸盒2再搓纸传感器PS8\",,,,,,,,,\"选购件纸盒工作台W1的前置纸盒4再进纸传感器PS3C\"
,,\"PS9\",\"预对位辊传感器PS9,(纵向输纸)\",,,,,,,,,\"选购件3500张右侧纸仓(L1)搓纸传感器PS1D(P-OUT-SENS)\"
,,\"PS10\",\"对位辊传感器PS10,(水平输纸)\",,,,,,,,,\"选购件3500张右侧纸仓(L1)输纸传感器PS6D(FEED-SENS)\"
,,\"PS11\",\"双面纸横向对位传感器PS11(Y-REG-PD)开始激光图像曝光(主扫描图像对位)\"
,,\"PS12\",\"图像前沿传感器PS12(纸前沿到达转印前输纸棍前端的图像前沿传感器PS12,开始图像激光向鼓曝光),复印图像激光副扫描对位\"
,,\"PS13\",\"定影出口纸输送辊传感器PS13\"
,,\"PS14\"
,,\"PS15\",\"No.1接纸盘(机内基本接纸盘)排纸检测传感器PS15\"
,,\"PS16\",\"No.1接纸盘(机内基本接纸盘)排纸溢出检测传感器PS16\"
,,\"PS17\",\"纸张进入双面纸盘传感器PS17\"
,,\"PS18\",\"纸张从双面纸盘排出传感器PS18\"
,,\"PS19B\",,\"No.2接纸盘(内置2路纸托盘的上层)排纸检测传感器PS19B\"
,,\"PS20B\",,\"No.2接纸盘(内置2路纸托盘的上层)排纸溢出检测传感器PS20B\"
,,\"PS21B\",,\"No.3接纸盘(外置接纸托盘)排纸检测传感器PS21B\"
,,\"PS22\",,\"手进纸盘,有纸/无纸传感器PS22\"
,,\"PS23\",,\"右边门打开/关闭检测传感器\"
,,\"PS24B\",,\"内置2路纸托盘-A1,排纸部打开/关关检测传感器PS24B\"
,,\"PS25\"
,,\"PS26\"
,,\"PS27\"
,,\"PS28\",,\"手送纸传感器PS28\"
,,\"Q1604\",,\"前置纸盒1纸用完传感器\"
,,\"Q1605\",,\"前置纸盒2纸用完传感器\"
,,\"M1\",,\"主电机,驱动:\",,,\"通过纸盘1,2搓纸轮下降电磁铁SL1驱动凸轮使纸盘1,2搓纸轮下降\"
,,,,,,,\"通过手进纸盘搓纸离合器CL2(MLT-CL)驱动手进纸盘搓纸轮\"
,,,,,,,\"通过手进纸盘搓纸导板放电磁铁SL5(MTL-SL)将手进纸盘搓纸导板靠上手进纸盘搓纸轮\"
,,,,,,,\"转印前输纸棍(水平输纸);OPC鼓;转印棍;\"
,,\"M2\",,\"M2电机顺时针旋转驱动纸盒1搓纸轮,M2电机逆时针旋转驱动纸盒搓纸轮,\"
,,\"M3\",,\"双面纸横向对位电机\"
,,\"M4\",,\"定影电机\"
,,\"M5\",,\"定影纸垂直向上排出电机;双面复印时,M5电机反转将第1面复印件反转送入双面输纸部\"
,,\"M6\",,\"驱动横向对位传感器步进电机M3\"
,,\"M7B\",,\"内置2路纸托盘-A1,向No.2盘排纸的进入轮驱动步进电机\"
,,\"M7Z\",,\"中继排纸组件,纸排出步进电机\"
,,\"M8B\",,\"内置2路纸托盘-A1纸排出步进电机\"
,,,,\"M8B电机正转驱动No.2接纸盘排纸轮,No.3接纸盘排纸轮将纸排向No.2接纸盘\"
,,,,\"M8B电机反转驱动No.2接纸盘排纸轮,No.3接纸盘排纸轮将纸排向No.3接纸盘\"
,,\"M9\",,\"对位辊电机\"
,,\"M10\",,\"驱动6个光反射面菱镜的激光扫描电机\"
,,\"CL1\",\"纵向输纸辊离合器CL1使M1驱动纵向输纸轮;预对位辊;纸盘1,2纸排出输送轮\"
,,\"CL2\",\"手进纸盘搓离合器MLT-CL\"
,,\"CL3\",\"显影器离合器\"
,,\"SL1\",\"纸盘1,2搓纸轮下降电磁铁SL1(使凸轮放,搓纸轮向下降)\"
,,\"SL2\"
,,\"SL3\"
,,\"SL4\",\"向No.2接纸盘排纸叉门挡板驱动电磁铁;SL4 OFF纸排入No.1接纸盘(机内基本接纸盘)\"
,,\"SL5\",\"手进纸盘搓纸导板放电磁铁MTL-SL\"
,,\"SL6\",\"一次充电辊清洁电磁铁\"
,,\"MF1\",\"显影器冷却风扇\"
,,\"MF2\",\"定影器冷却风扇\"
,,\"MF3\"
,,\"MF4\"
,,\"MF5\"
,,,\"选购件鞍式分页装订器-G1的主板接插件连接图\",,,,,,,,,,,,,,\"Saddle Finisher-G1\"
,,,,\"CN1\",\"接复印机\"
,,,,\"1\",\" 24V\",,\"←\"
,,,,\"2\"
,,,,\"3\",\"PGND\",,\"←\"
,,,,\"CN2\",\"接复印机\"
,,,,\"1\",\" 24V\",,\"←\"
,,,,\"2\",\"空\"
,,,,\"3\",\"SGND\",,\"←\"
,,,,\"4\",\"SGND\",,\"←\"
,,,,\"5\",\"TXD\",,\"←\"
,,,,\"6\",\"RXD\",,\"→\"
,,,,\"7\",\"SGND\",,\"←\"
,,,,\"CN3\"
,,,,\"1\",\"M4\",,,,\"CN62-5\",,\"CN63-1\",,\" 24V\"
,,,,\"2\",\"M4\",,,,\"CN62-4\",,\"CN63-2\",,\"图8/8,前拍纸板步进电机M4 A相信号FJOGMTR-A\"
,,,,\"3\",\"M4\",,,,\"CN62-3\",,\"CN63-3\",,\"图8/8,前拍纸板步进电机M4 A/相信号FJOGMTR-A/\"
,,,,\"4\",\"M4\",,,,\"CN62-2\",,\"CN63-4\",,\"图8/8,前拍纸板步进电机M4 B相信号FJOGMTR-B\"
,,,,\"5\",\"M4\",,,,\"CN62-1\",,\"CN63-5\",,\"图8/8,前拍纸板步进电机M4 B/相信号FJOGMTR-B/\"
,,,,\"6\",\"M5\",,,,\"CN64-5\",,\"CN65-1\",,\" 24V\"
,,,,\"7\",\"M5\",,,,\"CN64-4\",,\"CN65-2\",,\"图8/8,后拍纸板步进电机M5 A相信号RJOGMTR-A\"
,,,,\"8\",\"M5\",,,,\"CN64-3\",,\"CN65-3\",,\"图8/8,后拍纸板步进电机M5 A/相信号RJOGMTR-A/\"
,,,,\"9\",\"M5\",,,,\"CN64-2\",,\"CN65-4\",,\"图8/8,后拍纸板步进电机M5 B相信号RJOGMTR-B\"
,,,,\"10\",\"M5\",,,,\"CN64-1\",,\"CN65-5\",,\"图8/8,后拍纸板步进电机M5 B/相信号RJOGMTR-B/\"
,,,,\"CN4\"
,,,,\"1\",\" 5V\",,,,,,,,\"CN23-1\",,\" 5V\"
,,,,\"2\",\"GND\",,,,,,,,\"CN23-2\",,\"GND\"
,,,,\"3\",\"F-JOG-HP\",,,,,,,,\"CN23-3\",,\"PI4\",\"图5/8,拍纸板传感器(前)←CN4-2 FJOG-HP\"
,,,,\"4\",\" 5V\",,,,,,,,\"CN24-1\",,\" 5V\"
,,,,\"5\",\"GND\",,,,,,,,\"CN24-2\",,\"GND\"
,,,,\"6\",\"TOPCOV-S\",,,,,,,,\"CN24-3\",,\"P23\",\"图6/8,鞍式分页装订器-G1的上盖ON/OFF检测传感器信号,TOPCOV-S\"
,,,,\"7\",\" 5V\",,,,,,,,\"CN25-1\",,\" 5V\"
,,,,\"8\",\"GND\",,,,,,,,\"CN25-2\",,\"GND\"
,,,,\"9\",\"FDOOR-S\",,,,,,,,\"CN25-3\",,\"P22\",\"图6/8,鞍式分页装订器-G1的前盖ON/OFF检测传感器信号,FDOOR-S\"
,,,,\"CN5\"
,,,,\"1\",\" 5V\",,,,\"CN28-9\",,\"CN29-1\",,\"CN30-3\",,\" 5V\"
,,,,\"2\",\"GND\",,,,\"CN28-8\",,\"CN29-2\",,\"CN30-2\",,\"GND\"
,,,,\"3\",\"ADJ-TRAY-S\",,,,\"CN28-7\",,\"CN29-3\",,\"CN30-1\",,\"PI6\",\"图7/8,纸堆垛处理盘纸传感器信号ADJ-TRAY-S 1:有纸\"
,,,,\"4\",\" 5V\",,,,\"CN28-6\",,\"CN29-4\",,\"CN31-3\",,\" 5V\"
,,,,\"5\",\"GND\",,,,\"CN28-5\",,\"CN29-5\",,\"CN31-2\",,\"GND\"
,,,,\"6\",\"EJCT-BLT-HP\",,,,\"CN28-4\",,\"CN29-6\",,\"CN31-1\",,\"PI7\",\"图6/8,CN5-6,纸堆垛处理盘排纸皮带原位传感器EJCT-BLT-HP\"
,,,,\"7\",\" 5V\",,,,\"CN28-3\",,\"CN29-7\",,\"CN32-3\",,\" 5V\"
,,,,\"8\",\"GND\",,,,\"CN28-2\",,\"CN29-8\",,\"CN32-2\",,\"GND\"
,,,,\"9\",\"TRY-EMPS\",,,,\"CN28-1\",,\"CN29-9\",,\"CN32-1\",,\"PI8\",\"图6/8,CN5-9,纸堆垛处理排纸盘纸空传感器←CN5-9,TRAY-EMPS\"
,,,,\"10\",\" 5V\",,,,\"CN33-3\",,\"CN34-1\",,\"CN35-3\",,\" 5V\"
,,,,\"11\",\"GND\",,,,\"CN33-2\",,\"CN34-2\",,\"CN35-2\",,\"GND\"
,,,,\"12\",\"LVL-S\",,,,\"CN33-1\",,\"CN34-3\",,\"CN35-1\",,\"PI9\",\"图5/8,纸表面传感器←CN5-12 LVL-S\"
,,,,\"13\",\" 5V\",,,,,,,,\"CN36-3\"
,,,,\"14\",\"GND\",,,,,,,,\"CN36-2\"
,,,,\"15\",\"R-JOG-HP\",,,,,,,,\"CN36-1\",,\"PI5\",\"图5/8,拍纸板传感器(后)←CN5-15 R-JOG-HP\"
,,,,\"CN6\"
,,,,\"1\",\"SIFTMTR-1\",,,,\"CN70-2\",,,\"图7/8,Finisher-G1接纸托盘升降电机M6\"
,,,,\"2\",\"SIFTMTR-0\",,,,\"CN70-1\",,,\"图7/8,Finisher-G1接纸托盘升降电机M6\"
,,,,\"3\",\"BINDMTR-1\",,,,\"CN71-1\",,,\"图8/8,鞍式装订/对折纸电机M7逆时针旋转CW,STPLMTR-FWD(BINDMTR-1)\"
,,,,\"4\",\"BINDMTR-0\",,,,\"CN71-2\",,,\"图8/8,鞍式装订/对折纸电机M7逆时针旋转CCW,STPLMTR-REV(BINDMTR-0)\"
,,,,\"CN8\"
,,,,\"1\",\"装订安全开关MS3, STPLSAFE-SW\"
,,,,\"2\"
,,,,\"3\",\"前门开关MS1, FDOOR-SW\"
,,,,\"4\"
,,,,\"5\",\"与主机连接检测开关MS2, JOINT-SW\"
,,,,\"6\",\" 24VP\"
,,,,\"CN9\"
,,,,\"1\",\" 5V\",,,,,,,,\"CN51-1\",,\" 5V\"
,,,,\"2\",\"GND\",,,,,,,,\"CN51-2\",,\"GND\"
,,,,\"3\",\"PDL-HP\",,,,,,,,\"CN51-3\",,\"PI2\",\"图5/8,纸堆垛处理盘蹼轮原位传感器信号CN9-3 PDL-HP\"
,,,,\"4\",\"GND\",,,,,,,,\"CN52-3\",,\"GND\"
,,,,\"5\",\"BIND-EMPS\",,,,,,,,\"CN52-2\",,\"PI14\"
,,,,\"6\",\" 5V\",,,,,,,,\"CN52-1\",,\" 5V\"
,,,,\"7\",\" 5V\",,,,\"CN53-3\",,\"CN54-1\",,\"CN55-3\",,\" 5V\"
,,,,\"8\",\"GND\",,,,\"CN53-2\",,\"CN54-2\",,\"CN55-2\",,\"GND\"
,,,,\"9\",\"BDL-ROL-HP\",,,,\"CN53-1\",,\"CN54-3\",,\"CN55-1\",,\"PI3\",\"图5/8,纸堆垛处理盘排纸轮转换导向原位传感器信号CN9-9 BDL-ROL-HP\"
,,,,\"CN10\"
,,,,\"1\",\"M1\",,\"CN56-1\",,\"CN56-6\",,\" 24V\"
,,,,\"2\",\"M1\",,\"CN56-2\",,\"CN56-5\",,\" 24V\"
,,,,\"3\",\"M1\",,\"CN56-3\",,\"CN56-4\",,\"图7/8,纸输入电机M1 A相信号FEEDMTR-A\"
,,,,\"4\",\"M1\",,\"CN56-4\",,\"CN56-3\",,\"图7/8,纸输入电机M1 A/相信号FEEDMTR-A/\"
,,,,\"5\",\"M1\",,\"CN56-5\",,\"CN56-2\",,\"图7/8,纸输入电机M1 B相信号FEEDMTR-B\"
,,,,\"6\",\"M1\",,\"CN56-6\",,\"CN56-1\",,\"图7/8,纸输入电机M1 B/相信号FEEDMTR-B/\"
,,,,\"7\",\"M2\",,\"CN57-1\",,\"CN57-6\",,\" 24V\"
,,,,\"8\",\"M2\",,\"CN57-2\",,\"CN57-5\",,\" 24V\"
,,,,\"9\",\"M2\",,\"CN57-3\",,\"CN57-4\",,\"图8/8,蹼轮步进(将纸拉入堆垛处理盘)电机M2 A相信号PDLMTR-A\"
,,,,\"10\",\"M2\",,\"CN57-4\",,\"CN57-3\",,\"图8/8,蹼轮步进(将纸拉入堆垛处理盘)电机M2 A/相信号PDLMTR-A/\"
,,,,\"11\",\"M2\",,\"CN57-5\",,\"CN57-2\",,\"图8/8,蹼轮步进(将纸拉入堆垛处理盘)电机M2 B相信号PDLMTR-B\"
,,,,\"12\",\"M2\",,\"CN57-6\",,\"CN57-1\",,\"图8/8,蹼轮步进(将纸拉入堆垛处理盘)电机M2 B/相信号PDLMTR-B/\"
,,,,\"CN11\",\"接装订部件\"
,,,,\"1\",\"STPL-CNCT/\",,,,\"CN72A-7\",,\"CN72-7\",,\"图4/8,装订部件接入检测信号STPL-CNCT/\"
,,,,\"2\",\" 5V\",,,,\"CN72A-6\",,\"CN72-6\",,\" 5V\"
,,,,\"3\",\"SLID-HP\",,,,\"CN72A-5\",,\"CN72-5\",,\"图4/8,装订器滑动步进电机M8原位传感器SLID-HP\"
,,,,\"4\",\"STPL-HP\",,,,\"CN72A-4\",,\"CN72-4\",,\"图4/8,装订器原位传感器STPL-HP\"
,,,,\"5\",\"HOOK-S\",,,,\"CN72A-3\",,\"CN72-3\",,\"图4/8,装订器钉空传感器HOOK-S\"
,,,,\"6\",\"SELF-P\",,,,\"CN72A-2\",,\"CN72-2\",,\"图4/8,装订器钉位置传感器SELF-P\"
,,,,\"7\",\"GND\",,,,\"CN72A-1\",,\"CN72-1\",,\"GND\"
,,,,\"CN7\",\"接装订部件\"
,,,,\"1\",\" 24V\",,,,\"CN72B-7\",,\"CN72-8\",,\" 24V\"
,,,,\"2\",\" 24V\",,,,\"CN72B-6\",,\"CN72-9\",,\" 24V\"
,,,,\"3\",\"M8\",,,,\"CN72B-5\",,\"CN72-10\",,\"图7/8,装订器滑动步进电机M8 A相信号SLIDMTR-A\"
,,,,\"4\",\"M8\",,,,\"CN72B-4\",,\"CN72-11\",,\"图7/8,装订器滑动步进电机M8 A/相信号SLIDMTR-A/\"
,,,,\"5\",\"M8\",,,,\"CN72B-3\",,\"CN72-12\",,\"图7/8,装订器滑动步进电机M8 B相信号SLIDMTR-B\"
,,,,\"6\",\"M8\",,,,\"CN72B-2\",,\"CN72-13\",,\"图7/8,装订器滑动步进电机M8 B/相信号SLIDMTR-B/\"
,,,,\"7\",\"M8\",,,,\"CN72B-1\",,\"空\"
,,,,\"CN13\"
,,,,\"1\",\"M3\",,,,\"CN59-1\",,\"CN59-6\",,\" 24V\"
,,,,\"2\",\"M3\",,,,\"CN59-2\",,\"CN59-5\",,\" 24V\"
,,,,\"3\",\"M3\",,,,\"CN59-3\",,\"CN59-4\",,\"图7/8,纸堆垛处理盘的排纸步进电机M3 A相信号EJCTMTR-A\"
,,,,\"4\",\"M3\",,,,\"CN59-4\",,\"CN59-3\",,\"图7/8,纸堆垛处理盘的排纸步进电机M3 A/相信号EJCTMTR-A/\"
,,,,\"5\",\"M3\",,,,\"CN59-5\",,\"CN59-2\",,\"图7/8,纸堆垛处理盘的排纸步进电机M3 B相信号EJCTMTR-B\"
,,,,\"6\",\"M3\",,,,\"CN59-6\",,\"CN59-1\",,\"图7/8,纸堆垛处理盘的排纸步进电机M3 B/相信号EJCTMTR-B/\"
,,,,\"CN15\"
,,,,\"1\",\" 5V\",,,,,,,,\"CN47-3\",,\" 5V\"
,,,,\"2\",\"GND\",,,,,,,,\"CN47-2\",,\"GND\"
,,,,\"3\",\"BIND-EMPS\",,,,,,,,\"CN47-1\",,\"PI13\",\"图4/8,鞍式装订对折纸接纸盘纸空传感器信号 CN15-3 BIND-EMPS\"
,,,,\"4\",\" 5V\",,,,,,,,\"CN48-3\",,\" 5V\"
,,,,\"5\",\"GND\",,,,,,,,\"CN48-2\",,\"GND\"
,,,,\"6\",\"SIFT-CLK\",,,,,,,,\"CN48-1\",,\"PI17\",\"图4/8,接纸托盘(shift)电机M6时钟传感器PI17,SIFT-CLK\"
,,,,\"7\",\" 5V\",,,,,,,,\"CN49-3\",,\" 5V\"
,,,,\"8\",\"GND\",,,,,,,,\"CN49-2\",,\"GND\"
,,,,\"9\",\"SIFT-DNLMT\",,,,,,,,\"CN49-1\",,\"PI16\",\"图4/8,接纸托盘下限传感器PI17,SIFT-DNLMT\"
,,,,\"10\",\" 5V\",,,,,,,,\"CN50-3\",,\" 5V\"
,,,,\"11\",\"GND\",,,,,,,,\"CN50-2\",,\"GND\"
,,,,\"12\",\"SIFT-UPLMT\",,,,,,,,\"CN50-1\",,\"PI15\",\"图4/8,接纸托盘上限传感器PI15,SIFT-UPLMT\"
,,,,\"CN16\"
,,,,\"1\",\" 5V\",,,,\"CN37-9\",,\"CN38-1\",,\"CN39-3\",,\" 5V\"
,,,,\"2\",\"BIND-P\",,,,\"CN37-8\",,\"CN38-2\",,\"CN39-2\",,,\"图6/8,对折纸位置传感器光接收←CN16-2 BIND-P\"
,,,,\"3\",\"BIND-L\",,,,\"CN37-7\",,\"CN38-3\",,\"CN39-1\",,\"PI10\",\"图6/8,对折纸位置传感器光发射→CN16-3 BIND-L\"
,,,,\"4\",\" 5V\",,,,\"CN37-6\",,\"CN38-4\",,\"CN40-3\",,\" 5V\"
,,,,\"5\",\"GND\",,,,\"CN37-5\",,\"CN38-5\",,\"CN40-2\",,\"GND\"
,,,,\"6\",\"BIND-HP\",,,,\"CN37-4\",,\"CN38-6\",,\"CN40-1\",,\"PI11\",\"图6/8,BIND-POS-对折纸折纸板原位传感器信号 BIND-HP\"
,,,,\"7\",\" 5V\",,,,\"CN37-3\",,\"CN38-7\",,\"CN41-3\",,\" 5V\"
,,,,\"8\",\"GND\",,,,\"CN37-2\",,\"CN38-8\",,\"CN41-2\",,\"GND\"
,,,,\"9\",\"BIND-ROL-HP\",,,,\"CN37-1\",,\"CN38-9\",,\"CN41-1\",,\"PI12\",\"图6/8,鞍式装订堆垛纸进纸轮(上)原位传感器信号 BIND-ROL-HP,CN16-9\"
,,,,\"10\",\" 5V\",,,,\"CN42-3\",,\"CN43-1\",,\"CN44-3\",,\" 5V\"
,,,,\"11\",\"GND\",,,,\"CN42-2\",,\"CN43-2\",,\"CN44-2\",,\"GND\"
,,,,\"12\",\"ENT-S\",,,,\"CN42-1\",,\"CN43-3\",,\"CN44-1\",,\"PI1\",\"图5/8,纸进入(鞍式分页器-G1)检测传感器信号ENT-S\"
,,,,\"CN17\",,\"图2/8,\"
,,,,\"1\",\"SGND\"
,,,,\"2\",\"TXD2\",,,,\"图2/8,数据接收信号-2 RXD-2(CN17-2)\"
,,,,\"3\",\"RXD2\",,,,\"图2/8,数据发送信号-2 TXD-2(CN17-3)\"
,,,,\"4\",\"DSR\"
,,,,\"5\",\"RTR\"
,,,,\"6\",\"RES\"
,,,,\"CN18\"
,,,,\"1\",\" 24V\",,,,,,\"CN72-2\",,\"CN72-1\",,\" 24V\"
,,,,\"2\",\"B-CLU\",,,,,,\"CN72-1\",,\"CN72-2\",,\"CL1\",\"图7/8,鞍式装订输送纸堆垛轮离合器,B-CLU/\"
,,,,\"CN19\"
,,,,\"1\",\" 5V\",,,,,,,,\"CN73-3\",,\" 5V\"
,,,,\"2\",\"GND\",,,,,,,,\"CN73-2\",,\"GND\"
,,,,\"3\",\"PAPER-F\",,,,,,,,\"CN73-1\",,\"PI24\",\"图4/8,接纸盘纸堆满传感器信号 PAPER-F 1:堆垛满\"
,,,,\"CN12\",,\"接Puncher打孔单元\"
,,,,\"1\",,,,\"CN12-1\",,,\"J2003-10\",,\"J1003-10\",,,\"图2/8,CN12-1,Puncher打孔单元数据发送信号PNCH-TXD\"
,,,,\"2\",,,,\"CN12-2\",,,\"J2003-9\",,\"J1003-9\",,,\"SGND\"
,,,,\"3\",,,,\"CN12-3\",,,\"J2003-8\",,\"J1003-8\",,,\"图2/8,CN12-3,Puncher打孔单元数据接收信号PNCH-RXD\"
,,,,\"4\",,,,\"CN12-4\",,,\"J2003-7\",,\"J1003-7\",,,\"图2/8,CN12-4,Puncher打孔单元接入检测信号PNCH-CNCT/\"
,,,,\"5\",,,,\"CN12-5\",,,\"J2003-6\",,\"J1003-6\",,,\"打孔原位传感器PI1P←图2/8,CN12-5,PNCH-TIM-S\"
,,,,\"6\",,,,\"CN12-6\",,,\"J2003-5\",,\"J1003-5\"
,,,,\"7\",,,,\"CN12-7\",,,\"J2003-4\",,\"J1003-4\"
,,,,\"8\",,,,\"CN12-8\",,,\"J2003-3\",,\"J1003-3\"
,,,,\"9\",,,,\"CN12-9\",,,\"J2003-2\",,\"J1003-2\"
,,,,\"10\",,,,\"CN12-10\",,,\"J2003-1\",,\"J1003-1\"
,,,,\"CN14\",,\"接Puncher打孔单元\"
,,,,\"1\",,\" 5V\",,\"CN14-1\",,\"→\",\"J2004-1\",,\"J1004-1\"
,,,,\"2\",,\"SGND\",,\"CN14-2\",,\"→\",\"J2004-2\",,\"J1004-2\"
,,,,\"3\",,\"PGND\",,\"CN14-3\",,\"→\",\"J2004-3\",,\"J1004-3\"
,,,,\"4\",,\"空\",,\"CN14-4\",,\"→\",\"J2004-4\",,\"J1004-4\"
,,,,\"5\",,\" 24V\",,\"CN14-5\",,\"→\",\"J2004-5\",,\"J1004-5\"
,,,,,,,,,,\"←\"
,,,,,,\"Puncher打孔单元主板\"
,,,,\"J1001\"
,,,,\"1\",,,,\"J1001-1\"
,,,,\"2\",,,,\"J1001-2\",,,\"J2001-4\",,\"M2P\"
,,,,\"3\",,,,\"J1001-3\",,,\"J2001-3\"
,,,,\"4\",,,,\"J1001-4\",,,\"J2001-2\"
,,,,\"5\",,,,\"J1001-5\",,,\"J2001-1\"
,,,,\"J1002\"
,,,,\"1\",,,,\"J1002-1\",,,\"J2002-1\",,\"M1P\"
,,,,\"2\",,,,\"J1002-2\",,,\"J2002-2\"
,,,,\"J1005\"
,,,,\"1\",,,,\"J1005-1\",,,\"J2005-2\"
,,,,\"2\",,,,\"J1005-2\",,,\"J2005-1\"
,,,,\"3\",,,,\"J1005-3\",,,\"J2006-2\"
,,,,\"4\",,,,\"J1005-4\",,,\"J2006-1\"
,,,,\"J1006\"
,,,,\"1\",\" 5V\",,,\"J2007-3\",,\" 5V\"
,,,,\"2\",\"SGND\",,,\"J2007-2\",,\"SGND\"
,,,,\"3\",\"SLIDE\",,,\"J2007-1\",,\"PI2P\",\"图4.1,水平(横向)对位原位传感器信号SLIDE\"
,,,,\"4\",\" 5V\",,,\"J2008-3\",,\" 5V\"
,,,,\"5\",\"SGND\",,,\"J2008-2\",,\"SGND\"
,,,,\"6\",\"PUNCH\",,,\"J2008-1\",,\"PI1P\",\"图4.1,打孔器原位传感器信号PUNCH\"
,,,,\"7\",\" 5V\",,,\"J2009-3\",,\" 5V\"
,,,,\"8\",\"SGND\",,,\"J2009-2\",,\"SGND\"
,,,,\"9\",\"CLOCK\",,,\"J2009-1\",,\"PI3P\",\"图4.1,打孔器电机时钟传感器信号CLOCK\"
,,,,\"J1007\"
,,,,\"1\",,,,\"J1007-1\",,\"J2010-6\",,\"YR LED\"
,,,,\"2\",,,,\"J1007-2\",,\"J2010-5\",,\"R1 LED1\"
,,,,\"3\",,,,\"J1007-3\",,\"J2010-4\",,\"R1 LED2\"
,,,,\"4\",,,,\"J1007-4\",,\"J2010-3\",,\"R1 LED3\"
,,,,\"5\",,,,\"J1007-5\",,\"J2010-2\",,\"R1 LED4\"
,,,,\"6\",,,,\"J1007-6\",,\"J2010-1\",,\" 5V\"
,,,,\"7\",,,,\"J1007-7\",,\"J2011-7\",,\"Y REG1\"
,,,,\"8\",,,,\"J1007-8\",,\"J2011-6\",,\"B5R\"
,,,,\"9\",,,,\"J1007-9\",,\"J2011-5\",,\"A4R\"
,,,,\"10\",,,,\"J1007-10\",,\"J2011-4\",,\"B4\"
,,,,\"11\",,,,\"J1007-11\",,\"J2011-3\",,\"A4\"
,,,,\"12\",,,,\"J1007-12\",,\"J2011-2\",,\" 5V\"
,,,,\"13\",,,,\"J1007-13\",,\"J2011-1\",,\"SGND\"
\"iR5000维修报告\"
\"制作:WGF\"
\"共页, 第页\"
,,,,,,,,,,\"CANON 佳能 iR5000/iR6000 数码复印机维修报告\"
,,,,,,\"选择COPIRE >FUNCTION>MISC-P>P-PRINT按OK键,打印出打印维修模式一览表\"
,,,,,,,,,\"COPY SERVICE REPORT\",,,,,,,,\"单位\",,,,,,,,\"机号\"
,\"ADJUST\",,,\"调整\"
,\"AE\",,,\"自动曝光调整\",,,,,,,\"5-45T\",,,,,,\"调整范围\",,,,\"当前值\"
,\"AE-TBL\",,,\"AE模式的文字浓度调整\",,,,,,,,,,,,,\"1～9\",,,,\"5\"
,\"ADJ-XY\",,,\"扫描位置调整\"
,\"ADJ-X\",,,\"副扫描方向图像读取开始位置调整\",,,,,,,,,,,,,\"250～290\",,,,\"281\"
,\"ADJ-Y\",,,\"主扫描方向图像读取开始位置调整\",,,,,,,,,,,,,\"100～400\",,,,\"202\"
,\"ADJ-S\",,,\"光学原位位置调整(HP传感器)\",,,,,,,,,,,,,\"55～70\",,,,\"62\"
,\"ADJ-Y-DF\",,,\"ADF主扫描方向图像读取开始位置调整\",,,,,,,,,,,,,\"100～400\",,,,\"234\"
,\"STRD-POS\",,,\"用ADF移动扫描时CCD读取位置的调整\",,,,,,,,,,,,,\"30～60\",,,,\"27\"
,\"CCD\",,,\"CCD电信号补偿正时的调整\"
,\"SH-TRGT\",,,\"白色程度目标值输入\",,,,,,,,,,,,,,,,,\"188\"
,\"SH-RATIO\",,,\"标准白色纸与标准白板之比率数据值输入\",,,,,,,,,,,,,,,,,\"211\"
,\"EGGN-ST\",,,\"CCD的顶端放大补正开始位置调整值输入\",,,,,,,,,,,,,,,,,\"176\"
,\"EGGN-END\",,,\"CCD的顶端放大补正结束位置调整值输入\",,,,,,,,,,,,,,,,,\"180\"
,\"LASER\",,,\"激光调整\"
,\"PVE-OFST\",,,\"激光位置的调整(Ofst)\",,,,,,,,,\"(23大约1毫米)\",,,,\"-300～ 300\",,,,\"5\"
,\"POWER\",,,\"非电位控制时的激光电源调整\",,,,,,,,,,,,,\"0～255\",,,,\"124\"
,\"DEVELOP\",,,\"显影偏压调整\"
,\"BIAS\",,,\"显影偏压DC输出值的调整值输入\",,,,,,,,,,,,,\"0浓～600淡\",,,,\"180\"
,\"HVT-DE\",,,\"高压组件上的显影偏压输出的补偿值输入\",,,,,,,,,,,,,\"-100淡～ 100浓\",,,,\"1\"
,\"D-HV-DE\",,,\"DC控制板上的显影偏压输出的补偿值输入\",,,,,,,,,,,,,\"-100淡～ 100浓\",,,,\"-10\"
,\"DENS\",,,\"浓度调整\"
,\"DENS-ADJ\",,,\"复印/打印浓度自动补正的微调整\",,,,,,,,,,,,,\"1～9,缺省值=5\",,,,\"5\"
,\"BLANK\",,,\"空白调整\"
,\"BLANK-T\",,,\"图像前端缺损宽度调整值输入\",,,,,,,,,,,,,\"1～500\",,,,\"40\"
,\"BLANK-B\",,,\"图像后端缺损宽度调整值输入\",,,,,,,,,,,,,,,,,\"25\"
,\"V-CONT \",,,\"电位控制\"
,\"EPOTOFST\",,,\"电位传感器的补偿值输入\",,,,,,,,,,,,,\"0～255\",,,,\"15\"
,\"VD-OFST\",,,\"复印用VD目标电位的补偿值输入\",,,,,,,,,,,,,\"-5～ 5\",,,,\"0\"
,\"DE-OFS-P\",,,\"打印(PDL)用VL目标电位的补偿值输入(Vdc微调整)\",,,,,,,,,,,,,\"-50～ 50\",,,,\"0\"
,\"VD-OFS-P\",,,\"打印(PDL)用VD目标电位的补偿值输入(Vdc微调整)\",,,,,,,,,,,,,\"-5～ 5\",,,,\"0\"
,\"DE-OFST\",,,\"复印用VL目标电位的补偿值输入(Vdc微调整)\",,,,,,,,,,,,,\"-50～ 50\",,,,\"0\"
,\"HV-PRI\",,,\"一次带电调整\"
,\"PRIMARY\",,,\"非电位控制时的一次电流的调整值输入\",,,,,,,,,,,,,\"0～1400\",,,,\"666\"
,\"HV-TR\",,,\"转印高压调整\"
,\"TR-N1\",,,\"第1面,转印正高压电流维修标签上的调整值输入\",,,,,,,,,,,,,,,,,\"350\"
,\"TR-N2\",,,\"第2面,转印正高压电流维修标签上的调整值输入\",,,,,,,,,,,,,,,,,\"290\"
,\"PRE-TR \",,,\"预转印高压电流维修标签上的调整值输入\",,,,,,,,,,,,,,,,,\"-200\"
,\"HVT-TR\",,,\"转印高压组件维修标签上转印正电流调整值输入\",,,,,,,,,,,,,,,,,\"1\"
,\"H-PRE-TR\",,,\"预转印高压组件维修标签上预转印电流调整值输入\",,,,,,,,,,,,,,,,,\"0\"
,\"D-PRV-TR\",,,\"DC控制板维修标签预转印高压电流的补偿值输入\",,,,,,,,,,,,,,,,,\"-1\"
,\"D-HV-TR\",,,\"DC控制板维修标签转印高压电流的补偿值输入\",,,,,,,,,,,,,,,,,\"-1\"
,,,,,,,,,,\"CANON 佳能 iR5000/iR6000 数码复印机维修报告\"
,,,,,,\"选择COPIRE >FUNCTION>MISC-P>P-PRINT按OK键,打印出打印维修模式一览表\"
,,,,,,,,,\"COPY SERVICE REPORT\",,,,,,,,\"单位\",,,,,,,,\"机号\"
,\"HV-SP\",,,\"分离高压调整\"
,\"SP-N1\",,,\"维修标签上的第1面,分离负高压电流的调整值输入\",,,,,,,,,,,,,,,,,\"-83\"
,\"SP-N2\",,,\"维修标签上的第2面,分离负高压电流的调整值输入\",,,,,,,,,,,,,,,,,\"-83\"
,\"HVT-SP\",,,\"高压组件维修标签上分离负高压电流的调整值输入\",,,,,,,,,,,,,,,,,\"2\"
,\"D-HV-TR\",,,\"DC控制板维修标签上分离负电流的调整值输入\",,,,,,,,,,,,,,,,,\"-1\"
,\"FEED-ADJ\",,,\"进纸时序调整\"
,\"REGIST\",,,\"对位离合器ON时序调整\",,,,,,,,,\"每步0.1毫米\",,,,\"-50～ 50\",,,,\"5\"
,\"ADJ-REFE\",,,\"再进纸时横向对位调整\",,,,,,,,,\"每步0.1毫米\",,,,\"-50～ 50\"
,\"RG-MF\",,,\"手送纸盘进纸时对位离合器ON调整\",,,,,,,,,\"每步0.1毫米\",,,,\"-50～ 50\",,,,\"10\"
,\"CST-ADJ\",,,\"纸盒/手送纸设置\"
,\"C3-STMTR\",,,\"纸盒3的STMTR纸尺寸宽度设定 \",,,,,,,,,,,,,,,,,\"14\"
,\"C3-A4R\",,,\"纸盒3的A4-R纸尺寸宽度设定 \",,,,,,,,,,,,,,,,,\"113\"
,\"C4-STMTR\",,,\"纸盒4的STMTR纸尺寸宽度设定\",,,,,,,,,,,,,,,,,\"12\"
,\"C4-A4R\",,,\"纸盒4的A4-R纸尺寸宽度设定 \",,,,,,,,,,,,,,,,,\"110\"
,\"MF-A4R\",,,\"50张手进纸盘纸宽度基本数值设置\",,,,,,,,,,,,,\"A4R\",,,,\"111\"
,\"MF-A6R\",,,\"50张手进纸盘纸宽度基本数值设置\",,,,,,,,,,,,,\"A6R\",,,,\"225\"
,\"MF-A4\",,,\"50张手进纸盘纸宽度基本数值设置\",,,,,,,,,,,,,\"A4R\",,,,\"17\"
,\"C3-LVOL\",,,\"纸盒3的纸容量设定(50张) \",,,,,,,,,,,,,,,,,\"91\"
,\"C3-HVOL\",,,\"纸盒3的纸容量设定(275张) \",,,,,,,\" \",,,,,,,,,,\"139\"
,\"C4-LVOL\",,,\"纸盒4的纸容量设定(50张) \",,,,,,,,,,,,,,,,,\"88\"
,\"C4-HVOL\",,,\"纸盒4的纸容量设定(275张) \",,,,,,,,\" \",,,,,,,,,\"136\"
,\"MISC\",,,\"其他调整\"
,\"ATM\",,,\"气压低容易漏电要降低电位控制的目标电位\",,,,,,,,,,,,,\"0～2\",,,,\"0:1～0.75气压(2500米以下地区); \"
,\"OPTION \",,,\"机器功能设定模式\"
,\"BODY\",,,\"与主机有关的功能设定模式\",,,,,,,,,,,,,,,,,\"调整范围\",,,,\"当前值\"
,\"PO-CNT\",,,\"电位控制的ON/OFF设定\",,,,,,,,,,,,,,,,,\"0:0FF\",,\"1:ON\",,\"1\"
,\"PO-CNTMD\",,,\"电位控制的模式设定\",,,,,,,,,,,,,,,,,\"0～2\",,,,\"0\"
,,,,,\"0:仅在电源ON时执行一次(缺省值); \"
,,,,,\"1:电源ON后10分和60分钟时执行(缩短模式); \"
,,,,,\"2:电源ON后10分和60分钟时执行(普通模式)\"
,\"W-CLN-P\",,,\"电极丝的自动清洁间隔设定\",,,,,,,,,,,,,,,,,\"100～2000张\",,,,\"2000张\"
,\"MODEL-SZ\",,,\"规格/固定倍率/尺寸模式设定\",,,,,,,,,,,,,,,,,\"0～3\",,,,\"3\"
,,,,,\"0:AB;1:英制;2:A;3:AB/英制\"
,\"FIX-TEMP\",,,\"定影温度设定值\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,,,,,\"0:OFF(缺省值)\"
,,,,,\"1:定影性优先,下降顺序温度一律 10度;\"
,,,,,\":生产性优先,下降顺序温度一律-10度;\"
,\"IDL-MODE\",,,\"定影空转模式设定\",,,,,,,,,,,,,,,,,\"0～3\",,,,\"0\"
,,,,,\"0:定影不空转(缺省值)\"
,,,,,\"1:根据环境传感器自动控制;\"
,,,,,\"2 :定影温度达到100度开始定影空转 ; \"
,,,,,\"3: 电源开关ON时就开始定影空转\"
,\"FSPD--S1\",,,\"特殊纸定影温度设定\",,,,,,,,,,,,,,,,,\"0～2\",,,,\"0\"
,,,,,\"0:正常(普通复印纸)模式(缺省值)\"
,,,,,\"1:特殊纸张模式1(高湿度环境时,降低定影温度) ;\"
,,,,,\"2:特殊纸张模式(厚纸)\"
,,,,,,,,,,\"CANON 佳能 iR5000/iR6000 数码复印机维修报告\"
,,,,,,\"选择COPIRE >FUNCTION>MISC-P>P-PRINT按OK键,打印出打印维修模式一览表\"
,,,,,,,,,\"COPY SERVICE REPORT\",,,,,,,,\"单位\",,,,,,,,\"机号\"
,\"OPTION \",,,\"机器功能设定模式\"
,\"FUZZY\",,,\"模糊控制的ON/OFF和环境设定\",,,,,,,,,,,,,,,,,\"0～3\"
,,,,,\"0:预转印/转印/分离电流进行模糊控制(缺省值)\"
,,,,,\"1:低湿度环境模式(输出的电流低于标准值) ;\"
,,,,,\"2:正常湿度环境模式(输出的电流为标准值) ;\"
,,,,,\"3高湿度环境模式(输出的电流高于标准值)\"
,\"TSPLY-SW\",,,\"根据环境传感器的湿度自动控制补粉的选择\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,,,,,\"0:自动控制补粉,中/低湿度2秒ON,1秒OFF;\"
,,,,,\"高湿度4秒ON,2秒OFF(缺省值) \"
,,,,,\"1:固定模式,2秒ON,1秒OFF\"
,\"SCZNSLCT\",,,\"ADF的原稿尺寸检测的ON/OFF\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,,,,,\"0:OFF;1:ON 根据原稿尺寸决定扫描尺寸\"
,\"OHP-TNMP\",,,\"胶片模式定影温度降低的设定\",,,,,,,,,,,,,,,,,\"0～3\",,,,\"0\"
,,,,,\"0:正常(普通复印纸)模式(缺省值)\"
,,,,,\"1:通常温度降5度;2:通常温度降10度;\"
,,,,,\"3:通常温度降15度;4:通常温度降20度;\"
,,,,,\"注:FSPD-S1或WARM-UP不为0该项更改无效\"
,\"F-GD-CNT\",,,\"定影入口导板下降设定\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,,,,,\"0:正常模式(缺省值) ;\"
,,,,,\"1:A4R以上,仅第1面降低定影入口导板\"
,\"CONFIG\",,,\"硬盘使用地,国家,语言,纸尺寸设定\"
,,,,,\"按照DISPLAY>USER>LANGUAGE的方法显示\"
,\"WARM-UP\",,,\"室温在18度以上定影预热时间的设定\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,,,,,\"0:正常模式(缺省值) ;\"
,,,,,\"1:前旋转开始/待机/打印开始温度一律下降15度\"
,\"SHARP\",,,\"图像清晰度电平设定\",,,,,,\"数值大清晰度高(焦距增大)\",,,,,,,,,,,\"1～5\",,,,\"3\"
,\"LAPC-SW\",,,\"激光自动功率控制(APC)补正的设定\",,,,,,,,,,,,,,,,,\"0～4\",,,,\"1\"
,,,,,\"0:0N(10分钟无操作进行前旋转APC)\"
,,,,,\"1:0N(60分钟无操作进行前旋转APC),缺省值\"
,,,,,\"2:0N(120分钟无操作进行前旋转APC)\"
,,,,,\"3:只有前旋转APC为OFF ;\"
,,,,,\"4:OFF\"
,\"COTDPC-D\",,,\"工厂调整用\",,,,,,,,,,,,,,,,,\"0～3\",,,,\"0\"
,\"EVL-VDT\",,,\"多份打印时改为纸反面排出\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"1\"
,,,,,\"0:普通(1张原稿时全部正面排纸)缺省值;\"
,,,,,\"1:1张原稿打印1份正面排纸,打印多份纸反面排出\"
,\"BODY\",,,\"与主机有关的功能设定模式\",,,,,,,,,,,,,,,,,\"调整范围\",,,,\"当前值\"
,\"RMT-LANG\",,,\"改变通过网络使用的遥控用户界面的语言\"
,,,,,\"语言代码按照COPIER>DISPLAY>USER\"
,,,,,\">LANGUAGE(语言)的显示方法\"
,,,,,\"操作法:1,选择RMT-LANG; \"
,,,,,\"2,每按一次\\\" /-\\\"键,语言代码按次序变化\"
,,,,,\"3,选择到要用的语言代码时,按OK键\"
,\"HI-HUME\",,,\"湿度高分离不良时显影偏压频率的改变\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,,,,,\"0:2700HZ(缺省值) ;1:2000HZ\"
,\"TR-SP-C1\",,,\"为对应各种故障改变右前置纸仓的转印/分离输出值\",,,,,,,,,,,,,,,,,\"0～3\",,,,\"0\"
,,,,,\"0:正常模式(缺省值);1:防止再转印;\"
,,,,,\"2:防止分离不良;3:防止漏转印\"
,,,,,,,,,,\"CANON 佳能 iR5000/iR6000 数码复印机维修报告\"
,,,,,,\"选择COPIRE >FUNCTION>MISC-P>P-PRINT按OK键,打印出打印维修模式一览表\"
,,,,,,,,,\"COPY SERVICE REPORT\",,,,,,,,\"单位\",,,,,,,,\"机号\"
,\"BODY\",,,\"与主机有关的功能设定模式\",,,,,,,,,,,,,,,,,\"调整范围\",,,,\"当前值\"
,\"TR-SP-C2\",,,\"为对应各种故障改变左前置纸仓的转印/分离输出值\",,,,,,,,,,,,,,,,,\"0～3\",,,,\"0\"
,\"TR-SP-C3\",,,\"为对应各种故障改变前置纸盒3的转印/分离输出值\",,,,,,,,,,,,,,,,,\"0～3\",,,,\"0\"
,\"TR-SP-C4\",,,\"为对应各种故障改变前置纸盒4的转印/分离输出值\",,,,,,,,,,,,,,,,,\"0～3\",,,,\"0\"
,\"TR-SP-MF\",,,\"为对应各种故障改手送纸盘的转印/分离输出值\",,,,,,,,,,,,,,,,,\"0～3\",,,,\"0\"
,\"TR-SP-DK\",,,\"为对应各种故障改右侧纸仓(G1)的转印/分离输出值\",,,,,,,,,,,,,,,,,\"0～3\",,,,\"0\"
,\"TPR-DECL\",,,\"厚纸反转排纸动作时改变排纸路径提高输出效果\",,,,,,,,,,,,,,,,,\"0～3\",,,,\"0\"
,\"DF-BLINE\",,,\"移动扫描时的黑线减弱模式的ON/OFF\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,,,,,\"0:OFF(缺省值) ;1:ON 打印图像的边缘\"
,\"USER\",,,\"与用户模式有关的功能设定模式\"
,\"COPY-LIM\",,,\"复印张数上限设定\",,,,,,,,,,,,,,,,,\"1～999\",,,,\"999\"
,\"SLEEP\",,,\"睡眠功能设定\",,,,,,,,,,,,,,,,,\"0:OFF\",,\"1:ON\",,\"1\"
,\"WEB-DISP\",,,\"定影清洁纸少时在基本画面出现警告提示\",,,,,,,,,,,,,,,,,\"0:OFF\",,\"1:ON\",,\"0\"
,\"SIZE-DET\",,,\"原稿尺寸检测功能的ON/OFF设定\",,,,,,,,,,,,,,,,,\"0:OFF\",,\"1:ON\",,\"0\"
,\"W-TONER\",,,,,,,,,,,,,,,,,,,,,,,,\"0\"
,\"COUNTER1\",,,\"操作面板软计数器1的类型显示\",,,,,,,,,,,,,,,,,,,,,\"101\"
,\"COUNTER2\",,,\"操作面板软计数器2的类型设定\",,,,,,,,,,,,,,,,,,,,,\"103\"
,\"COUNTER3\",,,\"操作面板软计数器3的类型设定\",,,,,,,,,,,,,,,,,,,,,\"201\"
,\"COUNTER4\",,,\"操作面板软计数器4的类型设定\",,,,,,,,,,,,,,,,,,,,,\"203\"
,\"COUNTER5\",,,\"操作面板软计数器5的类型设定\",,,,,,,,,,,,,,,,,,,,,\"000\"
,\"COUNTER6\",,,\"操作面板软计数器6的类型设定\",,,,,,,,,,,,,,,,,,,,,\"000\"
,\"DATA-DSP\",,,\"日期/时间表示型式设定\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"1\"
,,,,,\"0:YYYY MM/DD缺省值\",,,,,,\"1:DD/MM YYYY\"
,\"MB-CCV\",,,\"信箱控制卡IV(CC-IV)使用者遥控时限制\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"1\"
,,,,,\"0:不受卡的限制,均可操作和打印,遥控不计费\"
,,,,,\"1:不受卡的限制,均可操作,可输入打印工作,\"
,,,,,\"但无控制卡不能打印(有卡可打印,但要计费)\"
,\"B4-L-CNT\",,,\"软计数器1～6使用B4纸时作为(L)/(S)计数设定\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,,,,,\"0:小尺寸(S)计数(缺省值);1:大尺寸(L)计数\"
,\"TRY-STP\",,,\"装订/混载限制而中断打印的禁止\",,,,,,,,,,,,,,,,,\"0～2\",,,,\"0\"
,,,,,\"0:正常模式[缺省值](因份数/混载限制中断打印)\"
,,,,,\"1:高度传感器ON(纸张满载)时中断打印\"
,,,,,\"2:遥控工作不能接受,也不能输入打印工作.\"
,\"MF-LG-ST\",,,\"使用手送纸盘纸尺寸加长键的设定(显示该键)\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,,,,,\"0:正常模式:1:纸尺寸加长(630毫米)模式(显示该键)\"
,\"SPECK-DP\",,,\"移动扫描用的异物检测结果的警告显示/不显示\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,,,,,\"0:不显示(缺省值);1:显示\"
,\"CNT-DISP\",,,\"按计数器确认键时的编号的显示/不显示\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,,,,,\"0:显示(缺省值);1:不显示\"
,\"PH-D-SEL\",,,\"照片模式打印的线数选择\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,,,,,\"0:141线(缺省值);1:134线\"
,\"COPY-JOB\",,,\"使用控制卡或投币器时的复印工作预约的禁止\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,,,,,\"0:有复印工作预约(缺省值);1:无复印工作预约\"
,\"OP-SZ-DT\",,,\"书本模时的原稿尺寸检测的ON/OFF\"
,,,,,\"0:OF(缺省值);\",,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,,,,,\"1:ON(自动检测原稿尺寸)\"
,,,,,,,,,,\"CANON 佳能 iR5000/iR6000 数码复印机维修报告\"
,,,,,,\"选择COPIRE >FUNCTION>MISC-P>P-PRINT按OK键,打印出打印维修模式一览表\"
,,,,,,,,,\"COPY SERVICE REPORT\",,,,,,,,\"单位\",,,,,,,,\"机号\"
,\"CST\",,,\"与纸盒有关的功能设定模式\",,,,,,,,,,,,,,,,,\"调整范围\",,,,\"当前值\"
,\"U1-NAME\",,,\"检测到纸尺寸组U1时的纸名称表示的ON/OFF\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,,,,,\"0:OFF时,液晶显示U1(缺省值);\"
,,,,,\"1:ON时,液晶显示(CST-U1)所指定的纸张名称\"
,\"U2-NAME\",,,\"检测到纸尺寸组U2时的纸名称表示的ON/OFF\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,\"U3-NAME\",,,\"检测到纸尺寸组U3时的纸名称表示的ON/OFF\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,\"U4-NAME\",,,\"检测到纸尺寸组U4时的纸名称表示的ON/OFF\",,,,,,,,,,,,,,,,,\"0～1\",,,,\"0\"
,\"CST-U1\",,,\"纸尺寸组U1使用的纸尺寸名称设定\",,,,,,,,,,,,,,,,,,,,,\"31\"
,\"CST-U2\",,,\"纸尺寸组U2使用的纸尺寸名称设定\",,,,,,,,,,,,,,,,,,,,,\"24\"
,\"CST-U3\",,,\"纸尺寸组U3使用的纸尺寸名称设定\",,,,,,,,,,,,,,,,,,,,,\"34\"
,\"CST-U4\",,,\"纸尺寸组U4使用的纸尺寸名称设定\",,,,,,,,,,,,,,,,,,,,,\"18\"
,\"P-SZ-C1\",,,\"右前置纸仓(1500张)的纸尺寸名称设定\",,,,,,,,,,,,,,,,,,,,,\"6\"
,\"P-SZ-C2\",,,\"左前置纸仓(1500张)的纸尺寸名称设定\",,,,,,,,,,,,,,,,,,,,,\"6\"
,\"P-SZ-C4\",,,\"纸盒4使用的纸尺寸名称设定(120/230V机型有效)\",,,,,,,,,,,,,,,,,,,,,\"4\"
\".\",,,,,,,,\"纸盒的纸名称(略称)表\"
,,,,\"号码\",,\"略称\",,\"尺寸\",,\"号码\",,\"略称\",,,\"尺寸\",,,,,,\"号码\",,\"略称\",,,\"尺寸\"
,,,,\"01\",,\"A1\",,\"A1\",,\"15\",,\"B5 \",,,\"B5 \",,,,,,\"29\",,\"A-LTR\",,,\"阿根廷LETTER \"
,,,,\"02\",,\"A2\",,\"A2\",,\"16\",,\"11×17\",,,\"11〃×17〃\",,,,,,\"30\",,\"A-LTTR\",,,\"阿根廷LETTER-R\"
,,,,\"03\",,\"A3R\",,\"A3R\",,\"17\",,\"LTRR\",,,\"LETTER-R\",,,,,,\"31\",,\"G-LTR\",,,\"官厅LETTER \"
,,,,\"04\",,\"A3\",,\"A3\",,\"18\",,\"LTR \",,,\"LETTER \",,,,,,\"32\",,\"G-LTRR\",,,\"官厅LETTER-R\"
,,,,\"05\",,\"A4R\",,\"A4R\",,\"19\",,\"STMT\",,,\"STATEMENT\",,,,,,\"33\",,\"A-LGL\",,,\"阿根廷LEGAL\"
,,,,\"06\",,\"A4\",,\"A4\",,\"20\",,\"STMTR\",,,\"STATEMENT-R\",,,,,,\"34\",,\"G-LGL\",,,\"官厅LEGAL\"
,,,,\"07\",,\"A5\",,\"A5\",,\"21\",,\"LGL\",,,\"LEGAL\",,,,,,\"35\",,\"FOLI\",,,\"FOLIO\"
,,,,\"08\",,\"A5R\",,\"A5R\",,\"22\",,\"K-LGL\",,,\"韩国官厅纸\",,,,,,\"36\",,\"A-OFI\",,,\"阿根廷OFFICIO\"
,,,,\"09\",,\"B1\",,\"B1\",,\"23\",,\"K-LGLR\",,,\"韩国官厅纸\",,,,,,\"37\",,\"M-OFI\",,,\"墨西哥OFFICIO\"
,,,,\"10\",,\"B2\",,\"B2\",,\"24\",,\"FLSC\",,,\"FOOLSCAP\",,,,,,\"38\"
,,,,\"11\",,\"B3\",,\"B3\",,\"25\",,\"A-FLS\",,,\"澳大利亚FOOLSCAP\",,,,,,\"39\"
,,,,\"12\",,\"B4R\",,\"B4R\",,\"26\",,\"OFI\",,,\"OFICIO\",,,,,,\"40\",,\"ALL\"
,,,,\"13\",,\"B4 \",,\"B4 \",,\"27\",,\"E-OFI\",,,\"厄瓜多尔OFFICIO\"
,,,,\"14\",,\"B5R\",,\"B5R\",,\"28\",,\"B-OFI\",,,\"玻利维亚OFFICIO\"
,\"ACC\",,,\"与选购件有关的功能设定模式\",,,,,,,,,,,,,,,,,\"调整范围\",,,,\"当前值\"
,\"COIN\",,,\"将控制面板控制卡设定为显示投币机(COIN)\",,,,,,,,,,,,,,,,,,,,,\"0\"
,,,,,\"0:OFF(缺省值)\",,,,,\"1:ON,显示投币机(COIN)\"
,\"DKP\",,,\"选购件3500张右侧纸仓(G1)的纸尺寸设定\",,,,,,,,,,,,,,,,,,,,,\"0\"
,,,,,\"0:A4(缺省值);1:B5;2:LTR 注:设定后要将电源开关OFF后再ON\"
,\"TEMPO\",,,\"电位/环境传感器出故障时的设定\"
,\"F-PDT-SW\",,,\"电位传感器出故障引起转印不良时设定的ON/OFF\",,,,,,,,,,,,,,,,,,,,,\"0\"
,,,,,\"0:OFF(缺省值)\",,,,,\"1:F-POT-D的设定有效\"
,\"F-POT-D\",,,\"电位传感器出故障引起转印不良时的设定\",,,,,,,,,,,,,,,,,,,,,\"0\"
,,,,,\"在F-POT-SW设定为1有效\",,,,,,,,\"0:文字原稿\"
,,,,,\"2:发生再转印(前端出现50毫米空白)时用\"
,\"F-HUM-SW\",,,\"环境传感器出故障时设定的ON/OFF\",,,,,,,,,,,,,,,,,,,,,\"0\"
,,,,,\"0:OFF(缺省值)\",,,,\"1:F-HOM-D的设定有效\"
,\"F-HUM-D\",,,\"机器使用地的环境湿度的设定\"
,,,,,\"在F-HUM-SW设定为1有效\",,,,,,,\"设定范围:30～99%(缺省值=35%)\",,,,,,,,,,,,,\"35\"
,,,,,,,,,,\"CANON 佳能 iR5000/iR6000 数码复印机维修报告\"
,,,,,,\"选择COPIRE >FUNCTION>MISC-P>P-PRINT按OK键,打印出打印维修模式一览表\"
,,,,,,,,,\"COPY SERVICE REPORT\",,,,,,,,\"单位\",,,,,,,,\"机号\"
,,,,,,,,\"COUNTER\",,,,\"计数器\"
,\"TOTAL\",,,,\"总计数器\"
,,,,,\"SETVICE1\",,,\"维修总计数器1\"
,,,,,\"SETVICE2\",,,\"维修总计数器2\"
,,,,,\"COPY\",,,\"复印总计数器\"
,,,,,\"PDL-PRT\",,,\"PDL打印总计数器\"
,,,,,\"FAX-PRT\",,,\"FAX打印总计数器\"
,,,,,\"RMT-PRT\",,,\"遥控打印总计数器\"
,,,,,\"BOX-PRT\",,,\"BOX打印总计数器\"
,,,,,\"RPT-PRT\",,,\"报告打印总计数器\"
,,,,,\"2-SIDE\",,,\"双面打印总计数器\"
,,,,,\"SCAN\",,,\"扫描器计数器\"
,\"PICK-UP\",,,\"纸路搓纸计数器\"
,,,,,\"C1\",,,\"右前置纸仓(1500张)(第1纸盒)搓纸总计数器\"
,,,,,\"C2\",,,\"左前置纸仓(1500张)(第2纸盒)搓纸总计数器\"
,,,,,\"C3\",,,\"前置纸盒3(550张)的搓纸总计数器\"
,,,,,\"C4\",,,\"前置纸盒4(550张)的搓纸总计数器\"
,,,,,\"MF\",,,\"手送纸盘的搓纸总计数器\"
,,,,,\"DKP\",,,\"选购件3500张右侧纸仓(G1)的搓纸总计数器\"
,,,,,\"2-SIDE\",,,\"双面第2面的搓纸总计数器\"
,\"FEEDER\",,,\"输稿器计数器\"
,,,,,\"FEED\",,,\"输稿器搓纸总计数器\"
,\"JAM\",,,\"卡纸计数器\"
,,,,,\"TOTAL\",,,\"卡纸总计数器\"
,,,,,\"FEEDER\",,,\"输稿时卡纸总计数器\"
,,,,,\"SORTER\",,,\"分页时卡纸总计数器\"
,,,,,\"2-SIDE\",,,\"双面卡纸总计数器\"
,,,,,\"MF\",,,\"手送纸盘的卡纸总计数器\"
,,,,,\"C1\",,,\"右前置纸仓(1500张)(第1纸盒)卡纸总计数器\"
,,,,,\"C2\",,,\"左前置纸仓(1500张)(第2纸盒)卡纸总计数器\"
,,,,,\"C3\",,,\"前置纸盒3(550张)的卡纸总计数器\"
,,,,,\"C4\",,,\"前置纸盒4(550张)的卡纸总计数器\"
,,,,,\"DK\",,,\"选购件3500张右侧纸仓(G1)的卡纸总计数器\"
,\"MISC\",,,\"其他计数器\"
,,,,,\"FIX-WEB\",,,\"定影清洁卷筒纸计数器\"
,,,,,,,,\"该计数达到2000时显示\\\"E005\\\"(更换定影清洁卷筒纸后该计数器要清除)\"
,,,,,\"WST-TNR\",,,\"废粉计数器\"
,,,,,,,,\"(废粉处理后该计数器要清除)\"
,,,,,,,,,,\"CANON 佳能 iR5000/iR6000 数码复印机维修报告\"
,,,,,,\"选择COPIRE >FUNCTION>MISC-P>P-PRINT按OK键,打印出打印维修模式一览表\"
,,,,,,,,,\"COPY SERVICE REPORT\",,,,,,,,\"单位\",,,,,,,,\"机号\"
,\"PRD-C-1\",,,\"定期更换件计数器\"
,,,,\"PRM-WIRE\",,,\"一次充电电极丝计数器\"
,,,,\"PRM-GRID\",,,\"一次栅极电电极丝计数器\"
,,,,\"PO-WIRE\",,,\"转印前电极丝计数器\"
,,,,\"TR-WIRE\",,,\"转印电极丝计数器\"
,,,,\"SP-WIRE\",,,\"分离电极丝计数器\"
,,,,\"PRM-VLN\",,,\"定影主热敏电阻TH1计数器\"
,,,,\"TR-CLN\",,,\"定影副热敏电阻TH2计数器\"
,,,,\"PO-CLN\",,,\"定影热敏开关TP1计数器\"
,,,,\"PS-CLN\",,,\"一次充电电极丝清洁计数器\"
,,,,\"FIX-TH1\",,,\"转印前电极丝清洁计数器\"
,,,,\"FIX-TH2\",,,\"转印电极丝清洁计数器\"
,,,,\"FX-TSW\",,,\"分离电极丝清洁计数器\"
,,,,\"OZ-FLE3\",,,\"臭氧过滤片[FG5-8812;50万张](FM3)计数器\"
,\"DRBL-1\",,,\"消耗零部件计数器-1\"
,,,,\"PRM-UNIT\",,,\"一次充电器计数器\"
,,,,\"PO-UNIT\",,,\"转印前充电器计数器\"
,,,,\"PO-SCRPR\",,,\"转印前充电器象皮擦计数器\"
,,,,\"T/S-UNIT\",,,\"转印/分离充电器计数器\"
,,,,\"CLN-BLD\",,,\"清洁刮板计数器\"
,,,,\"SP-CLAW\",,,\"分离爪计数器\"
,,,,\"DVG-CYL\",,,\"显影滚筒计数器\"
,,,,\"DVG-ROLL\",,,\"显影器计数器\"
,,,,\"C3-PU-RL\",,,\"前置纸盒3(550张)输纸辊计数器\"
,,,,\"C3-SP-RL\",,,\"前置纸盒3(550张)分离辊计数器\"
,,,,\"C3-FD-RL\",,,\"前置纸盒3(550张)搬送辊计数器\"
,,,,\"C4-PU-RL\",,,\"前置纸盒4(550张)输纸辊计数器\"
,,,,\"C4-SP-RL\",,,\"前置纸盒4(550张)分离辊计数器\"
,,,,\"C4-FD-RL\",,,\"前置纸盒4(550张)搬送辊计数器\"
,,,,\"LD-PU-RL\",,,\"左前置纸仓(1500张)输纸辊计数器\"
,,,,\"LD-SP-RL\",,,\"左前置纸仓(1500张)分离辊计数器\"
,,,,\"LD-FD-RL\",,,\"左前置纸仓(1500张)搬送辊计数器\"
,,,,\"RD-PU-RL\",,,\"右前置纸仓(1500张)输纸辊计数器\"
,,,,\"RD-SP-RL\",,,\"右前置纸仓(1500张)分离辊计数器\"
,,,,\"RD-FD-RL\",,,\"右前置纸仓(1500张)搬送辊计数器\"
,,,,\"M-SP-RL\",,,\"手送纸盘分离辊计数器\"
,,,,\"M-PO-RL\",,,\"手送纸盘搬送辊计数器\"
,,,,\"M-FD-RL\",,,\"手送引拨轮计数器\"
,,,,\"FX-UP-RL\",,,\"定影上辊计数器\"
,,,,\"FX-LW-RL\",,,\"定影下辊计数器\"
,,,,\"FX-IN-BS\",,,\"定影隔热轴套计数器\"
,,,,\"FX-WEB\",,,\"定影清洁纸带计数器(30万张);注:更换定影清洁纸带后要将计数器清零\"
,,,,\"DLV-UCLW\",,,\"排纸上分离爪计数器\"
,,,,\"DLV-LCLW\",,,\"排纸下分离爪计数器\"
,,,,,,,,,,\"CANON 佳能 iR5000/iR6000 数码复印机维修报告\"
,,,,,,\"选择COPIRE >FUNCTION>MISC-P>P-PRINT按OK键,打印出打印维修模式一览表\"
,,,,,,,,,\"COPY SERVICE REPORT\",,,,,,,,\"单位\",,,,,,,,\"机号\"
,\"DRBL2\",,,\"消耗零部件计数器-2\"
,,,,\"DF-PU-RL\",,,\"ADF的输纸辊计数器\"
,,,,\"DF-SP-PL\",,,\"ADF的分离板计数器\"
,,,,\"DF-SP-PD\",,,\"ADF的分离导片计数器\"
,,,,\"DF-FD-RL\",,,\"ADF的搬送辊计数器\"
,,,,\"LNT-TAPE\",,,\"ADF的集尘带技术区计数器\"
,,,,\"PD-PU-RL\",,,\"选购件3500张右侧纸仓(G1)的输纸辊计数器\"
,,,,\"PD-SP-RL\",,,\"选购件3500张右侧纸仓(G1)的分离辊计数器\"
,,,,\"PD-FD-RL\",,,\"选购件3500张右侧纸仓(G1)的搬送辊计数器\"
,,,,\"FIN-STPR\",,,\"装订器计数器\"
,,,,\"FIN-FDBL\",,,\"分页器搬送皮带计数器\"
,,,,\"FIN-PDDL\",,,\"分页器页片计数器\"
,,,,\"SDL-STPL\",,,\"鞍式装订计数器\"
,,,,\"PUNCH\",,,\"打孔计数器\"
,,,,\"PNCH-HRS\",,,\"打孔索线计数器\"
,\"定期更换/消耗品零部件计数器的检查: \"
,,,,,,,\"(定期更换PRDC-1/消耗品零部件DRBL-1/消耗品零部件DRBL-2)\"
,,,,\"例:PRM-WIRE / 00000027 / 00500000 / 0% !! 000082\"
,,,,\"PRM-WIRE,零部件名称, 本例中的PRM-WIRE为一次充电电极丝计数器\"
,,,,\"00000027 为一次充电电极丝计数器实际使用张数 (该零部件更换后要将该计数器清除)\"
,,,,\"00500000 为一次充电电极丝零部件限定的使用张数 (在该项目中可设定,设定后按\\\"OK\\\"键)\"
,,,,\"0% 为实际使用张数与限定使用张数的比值,当比值达到90～100%时显示1个 ! ;超过100%时显示2个 !! \"
\" \",\" \",,,\"000082 为预计在82天后需要更换一次充电电极丝零部件. \"
,,,,\"CANON 佳能 iR5000/iR6000 数码复印机卡纸记录/出